Screen problems - Touch Diamond, MDA Compact IV General

I am using the ROM [ROM][29JAN10]Gen.Y D2X R2.1[WM6.1 21056][UC][SENSE2.5][WWE|GER|NLD|ITA|FRA|SPA] with Radio version:1.13.25.24
I have to mention that the problem begin using the ROM [ROM][22JAN10]Gen.Y D2 R5.3[WM6.1 21056][UC][SENSE2.1][WWE|GER|NLD|ITA|FRA|SPA].
I made a hard reset on my HTC Touch Diamond because the GPS was not working. After that I began to experience strange things with my device, the screen was starting blinking if I was pressing the action button or any button from the device - if I make a soft reset the device says ''HTC Touch Diamond'' ok, after that is the welcome screen of the ROM, but after that the screen of the device goes off and I need to press the power button several times to see anything on the screen. After that if I am trying to access anything using the buttons from the device, the image on the screen starts to blinking and only if I press the power button to turn off the screen and after that to press again the power button to turn on the screen, the screen comes to normal. Until making the hard reset I never had this kind of problems. What is happening with my device?

These look like software problems. Have you tried flashing a non-Gen.Y ROM?
~codeslicer

I would try that if I even could connect the device to my computer and be recognize. I don't know what happened either with the computer or either with the device because the device is not recognize by the computer.

Related

Startup Blocked following new ROM!

Hi
It's not the first time I flash my TytnII, but this time, I get worry about my phone...
I've tried to put the kaiser_wwe_shifu_v3.0 rom's.
According to doc, I've upgraded Radio and Hard SPL.
Radio is 1.70.19.09
Hard SPL is 3.29.
The upgrade of ROM was OK, but some stranges things appened therefore. The first boot, OK the device is configuring itself, and rebooting.
After the first reboot, the device is still "fresh installed"! So here we go another time to pre-configure it...(time, touch screen...)
After, it seems to be OK, but in fact, I see there's no more memory to completely startup the phone. Because the phone starts, but finally, a program (don't remember which one) says that it cannot start because lack of memory...)
I reboot, and since, me phone doesn't boot at all....
It display the startup page with radio , hard SPL infos, but no more, it seems to be completly block on these steps.
What could I do?
Thanks a lot
Have you tried to flash another ROM?
You can try this bij holding camera button while booting, you should see the tri-color screen. Connect it to your PC and try to flash again or another (maybe stock-rom?) ROM.
Good luck
No funny multi color screeen appears when pressing camera button while booting...
Can't connect a cd reader on it, and erase flash
thanks
Do a hard reset and see if that works, hard reset is hold down left and right softkeys and and hold in reset button with stylus until you get to a screen about resetting the phone, remember to back up any data on phone memory cos you will lose this after a hard reset
I want to second this problem.
After flashing the Radio to "KAIS_RADIO_ONLY_1.71.09.01" and installing PDA corners newest ROM, everything worked fine. The only bug was that when I wanted to turn off the device by holding the power button, after choosing the turn-off option, it just restarted.
Now the phone doesn't start at all. Seems as if there is no power from the battery, while there was enough charge in it. When I connect it to the power plug, the charging/power led turns almost red, never saw that before.
This is not my first ROM-update, but this is the first time I've encountered this problem.
I tried hard and soft resets, removed the battery, tried to connect it to the pc, nothing worked.
Any ideas?
Thanks.
Press and hold the camera and the power/ on buttons. While ho[ding both buttons, do a soft reset. Once in bootloader ( tri color ) flash your original stock rom.
What I already tried:
- hard and soft resets
- removed the battery
- tried to connect it to the pc
- connected in the power plug, nothing worked.
- tried the power button+camera+soft reset
I download the the same Rom....I I have the same problem.... I Reset with Pressing Camera and Power method....it went to the Hardspl screen and I load a new ROM...its working fine now.

Buttons quit working / not responding

This is the second Sprint Touch Diamond I've had with this problem, and I'm wondering if anyone else is experiencing it. I boot the phone fresh, then when it's done turn off the display with the power button. When I press the power button again, it turns on, and then the buttons stop working. The device is fully usable other than no buttons, including power, work. The display also stays on, and will not turn off after the normal period of time. I also noticed if I hold the power button, the pop-up for a soft reset will come up, but choosing yes does not actually soft reset it.
Has anyone else had this problem and fixed it without bringing it in?
Thanks!

Diamond not going to boot loader

Hi,
Diamond is not going to bootloader (tricolour) screen after MTTY. MTTY was successful but nothing happening after pressing volumedown+center button.
Now device is just showing - Touch diamond when i switch on.
I have diamimg.nbu on internal storage, is there any way to trigger install.
It was working fine before mtty.
Pull battery out to turn it off.
Put it back in.
Press and hold volume down
Press reset button.
The reason its only showing Touch Diamond is that the MTTY process has cleared off your previous OS. You need to get it back to bootloader and try MTTY again.
I have tried all those stuff but no luck, for every thing diamond just vibrates and shows "Touch Diamond".
I guess boot loader is not working, is there any way to connect to it and repair bootloader.
I have tried snoopy from some post but thats also of now help.
Taken from PPCGeeks:
"Hold down the Volume down key and power button, the take the tip of your stylus and press the soft reset button (bottom left corner of phone under battery cover). After you press reset button keep the Volume down and power button press until the bootloader screen comes up"
Let us know if this works.
Thanks Super....
This is not working, only option i see is some way to connect to it through USB because i had faced this problem earlier also but that time RRU updater used to push it to bootloader.
volume down button used to work only with original HTC ROM for me....only a few time it used to work with cooked ROMs....
Hi,
Anyone can suggest some advance tool which can connect to diamond if its not going to bootloader through normal methods.
Its all clear by MTTY, i have ROM image on internal storage.
Solved finally.......
Hold only volume button pressed, press reset button and immediately after that press ok or back button

[Q] My kaiser has died, What Can I DO?

hi,
I have a big problem, I don't know what can i do, and I deseperate, I was flashing my device using a SD Card, then the process stopped the progress bar was stopped, I waited for a while, but nothing happened, then I turned off my device but now It doesn't work, It doesn't turn on, and when I plugged the charger the indicator led doesn't turn on, I don't know if my device will not work anymore, please If you can help me I will be thankful, thanks!!!!.
press red button and green button with hardest key set will reset automatically
hi thanks for answer, I was trying to do that you said me but nothing happens I don't know if I'm doing something wrong, press the red button and the green at the same time, and Should I press the soft reset key??? Sorry but I don't know what is the other key that you said, however I pressed green and red button and the Reset key and nothing happened, also I tried with the soft keys and the reset and nothing!!!!!
To perform a hard reset using device keys
1. Press and hold the left SOFT KEY and the right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device.
2. Release the stylus, but continue pressing the two SOFT KEYs until you see the following message on the screen:
3. Release the two SOFT KEYs, and then press green button (phone icon)the HTC Kaiser TyTN II P4550 Hard reset Soft reset Hardreset Softreset button on your device.
Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
To perform a hard reset using Clear Storage
1. Tap Start > Settings > System tab > Clear Storage.
2. Type “1234” in the box and tap YES.
Back to main site
after that you can Flash again with official ROM for your device
hi thanks for answer, I've already done this many times but It doesn't work, It is still dead, the led charge indicator doesn't turn on, It doesn't turn on, nothing happens It just is dead.
If you remove the battery, and boot the phone, will the LED turns green?
If it does, I have the same problem, then..
hi, the indicator LED never turns green, they neither turn on.
myANdrew16 said:
hi, the indicator LED never turns green, they neither turn on.
Click to expand...
Click to collapse
you try with another battery (battery type)...!
because the device is hard brick with the physical characteristics of a black screen (no boot loader) and only the green LED on
Same thing happened to my Kaiser last winter. I even tried a new display. Bit nothing. Then I let it rest for one or two weeks and it worked just fine again.. Maybe it was the cold.
Hakim Rahman said:
you try with another battery (battery type)...!
because the device is hard brick with the physical characteristics of a black screen (no boot loader) and only the green LED on
Click to expand...
Click to collapse
hi, thanks for answer
definitely I think that it's without boot loader, but in this moment I don't have another batt, but I don't understand why the LED indicator doesn't turns green when I plug the charger without batt installed, Do you believe that it can be saved?
one more thing, that I was flashing my device, maybe everything inside it was erased,
I don't know it's just a supposition
My advice should you take your device to customers service to be examined or to repair
I hope your device can be saved ..

Phone touch screen not working and phone won't turn off

Hi everybody,
So I have an HTC One M7 running Google Play Edition Rom and my touch screen stopped working. Now, this isn't the first time it has happened but it is the first time it's happened on this rom. I was previously running Android Revolution HD and when my touch screen stopped working, I would hard reset by pressing and holding the power and volume down button until the buttons started blinking for around 10 seconds, and then the phone would restart. However, I can't hard reset my phone anymore. I tried holding the power and volume down button down, but after a full minute, the phone still didn't restart; it was just the capacitive buttons flashing. I tried every combination of holding down buttons but it still doesn't work. What should I do? Any help would be appreciated.
use an OTG cable adapter and plug a mouse ;
go to settings backup and reset : reset phone .
if this is what you want to do.
kinda only way to reboot if you stuck .
or download a rebooter apk

Categories

Resources