I case of people who don´t read 200 post and still brick their device - here is the guide that worked for ALL people with:
HTC P4350
XDA Terra
WING
with IPL 4.xxx and higher!!! (that is IMPORTANT)
and then follow this:
Default
For me it was working when:
1. install canonyang.cab
2. install aserpolicy.cab
3- install disablesecurity.cab
4. SOFTRESET
5. run RUU from Hard-SPLWM6 folder verison 4.70.yang
6. screen will become white - WAIT until it reboots itselfe.
7. done!
check if SPL now is 4.70.yang
Fore sure: I used this
http://rapidshare.de/files/38148213/HardSpl_WM6.rar.html
mirror: http://www.sendspace.com/file/ot8zsn
It worked for many others, too.
b.mann said:
I've figured my issue out, maybe I can help the others that get the 202 Connection error.
On your device--BEFORE Hard-SPL--go to Settings->Connections->USB to PC and check that checkbox.
If it's not checked, most times you will get the 202 Connection error. Hard-SPL and you should be good to go!!
Click to expand...
Click to collapse
You may add Dopod C800 to the list
It's the real deal
Succesfully flashed my device under papamopps supervision and can verify that this HardSPL package is working 100%
Thanks again papamopps
heya, seems like i'll get my terra flashed then too. Nice one. Well, at least to some point...i almost fear to ask...how do i see if i have "IPL 4.xxx and higher"?
I've got Rom-version 4.11.207.1 GER, Protokoll-Version 4.1.13.39
TIA for help
*BTW, the rapidshare-link tells me "file not found".
stahlsau said:
heya, seems like i'll get my terra flashed then too. Nice one. Well, at least to some point...i almost fear to ask...how do i see if i have "IPL 4.xxx and higher"?
I've got Rom-version 4.11.207.1 GER, Protokoll-Version 4.1.13.39
TIA for help
*BTW, the rapidshare-link tells me "file not found".
Click to expand...
Click to collapse
Softreset your Herald and press the Camara butten until you see an Colerd screen it´s the Bootloader. there you will find the IPL and SPL on the screen. softreset your herald without pressing any butten and it will start normely to youre WM. You wont delete any data aslong you nothing Flash.
Ghostrider
stahlsau said:
heya, seems like i'll get my terra flashed then too. Nice one. Well, at least to some point...i almost fear to ask...how do i see if i have "IPL 4.xxx and higher"?
I've got Rom-version 4.11.207.1 GER, Protokoll-Version 4.1.13.39
TIA for help
*BTW, the rapidshare-link tells me "file not found".
Click to expand...
Click to collapse
link updated!
Thanks!!
yew i am hardspl but it change my boot screen oooo i have to reflash nvm
aron4588 said:
yew i am hardspl but it change my boot screen oooo i have to reflash nvm
Click to expand...
Click to collapse
could you shareyour device information-so that we can see for which device it is working?!
It worked on my:
HTC p4350
It had: WM6 overclocked to 299Mhz (but i let it on Default 201Mhz When I was in de process)
It had de 4mb Page Pool.
Worked great!!! THanks man!
BTW- afteryou have Hard-SPL.
Never use an official RUU with included SPL.nbh (delete this ebfore flashing)
And never use the RUU from Hard-SPL
Allways use the included RUU or take an RUU without SPL.bnh when you onlycan download the ruu_wigned.nbh.
Regards
how to go back to stock?
i currently have hard spl with touchit 4.4
i want to go back to factory spl and factory ruu
can someone please help me?
thank you
i did it with t-mobile wing usa
aron4588 said:
i did it with t-mobile wing usa
Click to expand...
Click to collapse
I also was able to Hard-SPL my T-Mobile wing successfully in the US
and....
in the past ive always went stock b 4 flashing a new rom
what are the steps now to change to new roms? wheather it b hard spl or factory spl
thanks
I am waiting from 20 minutes with my phone in white screen mode... is it normal?
EDIT: ehm... please... im am quite worried. (30 minutes in white screen :S)
johnny88 said:
I am waiting from 20 minutes with my phone in white screen mode... is it normal?
Click to expand...
Click to collapse
it should end after 10 or 15 minutes.
hope you installed all files before and softreset.....
yes all cabs...
during the install of hardspl the ruu install wizard shows a windows with "connection failure" and only an Exit button. I click on it while it is in white mode... I am still waiting...
What should I do? (wainting or reset?)
finally (after 40 minutes of white screen) I softreset with stylus...
It reboots normally as nothing was appened... better then brick.
I will try again later.
THX!
hi
when HTC P4350 is into bootloader mode, SPL and IPL are 1.08.0001
is it an older SPL or waht?
if yes can i update my P4350 to WM6 without using Hard-SPLWM6 ??
any idea?
anyone have a link to learn what's is exactly hard SPL, and the difference between HARD SPL and SOFT SPL
thx in advance
br
BouRRi_GSM said:
hi
when HTC P4350 is into bootloader mode, SPL and IPL are 1.08.0001
is it an older SPL or waht?
if yes can i update my P4350 to WM6 without using Hard-SPLWM6 ??
any idea?
anyone have a link to learn what's is exactly hard SPL, and the difference between HARD SPL and SOFT SPL
thx in advance
br
Click to expand...
Click to collapse
allways start with :
http://forum.xda-developers.com/showthread.php?t=327046
and then try one of this:
http://forum.xda-developers.com/showthread.php?t=358030
first the official one....
and read- read - read
Related
I tried reflashing my IMATE KJAM to WM6
The process went till 35% and then got disconnected.
Now its stcuk on the Bootloader Screen(Three colors screen)
Tried the Hard Reset(comm mann+voice button+reset)
It doesnt do a hard reset, the same screen flashes back again.
Tried reflashing i get the Error 300
The previous ROm was crossbow underground edition.
Please help and let me know whats next that i can do.
paraozzy said:
I tried reflashing my IMATE KJAM to WM6
The process went till 35% and then got disconnected.
Now its stcuk on the Bootloader Screen(Three colors screen)
Tried the Hard Reset(comm mann+voice button+reset)
It doesnt do a hard reset, the same screen flashes back again.
Tried reflashing i get the Error 300
The previous ROm was crossbow underground edition.
Please help and let me know whats next that i can do.
Click to expand...
Click to collapse
You know what the totally histerical thing about this is? This is the exact same reason I made my first post. LOL.
Alright I'm gonna try to help you seeing as how it doesn't look like too many others are looking here.
I have several questions first before I can help you.
1. Who is your wireless service provider? IE: T-Mobile, Cingular, Etc...
2. What Is your IPL/SPL?
Answer these 2 questions for me and I will be able to better help you.
Thanks for the quick reponse
Now the irony is i am here in nepal and i use the phone as a simple mobile phone, but as far as i know i remember flashing a T-Mobile ROM while upgrading to WM6, the IPL and SPL both are 2.26, i unlocked the device while upgrading..
Thanks
Kushal
paraozzy said:
I tried reflashing my IMATE KJAM to WM6
The process went till 35% and then got disconnected.
Now its stcuk on the Bootloader Screen(Three colors screen)
Tried the Hard Reset(comm mann+voice button+reset)
It doesnt do a hard reset, the same screen flashes back again.
Tried reflashing i get the Error 300
The previous ROm was crossbow underground edition.
Please help and let me know whats next that i can do.
Click to expand...
Click to collapse
Hey!
ok lets c if I may be of some help here,if u r in bootloader screen than try to reflash again T-mobile 2.26 rom and if it goes alright than go on to flash any other wm6 cooked roms.
or
if it doesnt flash than i wud suggest u reflash back the buttons 105 rom to get back to ipl/spl 1.05,than again use lokiwiz tool to unlock cid & reflash T-Mobile to gain ipl.spl 2.26
hope it works out.it happened once with me also, I did the same & now I'am running wm6 XM6r3 Rom,Secondly u can use the WST TOOL by Mestrini to verify ur device status, u can even Cid unlock ur device with it, Goodluck
Yup man flashing the T-mobile 2.26 did the job..
Great thanks for the same..
paraozzy said:
Yup man flashing the T-mobile 2.26 did the job..
Great thanks for the same..
Click to expand...
Click to collapse
glade you got it up and running good luck and happy flashing
Is my K-Jam totally bricked?
It is now stuck up in bootloader screen.
I am able to swtch it off with power button. I can also have first flash screen.
On connecting with USB port, it shows yellow light indicating that it is charging & that over a period of time, goes green.
Earlier I had flashed TNT ROM but while reflashing newer it got stuck up as after flashing, I tried to hard reset [mistakenly thought ROM is flushed fully] & could not go further after initail first screen.
Other details:
IPL:2.16
SPL:2.16
GSM:02.07.10
O.S.:11.0.0.2
May some one help?
Thanks in advance.
Virat
Nopes ! its not 'Bricked' just had a bad flash. As long as it gets into bootloaders ,its perfectly safe. Perhaps,your phone is not CID unlocked ?
Download the official carrier's rom from its website and flash it in the bootloaders,it'll start to work fine.Then read the guide to cid unlock and upgrade.
Cheers!
boot issues
hi
i am having serious problems with my kjam.i installed black diamond's rom and now my phone boots upto the splash screen where it shows window mobile 6 and gets stuck there.
i have tried a soft spl, but it doesnt help as the phone cant connect or move from the splash screen.also, i can make call or do anything with the phone.
can someone assist me and also point me to a place where i can find the lastest tnt rom.
ghumanfly said:
hi
i am having serious problems with my kjam.i installed black diamond's rom and now my phone boots upto the splash screen where it shows window mobile 6 and gets stuck there.
i have tried a soft spl, but it doesnt help as the phone cant connect or move from the splash screen.also, i can make call or do anything with the phone.
can someone assist me and also point me to a place where i can find the lastest tnt rom.
Click to expand...
Click to collapse
Always post vital data of the phone,which is your device G3 or G4.Have you Tried Soft Reset or Hard Reset.it sometimes help.
Well,if it's a G3,is it SIM/CID unlocked,cuz its required to get the phone CID unlocked to upgrade to wm6,but if its a G4,then use method 'SoftSPL' or 'HardSPL' as it cannot be CID unlocked.
Post IPL/SPL...? of the phone here.
You can find all the latest wm6 Roms in 'Wizard Mobile 6' forum.
Cheers!
Thanks but solution found while reflashing in XP
Thanks for the reassurance Zabardast. I cold not even reflash it with vista but in xp, it sailed smooth. It is working normal now. Any way, thanks again for responding.
Virat
virat said:
Thanks for the reassurance Zabardast. I cold not even reflash it with vista but in xp, it sailed smooth. It is working normal now. Any way, thanks again for responding.
Virat
Click to expand...
Click to collapse
Thanks !
Glade you got it working
Have a nice day !
zabardast_1 said:
Always post vital data of the phone,which is your device G3 or G4.Have you Tried Soft Reset or Hard Reset.it sometimes help.
Well,if it's a G3,is it SIM/CID unlocked,cuz its required to get the phone CID unlocked to upgrade to wm6,but if its a G4,then use method 'SoftSPL' or 'HardSPL' as it cannot be CID unlocked.
Post IPL/SPL...? of the phone here.
You can find all the latest wm6 Roms in 'Wizard Mobile 6' forum.
Cheers!
Click to expand...
Click to collapse
Wireless Carrier
Vodacom
IPL - 2.16.0001
SPL - 2.16.0001
rom version - 2.16.9.1
radio - 02.07.10
extROM - 2.16.9.101
OS - WM5
Roms tried
BlackDiamond 3.1
i am running XP SP2 on my notebook.
i have restored the original WM5 rom however my screen is now fuzzy.
ghumanfly said:
Wireless Carrier
Vodacom
IPL - 2.16.0001
SPL - 2.16.0001
rom version - 2.16.9.1
radio - 02.07.10
extROM - 2.16.9.101
OS - WM5
Roms tried
BlackDiamond 3.1
i am running XP SP2 on my notebook.
i have restored the original WM5 rom however my screen is now fuzzy.
Click to expand...
Click to collapse
'Hard Reset' the phone,hope it'll work fine.
Well,I assume,you cudn't do the SoftSPL correctly the first time,try to apply the SpftSPL again correctly,if it works,ok,otherwise you can upgrade to wm6 with HardSPL method.
ba salam khedmate aghaye zebardast
duste aziz man ppc imate kjam daram ke eshtebahan soft spl kardam va rom wm6 prophet rush rikhtam ba tavajoh be inke seri gushi man g4 wizard bashe (ipl&spl 2.16.0001) kholase gushi alan tu safeye avali ke windows ba yek logo az rom marbuteh miad bala gir mikoneh .albateh 2 ta rom kjam asli wm5 ham gir avordam rikhtam vali hamunjuriye albateh jaye shokresh baghiye ke gushi tu halat bootloader gharar migireh va hard reset ham mishe. lotfan be man komak konid ta moshkelam ro hal konam. ba tashakor az shoma
could you please ,solve my problem kjam g4 wizard
laike salam brother
thank you very much for direction. I want to answer your question:
Quote:1. Which was the original official rom running on the phone before you tried to upgrade ?
1- I think wm5 belonge to 2005 becose it is written under the battrey.
Quote:2. What was the original wm5 rom and IPL/SPL of the phone before ?
2- I couldent remember but this phone approved by uaelab company [TA-2005/453 approved][E05/14/40225/g]and I flash with different official rom which you mentioned at ftp://ftp.clubimate.com but nothing happend ,maybe I do somthing wrong.
Quote:3.What exactly you mean you copied jumpspl to the root of the phone,did you applied SoftSPL ?
3- yes correct I did softspl with whit coulor screen then connected to pc and did toast that .
also I have problem to connect wst 4.2.2 to my ppc.
I download it and run, but the software couldent detect my fhone I dont know why .I connet it from bootloader 3coulor but nothing happen and so on.
could you please to explain how can I work with wst 4.2.2 also very important how to connect that because it says I have to connection with activesync .
pls direct me pls
mamnun
kourosh
hi guys,
i was excited about the new Radio upgrade, so i tried to flash it. i got an error, because my SPL is 2.05. so i tried to unlock the phone using jerpelea's guide, flash to 1.09 -->success, then WWE (1.10) but an error occured saying invalid vendor ID during WWE flash. now i have SPL 1.09 on my phone and my phone is stuck on the 2nd boot screen of jerpelea's WM6.1 beta 4 ROM. my phone is fully unlocked using jerpelea's unlock guide, that's how i got to install SPL 1.09 successfully. how can i recover my phone? please help.
Update 1: i tried to flash back the original dopod 595 WM5 ROM. i mixed the RUU updater from the latest official ROM with the nbh from dopod WM5 ROM. the flashing works. when it's 100%, the phone reboots and, i got back to the same problem. stuck at 2nd/3rd boot screen. i now have IPL-0.90 and SPL 1.09 on my phone. Please help me to recover my phone. i've tried to hard SPL shown in the wiki guide, doesnt work. says invalid vendor ID crap. i really dont know what to do now.
Update 2: when the device boots, it stucks on the 2nd/3rd boot screen and if the USB cable is attached, for a brief moment, windows can detect the phone and i can even browse the content of the phone from my PC. but after that, the device disconnects itself and just remain stuck at the 2nd/3rd boot screen. the device appears to be totally freezed/hang. even the LED charging indicator will not turn off when i unplug the device from computer
i believe what i need to do now is to make a nbh image that is signed to i dont get any corrupted image message when trying to flash. i used HTC ROM editor to mix and match the SPL and IPL file so that i can downgrade the SPL to 2.05 and upgrade it again later. but i dont know how to sign nbh files.
If i were you I'd use this one =)
futureshock said:
ok i found it i didn't read further the 1st page on sspl thread
edit:
have repacked it with runme.bat and 77.7er SSPL ...
Radinly_1.54.30.10
Click to expand...
Click to collapse
At least I did and it worked =)
and then I'll highly recommend this WIM6.1 release by FutureShock: http://forum.xda-developers.com/showthread.php?p=2094056#post2094056
GL =)
I've GOT IT!!! using various mix and match method, im flashing the phone now!!! fingers crossed it'll boot later
UPDATE: DOESNT WORK! PLEASE HELP
It sure will.. Even I got it to work really fine
crap!. doesnt work. it's still SPL 1.09 and stuck at 2nd boot screen.
is there a ROM editor that works for meteor? can someone please suggest one that can be used to sign the nbh file.
jerpelea, or futureshock, please help
not good news
I think I know what do you mean. My device was in very same state like yours few mnonths ago.
Try to run mtty and the command "info 2" without quotes.
Do not forget to disable USB on activesync settings before running mtty.
You will get an answer which includes the CID of your device.
If not (this was my case), you have to send it to the repair center probably.
My device CID was Qtek_A07 (RUS) and I have tried to instal the first official WWE 1.34 ROM update (combined from SPL.nbh and ROM.nbh) and it replaced only the SPL, and the ROM update crashed.
There was not way out so I sent it to the repair center.
The WWE images are expecting the device with CID Qtek_Z12.
PiGeonCZ said:
I think I know what do you mean. My device was in very same state like yours few mnonths ago.
Try to run mtty and the command "info 2" without quotes.
Do not forget to disable USB on activesync settings before running mtty.
You will get an answer which includes the CID of your device.
If not (this was my case), you have to send it to the repair center probably.
My device CID was Qtek_A07 (RUS) and I have tried to instal the first official WWE 1.34 ROM update (combined from SPL.nbh and ROM.nbh) and it replaced only the SPL, and the ROM update crashed.
There was not way out so I sent it to the repair center.
The WWE images are expecting the device with CID Qtek_Z12.
Click to expand...
Click to collapse
this is what i get with mtty
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
what's the meaning of this? is there any hope?
i ran the format command anyway. device reboots and still stuck at the windows mobile logo screen. what should i do next?
alexnvidia said:
this is what i get with mtty
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
what's the meaning of this? is there any hope?
i ran the format command anyway. device reboots and still stuck at the windows mobile logo screen. what should i do next?
Click to expand...
Click to collapse
why did you format ?
try to reflash 1.09 spl
and after this wwe one of 1.34 roms to get 1.10 spl
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
Click to expand...
Click to collapse
jerpelea: First of all I will say thank you for taking all that time you do spend on the ROM cooking/building/making/what-ever-is-the-right-name and I/we really appreciate it!
jerpelea said:
but i dont know if you have the knowledge
Click to expand...
Click to collapse
I think that comment was really unnecessary!
As a n00b I know how hard it is to understand what’s happening. I did read the wiki’s and still I didn’t get HOW TO upgrade a ROM until I found a great post in FutureShock’s thread
darkDirk said:
First of all:
It's fantastic what you are doing with wm6.1 and the Breeze, Futureshock !
I am new and trying to upgrade it myself, but at first I didn't have any luck.
Here is a simple newby step-by-step manual:
- Download and extract a MTeoR-FutureShock-WM61-xxxx.x.rar
- Check your Mteor battery in more then 50 % full
- connect the Mteor to the computer via usb and check if Activesync works
- go with DOS (cmd line) to the directory and start runme.bat
- On the Mteor press camera and powerbutton at the same time.
- then immediately press any key on the computer to continue the batch script.
- now you should see the 3-color bootscreen
- press any key to start the rom-update program and follow its directions.
When the update is finished (in less then 5 minutes), then wait untill the first boot is complete.
If you don't get the 3-color bootscreen or you the update on the Mteor stays on 0 % and the rom-updater displays an error, try testing this:
On the Mteor start the explorer and in the root directory (press UP once) find SSPL.EXE en start it.
If the Mteor won't start the program and there is an error like "insufficient trustlevel".
You need to remove the application lock on your Mteor.
Run SDA_ApplicationUnlock.exe on your PC with Activesync working and then install SP_AllowCertificateInstall.cab on the Mteor.
You will find those two in the .rar in ".\opt Software\Unlock Tools"
Then redo from the start.
Then, Have fun !! (Futureshock & DarkDirk)
P.S. works on a BREE100 with IPL-0.90 and SPL-2.05.
Click to expand...
Click to collapse
But I still do not know what SSPL, SPL, IPL or whatever there is does to me or/and the phone.
Anyway. Thanks for all the work.
if someone has a corrupt CID just send me an pm...
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
Click to expand...
Click to collapse
with all the respect what you do for this community, isn't taht you who advice us to update the SPL before trying your images?
in this thread http://forum.xda-developers.com/showthread.php?t=384398 you should probably higlight that the update should be done only on WWE devices.
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
Click to expand...
Click to collapse
i did try to read as much as i could but apparently i didnt come across that. when i flashed to SPL 1.09, the device booted up just fine. it is when i try to update to WWE 1.10, the update process failed and bricked my phone. for your information, i was following the exact steps described by you in your unlocking/SSPL guide. you mentioned upgrade to SPL 1.09, then WWE 1.10. this is exactly what i did. i dont know what went wrong. im sure if im as knowlegable as you are, i wouldnt have screwed up my phone. my bad.
just to be fair, your method did work when i updated my dopod 595 (WWE device) to your WM6.1 beta 4 ROM. but i never upgraded my SPL to 1.10. i only thought of upgrading SPL when you posted the new radio release and that's where i screwed up.
anyway, what is important here is, is my phone unrecoverable? im reading the links you posted as i type, and i'll give the methods. maybe based on your experience, you could suggest some ways to do it. thanks.
alexnvidia said:
hi guys,
i was excited about the new Radio upgrade, so i tried to flash it. i got an error, because my SPL is 2.05. so i tried to unlock the phone using jerpelea's guide, flash to 1.09 -->success, then WWE (1.10) but an error occured saying invalid vendor ID during WWE flash. now i have SPL 1.09 on my phone and my phone is stuck on the 2nd boot screen of jerpelea's WM6.1 beta 4 ROM. my phone is fully unlocked using jerpelea's unlock guide, that's how i got to install SPL 1.09 successfully. how can i recover my phone? please help.
Update 1: i tried to flash back the original dopod 595 WM5 ROM. i mixed the RUU updater from the latest official ROM with the nbh from dopod WM5 ROM. the flashing works. when it's 100%, the phone reboots and, i got back to the same problem. stuck at 2nd/3rd boot screen. i now have IPL-0.90 and SPL 1.09 on my phone. Please help me to recover my phone. i've tried to hard SPL shown in the wiki guide, doesnt work. says invalid vendor ID crap. i really dont know what to do now.
Update 2: when the device boots, it stucks on the 2nd/3rd boot screen and if the USB cable is attached, for a brief moment, windows can detect the phone and i can even browse the content of the phone from my PC. but after that, the device disconnects itself and just remain stuck at the 2nd/3rd boot screen. the device appears to be totally freezed/hang. even the LED charging indicator will not turn off when i unplug the device from computer
i believe what i need to do now is to make a nbh image that is signed to i dont get any corrupted image message when trying to flash. i used HTC ROM editor to mix and match the SPL and IPL file so that i can downgrade the SPL to 2.05 and upgrade it again later. but i dont know how to sign nbh files.
Click to expand...
Click to collapse
run terratem
type info2
if it sais A07 then just flash rusian 1.34 rom and enerithing will be fine
application unlock it
run sspl 77.7
flash wm6.1
if it says enithing else you need to locate your original rom
till now i found that it sais a07 in most cases
BR
alexnvidia said:
i did try to read as much as i could but apparently i didnt come across that. when i flashed to SPL 1.09, the device booted up just fine. it is when i try to update to WWE 1.10, the update process failed and bricked my phone. for your information, i was following the exact steps described by you in your unlocking/SSPL guide. you mentioned upgrade to SPL 1.09, then WWE 1.10. this is exactly what i did. i dont know what went wrong. im sure if im as knowlegable as you are, i wouldnt have screwed up my phone. my bad.
just to be fair, your method did work when i updated my dopod 595 (WWE device) to your WM6.1 beta 4 ROM. but i never upgraded my SPL to 1.10. i only thought of upgrading SPL when you posted the new radio release and that's where i screwed up.
anyway, what is important here is, is my phone unrecoverable? im reading the links you posted as i type, and i'll give the methods. maybe based on your experience, you could suggest some ways to do it. thanks.
Click to expand...
Click to collapse
it depends on the info displayed on terraterm
for A07 you can use the russian rom to recover
this is what i got from terraterm. same as mtty.
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
i did flashed back to my original ROM after the first stuck in WM screen incident. and amazingly the flashing process works after several mix and match. after the original (WM5) ROM completed flashing, my IPL is downgraded back to 0.9 and SPL is still 1.09, and im still stuck at the WM logo screen (this time WM5 logo).
terraterm is a tool like mtty
what is your orignal rom??
just try to flash over sdcard... (look in wiki4more infos about that)
futureshock said:
terraterm is a tool like mtty
what is your orignal rom??
just try to flash over sdcard... (look in wiki4more infos about that)
Click to expand...
Click to collapse
i tried SD card flashing too yesterday. it says not allowed. i have already flashed over the original dopod 595 ROM and my phone is now WM5. the flashing is 100% successful, but it is still stuck at the second boot WM screen.
i think im in a really screw up position now. i have SPL 1.09 and IPL 0.9. i dont know what is corrupted now. is it the CID? SPL?
cid you can check with mtty and info 2...
if that so... just do what i have wroted in pm...
you could also just try the old htc rom (w. SPL 2.05)
futureshock said:
cid you can check with mtty and info 2...
if that so... just do what i have wroted in pm...
you could also just try the old htc rom (w. SPL 2.05)
Click to expand...
Click to collapse
both mtty and terraterm give me the same msg when i type info 2. it says time out (refer above for exact error message).
the original dopod 595 rom has SPL2.05. and it was successfully flashed into the phone. when the phone reboots, it is still stuck at 2nd boot screen (WM logo). i checked, the SPL is still 1.09, but IPL has been downgraded to 0.9.
Hello.Sorry for wrong english.
my problem is on cingular 8125
I bought it with problem.
On splash screen it freeze, i flash RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1,because it firmware for cingular 8125. and it freeze too.
Can you help me?
my ipl 2.25
spl 2.25
gsm 02.25.11
os 2.25.11.1
Thank you. and again sorry for wrong english.
Ok Dude here is your solution ive found it myself after Searching
I will not be liable for Bricking your Device you do this at your own Risk*
First of All Is your Phone CID unlocked?
if it is check to see if you can hard reset if your phone says Format is Failed then here is your fix
First flash factory rom
grab a minisd that is blank *Warning it will Overwrite any card you put in*
enter into bootloader
reset+ camera button
in windows xp
Download mtty
http://forum.xda-developers.com/attachment.php?attachmentid=71806&d=1203597568
Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
run program
set port to
\\.\WCEUSBH001
click OK
*Warning it will Overwrite any card you put in*
type in at CMD>
r2sd all
then press enter
after it finishes reset pda and return back into bootloader mode
reset+ camera button
it will ask if you wish to flash from sd press Voice Command button to accept
after 100% complete reset phone you should be able to get back
hello. thank you for a help. mtty says me You didn't get the proper security level to download a specific image. why i do wrong?
cg_ar said:
hello. thank you for a help. mtty says me You didn't get the proper security level to download a specific image. why i do wrong?
Click to expand...
Click to collapse
Your phone is CID locked,Mtty will not work in this situation. Have you tried a Hard Reset.
Does it display any error message while flashing the official Rom,does it complete flashing or stops with a error message ?
Which windows you are flashing with,WinXP or Vista ?
when hard reser it says me a fat format failed. all sw flash without problem.
Anybody know how this is repair? (sorry for wrong english)
cg_ar said:
when hard reser it says me a fat format failed. all sw flash without problem.
Anybody know how this is repair? (sorry for wrong english)
Click to expand...
Click to collapse
how it cid unlock in bootloader mode?
cg_ar said:
how it cid unlock in bootloader mode?
Click to expand...
Click to collapse
You cannot CID unlock in the Bootloaders,it has to have a working OS (Rom),try to flash a rom,try these roms,lets hope one of them might work, Button's Rom 1.05 or xda_minis_launch or wizard_love_rom and official rom of your carrier and if there's any sdcard/mini_sdcard inserted in the phone,take it out before flashing,just keep on trying the different roms,its a catch 22 situation,it won't let the rom flash,stuck at splash screen and still it won't get CID unlocked in Bootloaders or use the Mtty method.I can imagine your frustration,but you gotta keep on trying.
i tried Xda_MiniS_LaunchROM_v154102,wizard love,button and original rom from cingular. and it freez on boot at all roms,and cannot make a hard reset. what i will doing next?
in this condition phone is not repairable?
cg_ar said:
in this condition phone is not repairable?
Click to expand...
Click to collapse
YES ! it is repairable,but not free,you'll have to pay for getting the CID unlock code from 'imei-check' uk.They might charge you around 20 or 30 dollars and provide you with a unlocking code,after that you'll be able to flash any Rom,but,here we were trying to get it working free somehow! Anyway, the choice is yours now,but certainly it is repairable,don't loose hope !
zabardast_1 said:
YES ! it is repairable,but not free,you'll have to pay for getting the CID unlock code from 'imei-check' uk.They might charge you around 20 or 30 dollars and provide you with a unlocking code,after that you'll be able to flash any Rom,but,here we were trying to get it working free somehow! Anyway, the choice is yours now,but certainly it is repairable,don't loose hope !
Click to expand...
Click to collapse
I know a way to avoid paying and manage a security_level=0 to allow "r2sd all"
It's just a matter of flashing a SoftSPL for G3 and use mtty
"Hello,
if the device doesn't boot up in windows then unlocker it will not work!
Regards,
IMEI-CHECK Team"
it says on imei-check.
how i will did?
what is softSpl for g3? please give url. thank you
mestrini said:
I know a way to avoid paying and manage a security_level=0 to allow "r2sd all"
It's just a matter of flashing a SoftSPL for G3 and use mtty
Click to expand...
Click to collapse
hey m8
You referring to 'JumpSPL' or something ? thats interesting
cg_ar said:
"Hello,
if the device doesn't boot up in windows then unlocker it will not work!
Regards,
IMEI-CHECK Team"
it says on imei-check.
how i will did?
what is softSpl for g3? please give url. thank you
Click to expand...
Click to collapse
hmmm, so imei-check' said that,yeah ! I presume,you got to have a working OS (Rom)
Well, softSpl for G3, I'm not sure myself,let mestrini handle this.
zabardast_1 said:
hey m8
You referring to 'JumpSPL' or something ? thats interesting
Click to expand...
Click to collapse
Something like that
If i recall correctly while developing SoftSPL for G4, The Equinox also made a G3. Problem is no one ever thought of a use to it (until now, and i have others hehe )
mestrini said:
Something like that
If i recall correctly while developing SoftSPL for G4, The Equinox also made a G3. Problem is no one ever thought of a use to it (until now, and i have others hehe )
Click to expand...
Click to collapse
WOW !
I'm all anxious here...... eyes n ears !!!
i download a wzg3.7z. unpack and have
Hard-SPL.nb
JumpSPL.exe
SPL.lnk
spl.nb.
it has in pack 145kb is it alright?
and jumpspl cannot execute and spl.ink too. How this flash?
cg_ar said:
please mail me softspl for wizard g3. because from my ip on rapidshare already downloading. please mail on cg_ar(a)mail.ru
Click to expand...
Click to collapse
Well, I do realize your frustration,but this application still needs to be tested and tried first,as far as I know,it has not been applied and tried yet.
But keep your fingers crossed as I'm,hope it comes out successful,it wud solve this problem of not allowing to "r2sd all" using mtty in CID locked device.
hmm, there's a flaw in my theory: It's necessary to access WinCE (WM) to allow Haret to do it's job
Maybe there's a work around i can think of...
sorry
cg_ar said:
i download a wzg3.7z. unpack and have
Hard-SPL.nb
JumpSPL.exe
SPL.lnk
spl.nb.
it has in pack 145kb is it alright?
and jumpspl cannot execute and spl.ink too. How this flash?
Click to expand...
Click to collapse
What to do?
I bought a new device and when I tried to upgrade it with an unofficial ROM I couldn't do the step of upgrading SPL and the indicator stayed stop at 0%
My Device boot loader shows :
DIAM100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
I have tried all Hard-SPL Standard and Developers versions but I got the same result stopping at 0% including the RUU_Signed.nbh which is designed especially diamond came with 1.93 SPL originally
Please help me
fofo1881 said:
I bought a new device and when I tried to upgrade it with an unofficial ROM I couldn't do the step of upgrading SPL and the indicator stayed stop at 0%
My Device boot loader shows :
DIAM100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
I have tried all Hard-SPL Standard and Developers versions but I got the same result stopping at 0% including the RUU_Signed.nbh which is designed especially diamond came with 1.93 SPL originally
Please help me
Click to expand...
Click to collapse
You have Hardspl installed already. You don't need to overwrite it again.
Kevbodian said:
You have Hardspl installed already. You don't need to overwrite it again.
Click to expand...
Click to collapse
But also when I try to upgrade directly with any cooked ROM I face the same problem
the upgrade stops on 0%
Plz help me if u have any idea
THX
What you show is the shipped SPL - so you will only be able to use offfical (if branded) operator customised ROMs.
more info to follow... (just on the phone)
There is a sticky thread about this problem
http://forum.xda-developers.com/showthread.php?t=409425
Just a tip..read that and your problem is gone
fofo1881 said:
I bought a new device and when I tried to upgrade it with an unofficial ROM I couldn't do the step of upgrading SPL and the indicator stayed stop at 0%
My Device boot loader shows :
DIAM100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
I have tried all Hard-SPL Standard and Developers versions but I got the same result stopping at 0% including the RUU_Signed.nbh which is designed especially diamond came with 1.93 SPL originally
Please help me
Click to expand...
Click to collapse
If your phone shows this info after you flash hard-spl in your device, you dont have hard-spl in your device at all, so flash that first
you should seen 1.93Olinex forexample if u have flashed the 1,93unsigned hard-spl
R3PUBL1K said:
What you show is the shipped SPL - so you will only be able to use offfical (if branded) operator customised ROMs.
more info to follow... (just on the phone)
Click to expand...
Click to collapse
My device is not branded....
Do u mean that it will never accept upgrading to coocked ROMs ?
DO u think that there is no method yet ? or we will find new methods in the future ?
alas
fofo1881 said:
My device is not branded....
Do u mean that it will never accept upgrading to coocked ROMs ?
DO u think that there is no method yet ? or we will find new methods in the future ?
alas
Click to expand...
Click to collapse
No I am not saying that - If you dont have either OliNex or Jockeys HARDSPL then you could only use offical ROMs....etc etc...
So you really need to sort this issue out then you will be free to load any cooked ROM depending on your region
Remember that OliNex's SPLs have protection in them so that you can only update while you machine is connected via activesync.
When you try and Run the olinex SPL then you should get a popup on you devices screen asking you to confirm you want to run this application. Do you get this far?
Have you tried Jockys?
R3PUBL1K said:
When you try and Run the olinex SPL then you should get a popup on you devices screen asking you to confirm you want to run this application. Do you get this far?
Click to expand...
Click to collapse
I've done that but it was useless and I've got the same problem 0%
R3PUBL1K said:
Have you tried Jockys?
Click to expand...
Click to collapse
I have not heared about it also i couldn't find it in the forum
would u lead me please ?
fofo1881 said:
I've done that but it was useless and I've got the same problem 0%
I have not heared about it also i couldn't find it in the forum
would u lead me please ?
Click to expand...
Click to collapse
Try here JOCKY
omar 1958 said:
Before flashing Olinex Hardspl you need to do three things:
1. Download Net framework Compact from herehttp://www.microsoft.com/downloads/details.aspx?FamilyID=e3821449-3c6b-42f1-9fd9-0041345b3385&displaylang=en Connect device to pc and wait for Active Sync to finish. Now run the download and follow instructions, make sure to install to device and NOT to storage. Reboot your phone.
2. Download and install Cert_SPCS. (Attached).
3. Download and Install EnableRapi. (Attached). On installation of this, your phone might come with the comment that this file is already on the phone and installing this file will remove the old one, accept the new installation and reboot.
Having done the above, you are now ready to flash HardSPL. For further help read this http://forum.xda-developers.com/showthread.php?t=476738
Good Luck this time round.
Click to expand...
Click to collapse
Never had to this before - but I've never had any issues flashing Hard SPL to devices - over 50 different handsets
Hey, I gotta apologize for my above post. I read the 1.93.000 as 1.93.Olinex.
R3PUBL1K said:
Remember that OliNex's SPLs have protection in them so that you can only update while you machine is connected via activesync.
Click to expand...
Click to collapse
What do you meen? I have olinex1.93 and never use Active sync to flash a rom (or start AC), I put my phone in bootloader manualy and flash. Or is Ac startup even is this situation?
omaga said:
What do you meen? I have olinex1.93 and never use Active sync to flash a rom (or start AC), I put my phone in bootloader manualy and flash. Or is Ac startup even is this situation?
Click to expand...
Click to collapse
I was trying to explain that don't try flash (another) SPL using HardSPL as olinex one has overwrite protection.
Flashing ROMs this way is no problem - but not recommended
Upgrading is not possible
R3PUBL1K said:
I was trying to explain that don't try flash (another) SPL using HardSPL as olinex one has overwrite protection.
Flashing ROMs this way is no problem - but not recommended
Click to expand...
Click to collapse
I found that this new version of devices is HardCoded with original HTC-SPL
So its seems that upgrading to unofficial ROMs is not possible yet ...
thank u all for your concern
R3PUBL1K said:
I was trying to explain that don't try flash (another) SPL using HardSPL as olinex one has overwrite protection.
Flashing ROMs this way is no problem - but not recommended
Click to expand...
Click to collapse
I have Olinex 1.30 and have previously upgraded from ROM 1.34 to 1.93. However, I have tried upgrading the ROM to 2.03.831 but it doesn't work.
Do I need to upgrade the Hard SPL to 1.93 signed? Where can i get the file?
Thanks.
Hello,
try the "RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip" from THIS thread as this was the only one that worked for me. I recently flashed a O2 branded Diamond and was also about to give up...it was my last try/chance and eventually I succseeded in flashing any Diamond ROM until 100%.
...bye DonQ
does it means I have to overwrite my HardSPL 1.30 signed?
Got a new Diamond and same issue, can not hardSPL1.93 Olinex over this new original SPL 1.93.000
Hey I succeeded to work this out!!
Here's what I did:
Download this file: Unsigned-Hard-SPL-Diamond-OliNex.zip
and this: RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip (you can choose another developer version such as HardSPL_Olinex137_Unsigned.zip)
Now copy the file RUU_Signed.nbh of seconde archive to replace the one in the first archive. Then run the ROMUpdateUtility.exe of the 1st archive. As the moment the percentage bar appears, run the SSPL-Manual.exe of the 1st archive from your PDA (of course, this file must be copied to PDA before via ActiveSync).
Just run again ROMUpdateUtility.exe if you have a phone not responding error.
Then there you go...
4fun00 said:
Hey I succeeded to work this out!!
Here's what I did:
Download this file: Unsigned-Hard-SPL-Diamond-OliNex.zip
and this: RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip (you can choose another developer version such as HardSPL_Olinex137_Unsigned.zip)
Now copy the file RUU_Signed.nbh of seconde archive to replace the one in the first archive. Then run the ROMUpdateUtility.exe of the 1st archive. As the moment the percentage bar appears, run the SSPL-Manual.exe of the 1st archive from your PDA (of course, this file must be copied to PDA before via ActiveSync).
Just run again ROMUpdateUtility.exe if you have a phone not responding error.
Then there you go...
Click to expand...
Click to collapse
Ok now, I got the same situation as described above, but the phone's software won't boot. I can just put it in the bootloader mode. I cannot put the SSPL Manual file on the device. How do I reflash it then? USPL said that this version is not supported. Any ideas? Thanks for any input.