[HELP] Phone Off in ROM 1.57.831.1 (47324) - Touch HD Windows Mobile ROM Development

Hi everybody
I've upgraded my BlackStone to ROM 1.57.831.1 (47324)
But After the complete proccess, the function phone is off.
I can't active the phone.
could somebody help me with this?
Thanks....

have you hard spl version 1.14 your phone ? try to upgrade to hard spl 1.56

dmonium said:
Hi everybody
I've upgraded my BlackStone to ROM 1.57.831.1 (47324)
But After the complete proccess, the function phone is off.
I can't active the phone.
could somebody help me with this?
Thanks....
Click to expand...
Click to collapse
Do you have any other symptoms i.e. green screen issue?
Sounds like you haven't used USPL or HSPL before upgrading rom. 2 main symptoms are phone function not working and green screen/distortion issue.
If you follow cRaCKwHoRe's guide (see my signature) you'll be fine

[SOLVED] Phone Off in ROM 1.57.831.1 (47324)
thanks friend
I can fix the problem
I needed the hard spl 1.56 for this ROM.
Now, The BlackStone is operating excellently

Related

HTC P3600 don't want to flash!

Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
no ideas guys?
so no one can help me with an idea???
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
jackkkkk said:
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
Click to expand...
Click to collapse
it's a P3600
Do a hard reset and flash an OFFICIAL ROM from SD-card
Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.
thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software?
If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.
nightblade said:
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
Click to expand...
Click to collapse
Make sure that your SD card it out

New Official ROM Upgrade- Release Date: 2009-04-14

I've tried to download the ROM, but HTC tell me this "Sorry, this software download is not suitable for your device".
Maybe my device s/n number is not correct.
Maybe someone who has the correct s/n could download this ROM~
Just tell you guys the news~
http://www.htc.com/europe/SupportDownload.aspx?p_id=174&cat=2&dl_id=537
Caxio's and frednd's DownLoad Link--(I wanna say THANK YOU VERY MUCH!)
See page3 #21 & #23
Filename is :
HTC Touch 3G_MR2009_RUU_Jade_HTC_Europe_2.32.401.2_Radio_Sign_12.41.30.16_0.41.30.12_Ship
edit:
on booting the last red line (after radio and protocol) now says :
D 2.32.44800
Date (which shows after first boot) after screen calibration is now set to 25/03/09
(in settings / about) Build : 5.2.20771 (20771.1.4.6)
(in settings / device info) : rom version 2.32.401.2(44800)
ON customization after first boot if scaned for wifi networks and poped up a message about available networks
Ht845kh14923 :d
o2p63 said:
Ht845kh14923 :d
Click to expand...
Click to collapse
This is for italian version.
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
It seems HardSPL 1.40oli and this 2.32 rom don't work very well.Very sluggish and phone can't turn ON even after 2 Hard resets.
What is your experience???
Do not install if hard spl
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Could anyone check, if the gps-support has been improved?
km
lexx2009 said:
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Click to expand...
Click to collapse
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
update : Jade is fine now. New SPL is 2.32.0000 . More testing to be done.
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
lagoskon said:
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
Click to expand...
Click to collapse
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Myster said:
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Click to expand...
Click to collapse
This is on the Hard-SPL page along with the Oli version
http://forum.xda-developers.com/attachment.php?attachmentid=166262&d=1236988725
GPS seems to work fine now, also the scroll behavior of opera is better
km
It is annoying that hardspl doesnt work with this upgrade of jade.. can't built a rom now with the new oem. It's all newer than the iolite versions, but still doesnt include Footprint
Any changes in Manila? New tabs? Calendar? Stocks? Changes in the contacts?
Hi
What is the Radio version in this new ROM?
I have just applied the version from here and if this contains the old Radio then I can hold off for now until hopefully a compliant Hard-SPL is made, I can live without Opera being perfect.
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
nereus114 said:
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
Click to expand...
Click to collapse
Install a different rom from this forum-> Shut down your jade, unplug it. Hold down "volume down button" and ""power on button" to get in to boot mode. now start to flash another rom.
when finished you can install stock spl and then install this new rom
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
jarel said:
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
Click to expand...
Click to collapse
that's right.. but i think it's in one of the drivers. using the old drivers and the new oem/sys makes it possible to run it with the current hardspl.
radio in this rom 0.41.30.12
no changes in manilla tabs, don't know what changed but it's newer

[HELP] Strange screen issue

Good morning,
im opening a new thread because i didnt find an answer for my problem.
I got my Blackstone running with HSPL1.56+ olinex, 1.17 radio and using different roms like dutty or miri ones... so everthing works fine since I tried to flash the new dutty rom holy grail R2... after that my screen s displsaying the colours wrong like in 256colours graphic. some colours like green and purple are flickering...
I tried to change from HSPL to USPL but it wont help...moreover i flashed the USPL and flashed with 1.56 stock rom without success
dont know what to try
thanks in advance
zwon
Mybe a coincidental hardware problem... but just a guess!
Use my mobiler and see what the phone looks like on your PC?
or is it wrong rom... i gess is about grafick try to put out batery thehn back turn on then when boot do soft reset i have smilary problem
afr33s said:
Mybe a coincidental hardware problem... but just a guess!
Use my mobiler and see what the phone looks like on your PC?
Click to expand...
Click to collapse
i think so too
hm on my pc its looking good...
gagi75 said:
or is it wrong rom... i gess is about grafick try to put out batery thehn back turn on then when boot do soft reset i have smilary problem
Click to expand...
Click to collapse
i think not because i flash roms which i got working before
take out battery i tried a few times...last night my hd had no batt^^
i wos instal ok rom but each time when i do reset he goes off he wont start then i remove batery off then put back and start he goes up then when i see on screen smart mobilty is write tu soft reset and is ok all.i have thet problem and solwed...do what i do meybe help
sory for english
Update your hardspl to version 1.56
Does your SPL match rom, i.e. if a rom based on 1.56+ you need HSPL 1.56
Fallen Spartan said:
Does your SPL match rom, i.e. if a rom based on 1.56+ you need HSPL 1.56
Click to expand...
Click to collapse
yes i tried... flashed the hspl 1.56+ before and using it with the equal spl version but wont fix my screen
i tried a many different solution but nothing would solve it
flash to stock rom, revert spl to stock and reflash stock rom.
use the newest stock rom available, after that HSPL again and everythings good to go.
have a look at the wiki, the problem is described pretty well.
regards
meska said:
flash to stock rom, revert spl to stock and reflash stock rom.
use the newest stock rom available, after that HSPL again and everythings good to go.
have a look at the wiki, the problem is described pretty well.
regards
Click to expand...
Click to collapse
sure? than sorry.. dont saw it
ill give it a try
meska said:
flash to stock rom, revert spl to stock and reflash stock rom.
use the newest stock rom available, after that HSPL again and everythings good to go.
have a look at the wiki, the problem is described pretty well.
regards
Click to expand...
Click to collapse
how to revert to stock spl?
ok find it by myself....would 1.54 be recommend or later? or could you even post the url where i find this in wiki??
dont find it
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Rom156
have a look under the greenscreen section... 1.54 will just be fine.
Options if you have Olinex 1.14 HSPL installed then installed a 1.56 rom and now have greenscreen
* (Not recommended) Revert back to stock SPL (using Restore-SPL-1.xx from HSPL thread)
* Update HSPL to 1.56 (After flashing HSPL 1.56 your device will reboot and the greenscreen problem is gone.)
* Or Use USPL 2.5
or send me a PN i can help you via ICQ even in german.
regards
meska said:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Rom156
have a look under the greenscreen section... 1.54 will just be fine.
Options if you have Olinex 1.14 HSPL installed then installed a 1.56 rom and now have greenscreen
* (Not recommended) Revert back to stock SPL (using Restore-SPL-1.xx from HSPL thread)
* Update HSPL to 1.56 (After flashing HSPL 1.56 your device will reboot and the greenscreen problem is gone.)
* Or Use USPL 2.5
or send me a PN i can help you via ICQ even in german.
regards
Click to expand...
Click to collapse
so i tried this with all 3 kinds of stock spls...1.54 even too but it wont work
seems to me as it would be an other problem as the Greenscreen issue
yeah would be nice if you could help me with that tomorrow
ill add u in icq

[Q]please help downgrade new topaz from wm6.5 to mw6.1

hi
i thought that wm6.1 is faster than wm6.5 so after hardspl flash my new topaz with wm6.1 rom but it didn't start .after soft flashing and rest just shows startup picture and restart again .so i had to reflash it to wm6.5.
the question is how can i use wm6.1 and???
thanx in advanced
farzad23 said:
hi
i thought that wm6.1 is faster than wm6.5 so after hardspl flash my new topaz with wm6.1 rom but it didn't start .after soft flashing and rest just shows startup picture and restart again .so i had to reflash it to wm6.5.
the question is how can i use wm6.1 and???
thanx in advanced
Click to expand...
Click to collapse
I think you would need to downgrade your SPL.
So you would need to reinstall SSPL, then just install HSPL 1.83, then the 6.1 ROM. You will probably have "commercial use" issues to reinstall 1.83 so I would send the Olinex team an e-mail first before trying.
thanx Bruce Inman for u'r reply.i'm waiting for
hi Bruce Inman
I did what you said before.downgarde hard spl to 1.8 ver and then flashed my topaz with wm6.1 cocked and stock but didn't work. in boot session reboot cycling occur.
downgrading spl is not necessary i think, because i have also downgraded 6.5 to 6.1 last week, and my topaz got the latest hspl. last year i downgraded my kaiser to 6.0 and 6.1 with the latest spl.
i think the rom image you acquired is damaged, try re-downloading it
@Carrier
hi
i tested many rom cocked and stock .when i bought this damn topaz it was wm6.5
i think all fu... HTC are slow ,unstable .
I tried the same my self with official ROM from HTC. I didn't have to downgrade SPL because my phone for some reason is unable to be flashed HSPL Olinex ??
Operation run smoothly but after finishing topaz entered a constant reset loop after boot screen
I run out of ideas ...

Help with upgrade to WM6.5

Hi all,
please if someone can help me solve problem.
I got few days ago Touch Diamond2. It has WM6.1 ROM on it. I tried to upgrade with official ROM from htc.com to wm6.5 but it hangs on 18% with error "communication error". Phone turned on in recovery mode. After that i tried flashing with custom roms but no luck again. It hangs on HTC screen when booting and nothing happens. I flashed it back with shipped 6.1 ROM from HTCpedia and it started normal.
When i start it in boot load mode it states 1.33 Olinex SPL. Do i need to put original hardSPL before upgrading to official ROM or there is something else i am missing?
Tnx in advance
Borna_bkpdata said:
Hi all,
please if someone can help me solve problem.
I got few days ago Touch Diamond2. It has WM6.1 ROM on it. I tried to upgrade with official ROM from htc.com to wm6.5 but it hangs on 18% with error "communication error". Phone turned on in recovery mode. After that i tried flashing with custom roms but no luck again. It hangs on HTC screen when booting and nothing happens. I flashed it back with shipped 6.1 ROM from HTCpedia and it started normal.
When i start it in boot load mode it states 1.33 Olinex SPL. Do i need to put original hardSPL before upgrading to official ROM or there is something else i am missing?
Tnx in advance
Click to expand...
Click to collapse
updating your Hard-Spl to HSPL 1.83 first ! in order to flash WM 6.5 rom or custom rom
Hi and tnx for quick answer.
Just to confirm. I need to update even if I want to flash official WM6.5 rom from htc.com?
Borna_bkpdata said:
Hi and tnx for quick answer.
Just to confirm. I need to update even if I want to flash official WM6.5 rom from htc.com?
Click to expand...
Click to collapse
I think it could, try it !
Doesn't the official WM6.5 ROM update include an embedded SPL though? Although if flashing from official ROM to custom ROM or vice versa you'd definitely need to update HSPL.
netrial said:
Doesn't the official WM6.5 ROM update include an embedded SPL though? Although if flashing from official ROM to custom ROM or vice versa you'd definitely need to update HSPL.
Click to expand...
Click to collapse
Please Read Carefully the instruction for installing HSPL 1.83 or better to upgrade it to 2.51.OliNex.Make Sure U Have a internet connection on as hspl needs internet to install.

Categories

Resources