Hello,
Iam daniel. My english is not zo good but i will try.
I have flashed my phone with hardspl 3.56.
After that i installed wm6.5 from josh Build 21198
Then i start up my phone and every think look richt.
Then my phone ask for a restart, zo i start up and there was my problem, he doesn't start up.
I see thee first screen with red letters at the bottom and he does nothing.
Can you help me???
Have you tried a hard reset?
Also, did you CID unlock your phone as well? I believe you have to be CID unlocked to flash a 6.5 ROM on your phone.
Had a same matter last day ago, after re-flash, all working fine
I didn't unlock my phone whit cid...
for a hard reset is it the two buttuns (with the lines on it) near the phone buttom?
And a reflash how does that work?
I have no communication with my pc know because he crased in the screen when you starting up. It is the first screen you see when you restart your phone.
Ok, a couple of things... this is the wrong forum to be asking in, and I bet a mod is going to shut this down at some point. You should try posting in the forum for the ROM you flashed.
What you need to do is grab a stock WinMo 6.1 ROM and flash via the SD card method, that should get you up and running again.
Then, you will want to run Olipro's SIM/CID unlocker. What this will do is fully unlock your phone so you can flash any ROM, radio, SPL, any! Be careful, though, since not all ROMs are meant for Kaiser... so make sure you are flashing stuff meant for Kaiser.
Once you run Olipro's unlocker, you will want to re-flash the 3.56HardSPL, then a new radio, then go ahead and start flashing any ROM from the Kaiser section.
WinMo 6.5 ROMs reqiure you to be CID unlocked, and that is why you are stuck where you are.
And yes, you are right with how to do a hard rest.
Thanks! I try this tommorow if it works, if it doesn't work i will post my problem in the forum for rom. But hopfully it works because if cot know a nokia 6500 and i can't without my qwerty
Related
Hi, After the soft reset comand, I removed the battery from my Wizard. After that the followin problem was appear: the phone is bringing up to the splash screen and STOP on this position.I have tried to download another Rom but the problem still is the same. My Phone is not CID unlock and before this, I cooked own rom like is writen here http://forum.xda-developers.com/showthread.php?t=271043 . So any idea how to wake-up my phone MDA Vario.
Ok forgive me if I'm wrong here, I don't really want to judge before I know the full story, but seems to me your brain went on strike momentarily. First rule of flashing any unofficial rom CID UNLOCK YOUR DEVICE. Anyways sorry, I just wanted to say something so it doesn't happen to you again, that said, what rom did you try to upgrade to? what rom did you try to downgrade to after that? is your device a G3 or G4?
If your device is a G3 I would recommend downgrading to this rom by xelecin
ftp://xda:[email protected]_RUU_Wizard_1081002_108_10910_ENG_US.exe
it will ask you if you want to CID unlock your device at the start so you shouldn't need to worry about forgetting this time , if you can't connect your device to activesync just go into the bootloader (hold the camera, voice dial buttons while pressing the reset button) and once it connects run the set-up.
Oh another thing before I forget..... do some searching and read up a bit, because this is a pretty common topic on this forum, best of luck and hope everything works out ok. If not, report back.
*edit* I just noticed the thread that you linked to, I actually wasn't aware that this was possible, but anyways I think it's still much safer to CID unlock your device if possible, and another thing you might try replying in that thread if it doesn't work out since they should be more knowledgeable in the matter..... and that would help keep the forums less cluttered *edit*
Thanks, for your help, Unfortunately you are totaly right for my stupid act (again). At first i tried to solve the problem alone , but whole day I roam through this forum to find solution but I can't find the same problem like my. Maybe because of my ..... brain .Anyway I am with G3. NOW I have
IPL 1.0
SPL 2.26
GSM 01.09.11
OS 1.5.4.2
This is after this procedure http://forum.xda-developers.com/showthread.php?t=263116
I tried also to download also and Molski's 2.26.10.2 AKU2.3 Rom a.k.a. 2.26.10.2 Final Edition Rom, but the problem is the same : The splash screen is running and STOP and.... nothing.
I can go to bootloader and can download new rom, but I can't start fhe phone.
Yeah I know these forums aren't the easiest in which to look for info. So you can go into the bootloader, that's good. Don't try to go to a AKU2.x rom or later, keep it under that, so no 2.26 roms at all. 105, or 108 roms should be good.
Did you try the rom from the link I provided or the one on the thread? and afterwards did it go into the phone at all? My friends MDA had a similar problem last week, caused by the same thing, though in your case I see the SPL isn't updating when you install new roms on his it was the os that wasn't updating, but as soon as I installed that rom I recommended it booted up fine, then I updated his device to molski's 2.3.
I'll check back in a few so let me know how's it going.
Here's what you need to know & if you follow these instructions your prob will be solved.
The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
http://forum.xda-developers.com/showthread.php?t=285435
Wish u best of luck.
DoCtOr_X said:
Here's what you need to know & if you follow these instructions your prob will be solved.
The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
http://forum.xda-developers.com/showthread.php?t=285435
Wish u best of luck.
Click to expand...
Click to collapse
Ok, but tell me how to solve this :
"qiote"
8. Open ActiveSync, Explore and copy enablerapi.cab from your PC's C:\ (remember that's where you extracted lokiwiz to...) to you device, I don't care where.
9. Pick up your PDA, File Explorer, find the enablerapi.cab and click it.
"quote"
I don't have access to the phone explorer and phone at all.
masr1979 I have tried the rom you give me, but it look like there is some things I don't understand: When I start the exe file i have choice <continue> .Whet I type <c> 2(two) time the soft tell me <no device found> and order me to continue with copy ???. After few seconds tell me that Unlocker ..... Done!, and start HTC wizard Unlocker and NOTHING !!! Stop on this position more then 15 min. and only the led for charging on the phone is active.
Forget all about unlocking. Until you can boot the device completely it'll never work.
Try and install an official 2.x ROM on your device.
My suspicion is that you originally has a G4 device, which is bad because if you DID have a G4 you have a brick now...
Can you remember your phones old ipl/spl? for your sake I hope it wasn't something in this format 2.XX.000X.
masr1979 said:
Can you remember your phones old ipl/spl? for your sake I hope it wasn't something in this format 2.XX.000X.
Click to expand...
Click to collapse
Of course I'm not sure, but I thing it was 2.21. Anyway did you think that is posible to cook my own rom in G4? I'm totally confused.
Every time when I upload new rom I have this:
http://forum.xda-developers.com/attachment.php?attachmentid=32884&stc=1&d=1168184491
IMG_2976.jpg
...and also this is my bootloader screen
http://forum.xda-developers.com/attachment.php?attachmentid=32885&stc=1&d=1168184491
IMG_2977.jpg
Dr Puttingham said:
Forget all about unlocking. Until you can boot the device completely it'll never work.
Try and install an official 2.x ROM on your device.
My suspicion is that you originally has a G4 device, which is bad because if you DID have a G4 you have a brick now...
Click to expand...
Click to collapse
Thanks, but I try to find oficial rom but without success. And very interesting thing I found.. when I start to upload new rom the soft start to check my old rom and after that tell me that i have GE (german) language, but my old was WWE ?
Is it posible some one to give me some link to official 2.x ROM but for T-mobile german language.
Well the other day I tried finding that german rom for a while.... that search was going nowhere, I saw this thread, I don't know if you might want to check into it and maybe try it out. There's mixed results apparently but who knows
http://forum.xda-developers.com/showthread.php?t=276963
Well I would like to get another software because the orange software is pretty much the worst one you can get.
I’ve been trying to update from wm6 to wm 6.1 but I had to hard reset my phone many times cause whenever I try to flash the rom, I get that white screen that stay at 0% during the whole process to finally see an error not on the devise but well from the software (running on vista).
Please help!!!!!!
few things to remember befoe u do anything to ur phone:
1) read kaiser wiki
2) from wiki follow links on how to flash hardspl on to ur device.
3) go to kaiser rom development forum and read the first sticky containing info about flashing.
flashing hardspl will cid and sim unlock ur device.
Plz do read and search or u will mess up ur toy.
isn't there an issue with flashing orange ones something to do wit the radio and not to change it? I want to flash mine but the wiki isn't too clear on orange versions
doesn't matter what stock rom u have, once hardspl'ed u can flash any rom/radio u want to ur device.
just make sure radio works w/rom u flash. alot of chefs include radios w/their roms and ones that don'zt will tell u which radio works with rom
technocat said:
isn't there an issue with flashing orange ones something to do wit the radio and not to change it? I want to flash mine but the wiki isn't too clear on orange versions
Click to expand...
Click to collapse
I've flashed my Orange TyTN II with no problems. So long as it is unlocked to all networks it should be OK. However if you do it then your warranty goes out the window.
Run HardSPL first
Once it is installed, double-check that it is installed by doing the folowing:
Power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-color screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
If it does not say "SPL-1.0 OliPof" then HardSPL is NOT installed.
Once HardSPL is installed you can then run jockyw2001's unlocker to unlock the phone to all networks.
Then you can flash ROMS like there's no tomorrow!
nice walkthrough mate what's the differences between the roms just peoples personal customisations? is there a huge difference from the orange version?
the chefs cook whatever they want into the different roms..basically just personal stuff or needs...so read what posts and see which one fits u most...if not...try some out and see which one u like...
Narfy, go over to read this thread ... it is one man's story of getting his Orange unlocked and 'sorted'
http://forum.xda-developers.com/showthread.php?t=386089
With an happy ending
Ok having problems trying to unlock my orange tytn2. Hard SPL is installed, Step 1 of the kaiser simunlocker has been done and verified. Following the instructions, I have reset the phone to boot screen and went to step 2, step 2 of course is a command and in xp this closes as soon as you open it. Have went to command prompt to run step 2 and it gives an error about unable to connect to usb: cannot connect to \\.WCEUSBSH001
Anyone any ideas am now stuck lol.
please ignore sorted now helps when you actually read forums lol
Hi
I have a UK orange Diamond which has been unlocked using the legendary Oli unlock method....
Can I put the UK orange HTC ROM upgrade directly on this and will the handset still remain Sim unlocked?
I am on T-Mobile UK and want to make sure I can continue using this without a brick!
also is there a good method of backing it up?
are there any alternative ROM updates which anyone would recommend in this situation?
Thanks all
If your Device has Hard-SPL installed on it, you should be able to flash any ROM without any problems.
If your device has been SIM-Unlocked, do whatever you like it will remain SIM-Unlocked. Even if you flash a new ROM or even Radio ROM it will stay SIM Unlocked.
To backup messages, contacts, etc I recommend you use PIM backup.
But anything on the 4GB storage doesn't get wiped off anyway.
And about bricking your device...apparently Hard-SPL is meant to be a lot safer than the Stock-SPL because if you screw up your Flash you can just go back to the Hard-SPL and flash a new ROM, overwriting the corrupted one.
Thanks for that,
Silly Q but how do I know if Hard SPL is installed? I know the unlock method required installing something...
Im scared of doing this as I have bricked in the past my HTC Kaiser! lol... dont want to make this mistake again!!
Lol don't worry about it, I even freak out when installing official updates.
Flashing ROMs still scare me and I have been using and flashing PDAs since 2005!
To make sure HardSPL is installed, Go into Bootloader mode on your HTC Diamond.
I think its the Soft Reset Button + Volume down button.
Hold the Volume down button and quickly press and let go of the Soft reset button, whilst holding the volume down button until the bootloader menu comes up.
If you have HardSPL installed, you should see something along the lines of 'Olinex'.
As far as I know, if you used Olipro's unlocker then you must have installed HardSPL in the processess anyway, but best to be sure!
Thanks for the info, It does say OliNex on it so im flashing now....
still on 0% .......
only been 3 mins tho, so patiently waiting...
How did the flashing go?
got there in the end mate
had to put the HARD-SPL developers version as the official orange rom would not go past 0%..
was scary but its working a treat now!
thanks a lot for your help
Glad you got there in the end
Enjoy your HTC Diamond
Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks
Be strong. I think it's only bricked when you can't power it on.
I have a poor net connection and not time atm. So a suggestion if you haven't already, search the forum for the word bricked. I'm sure this has happened before..
There are several tricks that people know so you might be ok. good luck.
Calihoe said:
Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks
Click to expand...
Click to collapse
Flash an OEM Rom/Radio Combo. Also it wont hurt if you already CID unlocked to to go ahead and flash a new SPL to it. Should fix any and all issues as your phone is still actually booting and Not bricked
Installing windows the 6.1 ROM from HTC's site worked. Thank you very much for the great advice. If I wanted to now put Dutty's ROM on my phone can I go straight to that, or do I need to restart the whole ROM flashing process(installing Jump SPL, Hard SPL and CID) ?
If you have unlocked it, just put duttys onto the SD card and rename the .nbh to KAISIMG.nbh
Put the phone into bootloader and install Its the fastest most successful method. No worry about a data cable coming out mid flash ( happened once to me....not fun )
Shouldnt have to install hardspl again ( or use JumpSPL )
Just make sure that if you are installing a WM6.0 rom that you have a WM6.0 radio. If not, the flashing process for the radio is the same ( rename to KAISIMG.nbh )
Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.
Calihoe said:
Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.
Click to expand...
Click to collapse
Go into bootloader. If your screen says hardspl somewhere near the top then you're good to go. Check which version because you can have radio problems if you use a WM6.0 spl with a WM6.1 rom. Most recent roms are WM6.1 so try HardSPL 3.29 or higher.
If you don't have hardspl, get it here for wm6.0 roms or here for wm6.1 roms.
many thanks, your advice with the links were invaluable. I read and read and read, but i guess i did not read enough. This site rocks.
Hi, I have been reading this forum for some weeks and I am thinking of unlocking my Touch 3G by using this Hard-SPL thing which is available here.
However I am still hesitating because I have never done such an "intervention" in the past, so please allow me to ask you if you did it and if yes if it worked without problems (from the thread I wasn't able to understand if more that 2-3 people have really succedded!)
Thanks, lila
I actually tried few times yesterday and today, but I am getting "Server is down" message .
i manage to solve it. how? i have exit my antivirus, then, go to control panel/windows firewall and put it on off, and will work. each time, i have install enablerapi.cab on device memory.
I disabled firewalls and antivirus software. I tried on three different computers with different (working) access to internet. Still no joy . I guess I will try later.
I've unlocked my Jade without any problem, but to be honest i didn't flash another ROM yet because i want to be sure i can go back to original one (just in case of waranty), and i don't know how to rebuild my dumped original ROM.
I'm still trying to figure this out, gonna succeed as long as i keep reading this excellent forum.
Anyhow, flashing a new ROM isn't that difficult, but you have to follow the guidelines very well and keep on your reading glasses..)
Hi. I am very happy Thank you OLINEX. I have HTC 3G (Jade 100) I make HARD SPL and I install http://rapidshare.com/files/15981107...30.09_Ship.exe
rom. It is very good rom and stable. Now I have english language and my phone rings best. Thank you OLINEX.
fenikso said:
I disabled firewalls and antivirus software. I tried on three different computers with different (working) access to internet. Still no joy . I guess I will try later.
Click to expand...
Click to collapse
So, I finally got it to work. I will post my "story" to Hard-SPL thread .
i did it with the first attempt with v3, no problem and i'm really happy
Hard-SPL
With hard-spl you will not unlock your jade . It´s only necesary to upload others roms to device.
estancolaplaza said:
With hard-spl you will not unlock your jade . It´s only necesary to upload others roms to device.
Click to expand...
Click to collapse
Oh yes you are right, however that's what I meant; in fact I have a Jade with French ROM and I want to change it to English.
for me dont work the hard spl....
I've been trying for the past 3 days to Hard SPL my jade without any luck. always the phone restart without entering to tri color mode.
I even tried to exit the antivrus and disable the firewall but always same error.
Any suggestions here please?
fenikso said:
So, I finally got it to work. I will post my "story" to Hard-SPL thread .
Click to expand...
Click to collapse
Ca you post your story please maybe you can give us a little help.
Thank you
no luck with the one i tried, just restarts. dont know why this phone is so special, every other one ive done is so easy.
stock loader version is 1.40.707.2 tried using windows xp sp3 .net3.5, tried using hardspl v2 and v3 (tried v2 just in case that worked)
the link is dead!!
lots of problem, the HardSPL from Oli doesnt work, but the radio update from HTC works
keep trying and win
SPL does work. But you must keep trying. I got "server down"
and so on. After a week and hundred times try, I got unlocked the phone.
Now I can enjoy any wm6.5 roms. It is free software and not perfect.
But It does the job . well done Olipro and Cmonex.
Which phone do I have ?
My phone is supposed to be a Touch 3G but the processor is a Marvell PXA310 @ 624 MHZ.
The phone says it's a T3238, can someone tell me which phone I have please?
It's a clone I think.
When I boot holding the volume key I get a white screen saying USB update model
Hi,
I have a TOUCH 3G and I did the HARD-SPL. The better thing in here is that developers and always available to help you. For example, i had some problems doing hard-spl to my Jade but with the help of cmonex(developer) i've done it without any problems. You have a lot of support in here. SO, If I were you, I would do it.
it works like a charm
hi
Yes i did my HSPL today and it worked like a charm it was so easy and
i had a gene(P3400i) and the HSPL for this phone was so difficult
compare to the HSPL for Jade
the Jade HSPL took only around 10-15 mins
now i need to flash some cooked rom will do it today right now downloading ironegles ROM
Note : u need to off ur Firewall or it wont work OK