Hi there,
I'm going crazy with my Touch Diamond. Since I have it, I've tried to test every functions except for videocalls. Now that I'm testing it i get an error which (roughly) says "Failure on videocall; what do you wish to do?" and I get four options "Try again, Make a voice call, Send SMS, Send MMS".
Has any of you had the same problem? If so, little help?
I tried to search the forum, the web, I called the operator and was told that there is no special configuration needed (not surprised), and i still can't make a video call.
Thanks to you all
I have the original Portuguese HTC Rom 2.03.410.1
---
Updated:
I tried to change Connection settings for Sel. Networks to "TMN Internet", soft reseted, made a video call and worked.
Then I change it back to "My Work Network", soft reseted, made a video call and ... worked.
I don't know if this was a coincidence or not, but it solved my problem
Related
My TyTN II is no more than one month old. Radio and ROM are all stock and I never tried any custom ROMs nor did I install hardSPL on it. The problem is all of a sudden I can't make any calls. If I dial a number it just says Call Ended following with couple of silent beeps. If someone call me they got to my voicemail. The strange thing is that after couple of retries, it works, I can make a call but then after another try, it stops working again.
In all that time, sending and receiving SMS works normally.
And now the very strange part of the problem. If I switch to 3G mode, everything is ok. No problems at all. If I switich back to GSM only mode, the problem is back.
I've contacted HTC in my country (I'm somewhere in Europe ) and all they can say is, hard reset your phone and if that does not work, send it for repair.
I consider that a valid response and I'm about to do just that but before I go and erase all of my applications and settings from my phone (which will take me ages to get them back) I was wondering if someone has previous experiance with this sort of a problem and if it can be fixed without hard reseting the phone.
I have the same issue but when I turn G3 mode ON. I can not make call with auto G3 mode on (I have to try a lot of times to make a simple call). If I use only GSM its works ok.
Zol
I have the same problem, i cannot make a call on 3g network only on GSM. I took the phone to the service and they said i had to change the motherboard it costs ~335 EUR. F*ck
Can anybody tell me an alternative solution?
Hi,
I want to create a data connection over csd line on my htc kaiser.
I wrote a simple software using tapi. This software run on htc s710 but it don't work on htc kaiser. I set the phone to use only 2g as written on securegsm site but nothing is changed.Htc kaiser is able to make outgoing data call, my problem is only with incoming call.
I also tried to change radio version but nothing...
I see at log and there is no at+cring message.
Please help me.
busa.andrea said:
Hi,
I want to create a data connection over csd line on my htc kaiser.
I wrote a simple software using tapi. This software run on htc s710 but it don't work on htc kaiser. I set the phone to use only 2g as written on securegsm site but nothing is changed.Htc kaiser is able to make outgoing data call, my problem is only with incoming call.
I also tried to change radio version but nothing...
I see at log and there is no at+cring message.
Please help me.
Click to expand...
Click to collapse
Did u solve that? I encountered the very same problem on Polaris. SecureGSM doesn't work either. They say HTC Polaris needs "professional setup" to work properly, that means mail your phone and money to them and wait.
Is it beacuse of the radio stack or RIL implementation?
Well i looked to see for any solutions but cant find any, i dont now if its a setting problem or if its a malfunction but i cant make any out going calls but i get all incoming calls, i can send sms's but not make a call.
try this : start>settings>personal>phone>services
get settings for call barring, you'll see the incoming and outgoing call settings (both should be OFF by default)
if that dosen't work, maybe you could post some more info like the message you get when you dial out, ROM & radio version etc...
Didn't forget to pay your bill, did you?
I had a similar problem with my Orange TyTn 2.
Although i could not recieve incoming either.
I had previously flashed the ROM and radio to a HTC's current 6.1 from thier website.
I tried reflasing the radio to lots of different versions but still no joy.
In the end i sent it back to HTC and they replaced the main board, under warranty, thankfully.
Hopefully it is just a setting for you.
well i did that and they were off soo i just did a hard reset and it works now but its quite a big annoyance and if it happens again ill have to switch my kaiser cause its just unacceptable
hi, i have a tytn II , when i make a videocall to any device who supported 3g this answer me like a voice call. And if any device want make a videocall to me - the dial signal is present, but I don't see anything(incoming ring or any action) on my device . please help me, cause i cant find any solve to my problem !!!!
What location/operators?
At my place until recently 3G video call was only supported when staying on the same network, i.e you could not place a video call to someone on a different network than you. I'd check with the operator, or try putting your SIM in aonther phone and try again to see if it's really due to the phone or not.
i tried to change the SIM and it not give me any changes. i try to make a video call to device who is in the same network "MOLDCELL". in my country exists another network that suport 3G "Orange" and I try the same thing, result is the same.
may be is a bug in my ROM(1.27.12.32) ??? maybe a must do change it ?
i tried to put my SIM in another device and its OK, i can make a videocall, result that the problem is in my device. Have somebody any ideas?
I solved this problem.... i installed wm 6.1 and videocalling is work
Hello everyone,
I already posted a question in another existing thread, but I couldnt get an answer so far.
My Problem is the following:
I have the HTC Kaiser, I bought it unlocked on ebay and put a AT&t Sim Card into it. Everything works fine but it wont vibrate on Text messages. It can play a sound on text messages and it can vibrate on phone calls but not on new Messages. Ive been to the Sounds and Notifications menu multiple times but everything is set on vibrate. I also downloaded kaiser Tweak, but there is only an option for sent Notifications.
I hope You guys can help me!
I have that too!
I have a tilt with the att branded 6.1 rom on it, and it would often reset the vibrate setting to no vibrate on text messages. Usually my own override lasted as long as I didn't reset the machine.
I assumed it was my company's activesync settings, but now I'm not sure. I'm reflashing it and will do the soft reset on the bottom when it says 3 (EDIT - it doesn't seem to work on the 6.1 distro) seconds until it's ATTified, and will try the official patch for the backlight hotfix (plus probably some tweaking from http://www.wmexperts.com/articles/howto/how_to_customize_your_tilt.html ). Hopefully this will fix it...
hello,
thank you for your anwer.
please let me know if it worked aftewr you tried it.
Actually, so far so good, the official re-image with the htc patch and playing with some kaisertweak settings (probably unrelated) corrected the no-vibrate issue. I'm seeing text that I type in the screen on IE not show up anymore though (think typing in to google search and not seeing what you typed), so I'm thinking of trying it kaiser-tweak-less. Also, when sending/receiving email, the status menu at the bottom is more often missing. I'm hoping these issues are all software and not hardware.