Related
I was trying to flash my trinity but i am having problems,
I can get the phone into the bootloader mode without any problems
and the software see the phone ok but the update only gets 1% before it fails with "error 270 image is corrupt" i have tried many different image but the same occurs with them all.
My phone now only goes to the splash screen
is there any think i can do?
take a look at this thread, it may help you unbrick your Trinity...
thanks but no , my phone is not stuck in the bootloader just will not flash
Go HERE they might have a solution there!
Please don't double post! It will not give you a solution twice as fast
Hi. I had the same issue and solved it. feel free to send a MP if you still need help
Thanks still can not get working.. sent a pm to tonio94 thanks mate
Error 270
Hi m8,
Your error 270 is because your phone is still locked and the ROM(s) you are trying to flash are not natively signed for use on your particular phone!
You can either...
1. Pay to get your phone unlocked
2. Set your phone with Hard-SPL (see the related sticky on this very Forum)
3. Extract the .nbh file from the ROM you are trying to flash and flash it using the SoftSPL (SSPL) - again see the sticky on this very Forum.
Not being funny, but you really must do a bit of background reading before you start messing with these new ROM's on your phone.
I hope this helps - PM me if you need more detail.
Moz.
Same problem
Hello,
I've followed the thread to unlock cid/sim my 3600, but I can't upgrade nothing. I can't upgrade hardspl to.
With all roms, the phone stay on tricolor screen after "Yes" to allow enterbootloader.exe, and the rom tell me that the device is not connected.
Active sync was ok, the phone battery to.
Help?
I've 1.23.406 rom actually, and spl 1.07 ds.
EDIT: I've the soluce. I use the SSPL-TRIN for each upgrade, before the hard spl, before passing in 1.41, et now before the ROM, and it runs!!
I had not understood the thread about sspl-trin to bypass, so I didn't use properly.
Now it's ok...
hello folks....
first: sorry for my bad english...
second: i've got a LITTLE problem:
last nite i've tried to flash a new rom on my wizard...
it wasn't the first time.. but... the second!!
something goes wrong...
during the upgrade, windows crashed (blue page), now, if i press the power button, lights come up and its stuck for at least two hours on a white screen..
then, come up the splash screen where are wrote IPL, SPL, ecc...
i write them down:
IPL 2.21.0001
SPL 2.21.Olip
GSM 02.07.10
OS 10.1.0.811 (isn't bad???)
now, the fone stuck forever...
i can't enter in the bootloader so i can't flash it again whit a RUU..
but, the strangest thing... is: the splash screen is from the old rom...
any suggestion??
ah... the rom is this:
XM6r5
http://forum.xda-developers.com/showthread.php?t=355591
how can i fix it? yes... i know... i messed up....
thanx for your answers... even if i can't recover!
If it displays IPL/SPL,then its in Bootloaders,you can flash it in bootloaders.take out the battery for awhile say 30-60 minutes and put it back and try to get into bootloaders and flash the rom.
As its already HardSPL,there shudn't be any problem,just a bad flash due to pc crash.
ok... did it... now, wm starts... but, not everytime.... most of time, it stuck on the famous white screen...
the OS still 10.1.0.811.. i think that is not normal...
how can i "flashback" evreything? i mean... which rom do i use, to have a good base to flash some other rom? my device is a G4.. so, the "love" rom is ok?
EDIT:
i flashed the "wizard_love" rom.. not any problem...till, i've rebooted... white screen again... but when i pressed the power button, it rang like when it seys you "u gonna lose some data" (or something like that)...
SO... Is the screen F******(gone)?
hmmm,perhaps the LCD is a gonner,digitizer or the flexi-cable is creating problems.If you know something about disassembling the device,check if the flexi-cable is properely fixed,otherwise,take it to some repair shop.
simulat problem
hi guys I recently flashed my wizzard with the latest snn edition everything was fine but i tried to install some other program which i did not like so i uninstalled the program system asked me to reboot but now it got stock on the gray windows mobil snn screen i've tried to hard reset with no luck i remove the battery over night still no luck it is bricked? THX
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Before I flashed my first rom, I read wiki.xda-developers.com to make sure I understood what I was doing, and used the search button, instead of risking turning my phone into a paper weight.
Since then, Crackwhore has written a very helpful post at the top of this forum about how to use HSPL and USPL to allow you to flash roms.
yeah i know all that. not my first time flashing a phone but the first time it got stuck loading the bootloader. and specially when i´ve only used the HTC update.
darfor said:
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Click to expand...
Click to collapse
you mean you couldn't get to boot loader page?
So you already have HSPL 1.56 installed (or have SPL1.54 and used USPL)?
If you have HSPL you could try renaming the .nbh file to blacimg.nbh and copying it to the SD card and entering bootloader
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
AFW said:
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
Click to expand...
Click to collapse
try dnloading the rom again amd try.
the file might be corrupt
Have tried that many times. File is not corrupt. I'm getting really worried this is now a brick...
OK, if you can get phone into bootloader, it is not bricked
What does your SPL say in bootloader? Do you get any errors when trying to flash rom? Are you using USPL or HSPL? If USPL, you have to use it before every flash to new rom or radio. If HSPL, are you using correct version?
Was on Dutty's 3.9 XT, but decided to revert to standard WWE 1.56. I flashed the Std 1.56 ROM successfuly, and then tried to restore the ship SPL 1.54 using the card flash method. This failed, and now I'm stuck on the bootlader screen forever.
No matter what I do the THD always goes to bootloader (red-green-blue-white screen), with following text:
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error
Please try again
USB
Click to expand...
Click to collapse
When I start blac_uspl.exe (USPL 2.5), a window flashes (Vista64) for a split second and then nothing else happens. The Vista64 system's USBs work with THD and have been used to sync over past few months.
When I try to run HSPLWrapper_Blackstone_156OliNex.exe and step through the preliminary screens, the Verify that you want to update ROM version screen has the From Image Version as blank and the To Image Version as 1.56.Olinex. When I click to commit the flash the THD screen switches to white with a progress indicator that always stays at 0% until it times out. Recovery does nothing and the same thing always happens. Using Vista64. .Net installed and fine. I can't use the card method (BLACIMG.NBH) - the system also stays on "Loading .... 0%" and nothing else happens.
When I try to flash anything (have tried HSPL1.56, Dutty's 3.9 ROM, stock 1.54 spl) using the card method, the system says "Loading . . ." and hangs there forever without a progress indicator showing.
Your SPL says 1.54.0000. When you try and run USPL.exe have you remembered to disable your antivirus?
Have you tried usb method instead of card for flashing rom?
I know you have said that youi have used usb for syncing, but when in bootloader does it change from 'serial' to 'usb' when you connect HD to PC?
Fallen Spartan - I want to thank you for taking the time to help me resolve this problem. Very much appreciated!
1. Yes, anti-virus disabled and indeed removed from the PC.
2. Yes, have tried the USB method at least 20 times.
3. Yes, the bootloader changes from Serial to USB. It then goes to the progress indicator screen and hangs on 0%. The progress indicator on the RUU on PC also stays at 0% and eventually times out. I've gone through the Recovery routine at least 20 times, with no luck.
When I try to run SSPL-Manual-TouchHD.exe it says "not a valid Win32 application".
I'm a bit perplexed by this.
You have obviously successfully flashed Duttys V3.9 so drivers are fine, you know how to use USPL, both flashing methods (SD card and usb/pc), disabled anti-virus, phone in bootloader.
Have you tried to reflash 1.56 rom or possibly performing a hard reset before trying to use USPL or HSPL. I doubt this would make a difference though.
Have you tried cRaCKwHoRe's USPL GUI v 2.5 Application?
You don't get any code errors?? I'm struggling to find a solution here.
Yes, this is most vexing. I've flashed innumerable times before and never had an issue. I suspect the SPL is fine, but somehow the actual WM ROM image is corrupted. Will now try to load Std 1.56 ROM image again...
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa (though I'm a rugby fan).
AFW said:
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa.
Click to expand...
Click to collapse
No accomodation required, just glad you got it sorted
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
can anybody help me at all
Adamsville: perhaps you're stuck in bootloader mode because the WM ROM image flashed on your system has become corrupted or disabled, ie the only thing the system can boot into is the bootloader.
Try flashing a new compatible WM ROM image and see if that works.
AdamsvillE said:
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
Click to expand...
Click to collapse
a hardreset followed by a 1.54 base rom will solve all ur probs.
or lower spl to 1.14 cos ur stock rom is a 1.14 base as suggested by th name..
cheers
Hello there,
I messed up my just acquired used HTC Breeze. Isn't too bad, as it wasn't so expensive and it had SIM lock anyway. So hadn't I done anything, then I wouldn't have been able to used it as well.
My question: The info 2 - command returned "HTCSF kEØ(HTCE", so as far as I understand the bootloader has been bricked. But why can I still get to the three-color-screen? I always thought, this is only possible, if the bootloader is not bricked. I'm very sure I read about that regarding a HTC Canary.Or isn't that the case anymore with never devices?
In case anyone's interested, the whole story:
I tried the Hermes unlocker-method, but couldn't get it to work. The first problem was, that SSPL didn't work, because my phone was app-locked. Well removing the app-lock wasn't that hard.
I eventually managed to find out, how exactly this SSPL-stuff works. However, I still couldn't use the Hermes-unlocker. Flashing with SD-card wouldn't work - and using the RUU would only cause the phone to reboot, hence leaving the SPPL and being stuck with the normal bootloader, which wasn't unlocked (sorry if that sounded too untechnical - you probably know, what I mean).
So my last hope was the thread "Application UNLOCK/SSPL/HARDSPL" . First I upgraded to SPL 1.09 (might have been a bad choice, as I didn't think it through). Phone would still work then. Then I tried RUU_MTeoR_1.34.251.1_1.38.00.10_HTCEUR_SHIP , which is where I probably broke my bootloader, as it wouldn't start the OS after successfully flashing. (although it was IPL 1.00 and SPL 1.09, if I remember correctly).
Then I flashed RUU_BREE100_1.13.251.2_1.06.00.10_QtekEUR_Ship_R3 via SD-Card, cause it's said to have SPL 2.05. With that I wanted to do the final step in the said posting - flashing hardspl, so that I'd get SPL 7.77 anytime, without SSPL. I thought, the Hermes unlocker might work then. Only it was a dead end. After flashing to RUU_BREE100_1.13.251.2_1.06.00.10_QtekEUR_Ship_R3, I couldn't get anything to work anymore. And now I'm stuck with IPL 0.90 and SPL 1.09. End of the Story
If you can see three color screen (bootloader) that's mean it's ok Try flash with shipped ROM from the bootloader mode. I can upload it to you, but I have to know your device brand (CID lock)...
Hi there,
Here's the situation. I tried to fix a problem with my microphone in android by flashing back to the stock AT&T rom for kaiser which came with the phone. It ran and seemed to update, but did not install windows mobile.
When I put KAISDIAG.nbh on the flash (formatted FAT32), it gets stuck at the loading screen (white background, displaying 'Loading...'
When I try the windows mobile 6.5 KAISIMG.nbh, the same thing happens.
When I remove the KAISDIAG.nbh from the flash drive, and then try the stock windows mobile 6.1 KAISIMG.nbh, it doesn't freeze, instead it checks the ROM, and then displays 'NOT ALLOW'.
The rgb screen has the following info:
KAIS1*0
SPL-1.56.0000
CPLD-8
Any ideas on what my next step should be?
Thanks
Update: Tried doing it via usb, and now i keep getting error code 294: Invalid vendor id. I guess this means i have to find another ROM? Just tried 2 different stock downloaded from links on these forums. Both of them produce the same error.
Update 2: Tried updating my SPL version to 3.29 and 3.56 from the forum - it doesn't work (stuck at the same loading screen). I am out of ideas. If anyone is aware of anyway I can flash a rom and/or update my SPL (maybe this is the problem), I would be grateful.
Solved: I had to try several of the 'stock' ATT builds to get it to work. The one which was successful for me can be found here forum.xda-developers.com/showthread.php?t=343198