I've installed Softick Card Export II v2.12 in order to get a useable mass storage device.
There was a message that I should not run Card Export before I soft reset device, which I did.
BUT, big but, there was O2 logo, then WindowsMobile logo and then light turned off..five minutes later the Windows logo was still on the screen and my Wizard cannot boot up system completely. Holding Power button doesn't do anything,so I had to press that small Harr reset button. I tried one more time, leavin the phone on for 15 minutes, but the story was the same..Windows Mobile..and nothing else. Even keyboard and green/red button stopped being lit.
I can hear on my speakers that the phone is working (electric iterference).
I thought I could just put new ROM over it, but then saw that I need a working ActiveSync connection in order to do that.
Please, does anyone have an advice on what to do?[/url]
Any 3..4..5 button-combinations that could reset the device and format internal memory?
Hold VoiceDial + CommManager button and press the soft-reset button, then press the Send button (Green button) to hard-reset your device.
Why did you install v2.12 because v2.17 is already released?
It's better to install WM5torage 1.60, it does the same and is freeware and works A LOT better!
Thanks a million!
I've been using HDIII 19 for a week and now my phone started acting weird: when I press sleep button camera turns on after couple seconds, call buttons and soft keys are not working until I don't press windows ,e-mail or internet button, camera button is not working. I tried to reinstall ROM but now I cant do hard reset. Also QWERTY keyboard is not working until I don't press windows, internet or messaging button. Can anyone help to fix this problem, I tried to install other roms but nothing changed.
So all my physical keys on my xperia x1 including the Volume button, the ok button, the X panel button, the pick up call button, the end call button, the two silver buttons all don't work. None of the keys on my keyboard work either.
I've been trying to hard reset but every method I've found includes holding down the volume button (which doesnt work since that button is unresponsive). I've tried the 2 silver button method along with the poking the stylus in the hard reset hole in the back of the phone but that doesnt work either since the silver buttons are unresponsive.
So now I'm looking for the Clear_Storage thing I've been reading about but I can't find it so could someone please supply me with the directory I could find it in or any other solution you can think of to help me hard reset my phone so I can flash a new ROM.
BTW I've used Hard-SPL to flash roms before, it's just this last ROM from itje got all screwy and made the buttons stop working.
Thanks, Nik
Setting > System > Clear Storage.
Sometimes Itje takes it out of his ROMs, though. You can try reflashing by pc method if it's not there.
Yea I've checked and it's not in there, how would you do it by pc?
Is it that ruu executable that you run while it's synced? For some reason
that never actually worked with my comp which is why I always resorted to the SD Card Flash method, but I can't get into the Hard-SPL loader now cause of the button problem.
Does anyone know how to hard-reset without having to use the hardware buttons, because I really need to be able to use my phone again.
Need Help =/
Next to malfunctioning buttons, is the phone starting up?
What happens, if you plug a USB cable in? If you can select ActiveSync mode, then you could easily try to re-flash another ROM image - maybe the one you have been using was corruptly downloaded or something.
Or, if you get too much of strange behaviour like this, try a stock ROM first, then another custom ROM.
It boots up and works fine as long as I stick to using the touch screen and I can USB ActiveSync it too. I know some of the older ROMs used to have an exe you could run while in ActiveSync and it would auto install but most of the new ROMs assume you're using the SD Card Method so I can't find the PC Installer app.
Alright so I managed to isntall a new version of that Firestorm Rom (3.8 I think) and my hardware buttons still don't work.
Like from the buttons that Works:
Power Button
Camera Button
Optical Joypad (only the center square)
Stuff that doesn't work:
X-Panel Button
Ok Button
Volume Button (up, down, center)
Pick up Call
Hang Up Call
Two Silver Buttons (left and right)
Left and Ride on "D-Pad"
ALL KEYBOARD KEYS
What is their left to do if a new ROM doesn't fix the problem?
what are my options for getting this fixed?
my volume keys dont work, dont know why but sometimes theyre working and sometimes not.
i have the same issue. but my g-letter button works. and all other buttons make the volume go up one notch and then down again. further more when i go into settings and the menu that controls what the buttons it only says it has a left and a right button.
have u been able to figure something out??
began working again
after a month it suddenly started to work again! dont know why or how
is a hardware problem, with your flex.
i can tell you this is hardware problem.flash your phone with orginal spl and orginal rom and send sony ericson.i had same problem.they gave me new unit after 3 months fight good luck.
no doubt, it's hardware problem..
Agree with human75, flash your x1 with stockSPL n original ROM before u send it to SE. Do it via your PC.. Goodluck bro
I can't get any of my emulators to work with my wii mote. All have been working all perfectly on my g tablet. When I try to map the keys by pressing the button it doesnt detect it... it just says press hardware key. any ideas??
anyone? Im thinking maybe I need my nunchuk pplugged in? Thats all I can think of at this point. I had it worked on my gtab and the menu was different.... the box is smaller where it says to press the button I want to use, there was a place for it to display the button i pressed, now theres just the OK box..
really odd
Update...
the programs say "Press hardware key to map"...
If I press a HARDWARE KEY, like volume up, it takes it. But it wont read the wiimote at all. I guess my issue is getting it recognized, even though the program I have has synced with it
Figured it out, the 4th wiimote app from the market finally worked. Use "simple wiimote" - works great! Cant wait to hook this up to my 55" LED !
DroidHam said:
Update...
the programs say "Press hardware key to map"...
If I press a HARDWARE KEY, like volume up, it takes it. But it wont read the wiimote at all. I guess my issue is getting it recognized, even though the program I have has synced with it
Click to expand...
Click to collapse
You are doing the process correctly. However you gotta goto the settings of the emulator and under input there is a check box that says "other input" check that and then it will work
Hi
The shIFt key seems to turn on and off automatically for some reason. started yesterday. I tried a lot of things to see if the problem goes away but it hasn't. I'll list what I've done so YOU guys know.
restarted, turned the accessibility action off (where you click shift 5 times) still nothing. I opened up tHe ON Screen kEYboArd and saw the two shift keys kept on flicking. Tried the alt + ctrl thing. Didn't work.
I know it's not to do with the keyboard as i plugged it out and the on screen keyboard still kept on toggling On aNd OFf
I'm Running
OS: Windows 7 64bit
Driver: NVIDIA GeForce GTS 450