hey
i was following the first time flashing rom tutorial when and everything was going fine until i got to the cid/sim unlocker where after patching the radio and then doing step 3: unlock after completion my phone no longer boots and goes to a black screen
when i do a hard reset it will get through all the customization installing then shut right back down to a black screen
any help appreciated!
nevermind followed the wiki and fixed my phone
Good boy. They're gonna like you around here.
Related
Well I am a newbie and having a lot of fun upgrading until tonight.... I unlocked the mda vario and upgraded first with official t-mobile version then with the aku 3.3. My mda is a g4 and not cid unlocked, but I managed to load the aku 3.3 with the shelltool.... After I did everything the phone was a total brick... Could connect to pc, couldn't turn. The main page was coming up and giving the version of the mobile but wouldn't do anything else. So I tried pressing the call button and the wireless button and quickly pressed the reboot little button on the side. The screen became green and red, with something else written. When I did that and I tried to upload the software off t-mobile from http://www.tm-phonedownloads.com/download_manager_mda_vario.html, the software sort of recognized, than it asked to disconnect and take out battery. After I had to put back in and the usual start screen was coming up, but as the t-mobile software was asking if the red and green screen was up I repressed the call and wireless button and said yes. After that the phone was upgraded to the firmware off t-mobile and now is working fine again. It was scary though, so think twice before upgrading....
if you follow the instructions properly in the shelltool thread.
http://forum.xda-developers.com/showthread.php?t=293480&page=14
iv attached a tutorial on page 14 of that thread. you should be able to successfully upgrade rom
if anything goes wrong. boot your phone in bootloader mode and use the wizardlove rom to fix it.
i spent 7 hours last nite tryin to upgrade rom in which i mustve recovered my fone liek 6 times using the wizardlove rom
wizard love
yeah same here mucked my phone up the first time then read the instructions followed them and now running underground crossbow edition now have flashed rom about 3 times with different ones if you read the instructions works fine
wizard love saved my phone also
Greetings,
Can you tell me where would i get wizard love rom.
Thanks
hjkl;' why no delete?
hi if anyone can help thatll be greatly appreciated. I just bought an att tilt 8925, and well this is what happens. it boots up and goes into windows screen and then as soon as it goes into the main screen it vibrates a whole bunch of times and then just shuts down. can't get it to active sync to reflash because it wont stay on after it goes into the main screen any help would be appreciated!
Where did you buy this Tilt? Did this happen straight out of the box or have you already flashed it?
Search on how to manually get into boot loader and re flash; http://forum.xda-developers.com/showthread.php?t=383904
i bought it like that. the phone is in great condition. all features seem to work but i think the guy did a hackjob on the rom so it's not working right and im all new to trying to get it to work.
Since it's new... start with some baseline work.
1. Do a hard reset.
2. Record ROM and radio versions
3. If it comes up... consider loading the ROM of your choice.
I see you're new here so PLEASE read my signature.
Thanks,
Your best bet would be, download the OEM official Tilt ROM, Manually get into boot loader, then flash it. There are also other methods of flashing such as from your Sd card. The previous mentioned link has allot of answers.
okay i just tried entering bootloader but it wont get into the screen. i hold the camera buton and hold the soft reset button at the bottom of th phone but it just boots up normally. anything im doing wrong?
Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks
Be strong. I think it's only bricked when you can't power it on.
I have a poor net connection and not time atm. So a suggestion if you haven't already, search the forum for the word bricked. I'm sure this has happened before..
There are several tricks that people know so you might be ok. good luck.
Calihoe said:
Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks
Click to expand...
Click to collapse
Flash an OEM Rom/Radio Combo. Also it wont hurt if you already CID unlocked to to go ahead and flash a new SPL to it. Should fix any and all issues as your phone is still actually booting and Not bricked
Installing windows the 6.1 ROM from HTC's site worked. Thank you very much for the great advice. If I wanted to now put Dutty's ROM on my phone can I go straight to that, or do I need to restart the whole ROM flashing process(installing Jump SPL, Hard SPL and CID) ?
If you have unlocked it, just put duttys onto the SD card and rename the .nbh to KAISIMG.nbh
Put the phone into bootloader and install Its the fastest most successful method. No worry about a data cable coming out mid flash ( happened once to me....not fun )
Shouldnt have to install hardspl again ( or use JumpSPL )
Just make sure that if you are installing a WM6.0 rom that you have a WM6.0 radio. If not, the flashing process for the radio is the same ( rename to KAISIMG.nbh )
Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.
Calihoe said:
Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.
Click to expand...
Click to collapse
Go into bootloader. If your screen says hardspl somewhere near the top then you're good to go. Check which version because you can have radio problems if you use a WM6.0 spl with a WM6.1 rom. Most recent roms are WM6.1 so try HardSPL 3.29 or higher.
If you don't have hardspl, get it here for wm6.0 roms or here for wm6.1 roms.
many thanks, your advice with the links were invaluable. I read and read and read, but i guess i did not read enough. This site rocks.
Hi Guys;
I have a K-JAM (G3), I flashed it with (G4) rom by mistake; now it is stuck on bootloader screen with IPL 2.16 on the screen, After reading a number of threads I tried to flash original rom but some times it gives conection error and sometimes it continues untill it reach the progress bar on PC but the device screen still on RGB screen and after a while it gives connection error.
I can turn it off and when turned on it shows bootloader (RGB) immediatly. I tried hard reset but after I release the reset button it shows the RGB again
mm thats not good, this usually means you have bricked it, but sometimes recovery is possible.
Suggest you have a good look round this forum and do some reading : http://forum.xda-developers.com/forumdisplay.php?f=289 the wiki may have some info for you too.
If you have already tried to flash back a stock rom and it hasnt work, it aint good.
Not to rub too much salt in your wound, but if you had read the stickies on the above forum, you wouldnt have done it. But do read the stickies.
I will move this over to the wizard forum.
Problem Solved
First of all thanks timmymarsh for the reply.
I Kept searching and didnt give up, now my problem is solved thanks to the post by cochumbo
http://forum.xda-developers.com/showthread.php?t=321398
I followed the steps posted there and my K-JAM is flashed successfully and fully operational now
Kool, congrats and no probs
Hello, Well, tried to Unlock my HTC 8925. I went step by step tru the guide and I guess i did something wrong, I installed the HardSPL in the device and i got the SPL-1.0 olipof on the 3 color screen. I used JumpSPL1.56-KAIS
After that i proceded to install the Kraiser Unlocker and follow the steps, Step1 and i guess something went wrong there cuz at the end of the update f the ROM, the phone turned on and it gave me a Black screen, i tryed to hard reset it, it takes me to the main Screen and how to set up the phone, then it runs a couple windws prgrams and plop, black screen, =(
What should i do? How do i get it back to how it was and unlock this thing.!?
Thank you
when i get to the bootloader mode this shows up
KAIS1*0 MFG
SPL-1.0. OliPof
CPLD-8
i fixed it!
yay
HOW??
jopecarlos said:
i fixed it!
yay
Click to expand...
Click to collapse
The same thing just happened to me. Please tell me how you fixed it. Thanks!!