[Q] My kaiser has died, What Can I DO? - Tilt, TyTN II, MDA Vario III General

hi,
I have a big problem, I don't know what can i do, and I deseperate, I was flashing my device using a SD Card, then the process stopped the progress bar was stopped, I waited for a while, but nothing happened, then I turned off my device but now It doesn't work, It doesn't turn on, and when I plugged the charger the indicator led doesn't turn on, I don't know if my device will not work anymore, please If you can help me I will be thankful, thanks!!!!.

press red button and green button with hardest key set will reset automatically

hi thanks for answer, I was trying to do that you said me but nothing happens I don't know if I'm doing something wrong, press the red button and the green at the same time, and Should I press the soft reset key??? Sorry but I don't know what is the other key that you said, however I pressed green and red button and the Reset key and nothing happened, also I tried with the soft keys and the reset and nothing!!!!!

To perform a hard reset using device keys
1. Press and hold the left SOFT KEY and the right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device.
2. Release the stylus, but continue pressing the two SOFT KEYs until you see the following message on the screen:
3. Release the two SOFT KEYs, and then press green button (phone icon)the HTC Kaiser TyTN II P4550 Hard reset Soft reset Hardreset Softreset button on your device.
Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
To perform a hard reset using Clear Storage
1. Tap Start > Settings > System tab > Clear Storage.
2. Type “1234” in the box and tap YES.
Back to main site
after that you can Flash again with official ROM for your device

hi thanks for answer, I've already done this many times but It doesn't work, It is still dead, the led charge indicator doesn't turn on, It doesn't turn on, nothing happens It just is dead.

If you remove the battery, and boot the phone, will the LED turns green?
If it does, I have the same problem, then..

hi, the indicator LED never turns green, they neither turn on.

myANdrew16 said:
hi, the indicator LED never turns green, they neither turn on.
Click to expand...
Click to collapse
you try with another battery (battery type)...!
because the device is hard brick with the physical characteristics of a black screen (no boot loader) and only the green LED on

Same thing happened to my Kaiser last winter. I even tried a new display. Bit nothing. Then I let it rest for one or two weeks and it worked just fine again.. Maybe it was the cold.

Hakim Rahman said:
you try with another battery (battery type)...!
because the device is hard brick with the physical characteristics of a black screen (no boot loader) and only the green LED on
Click to expand...
Click to collapse
hi, thanks for answer
definitely I think that it's without boot loader, but in this moment I don't have another batt, but I don't understand why the LED indicator doesn't turns green when I plug the charger without batt installed, Do you believe that it can be saved?
one more thing, that I was flashing my device, maybe everything inside it was erased,
I don't know it's just a supposition

My advice should you take your device to customers service to be examined or to repair
I hope your device can be saved ..

Related

Help: Kaiser stuck in some weird RGBW screen... won't boot

Sorry if this has been asked and answered before... a quick search turned up nothing useful - but then I only got this device about a week ago and don't really know what to look for.
I pressed the Soft Reset button with the USB cable attached and the phone seems to have gone into some weird mode and now nothing I do will make it boot.
I'm stuck on a screen with 4 sections, Red, Green, Blue, and White.
The text
KAIS130
SSPL-1.93.0000
CPLD-8
is displayed on the red section, and the letters USB on the white.
I have tried soft reset (always comes back to same screen), hard rest (does nothing), taking the battery out and putting it back. All with and without the cable attached.
Is there anything I can to do restore my device or do I need to return it?
Many thanks for any help.
You may in Bootloader mode. You may have to force a hard reset. I think if you hold the camera button and power button while turning on it should bring it up, but I am not sure on the Kaiser. I am sure someone will post up the exact procedure. I hope everything turns out OK for you.
Kevin
Thanks for the reply... I got the impression that might be the case from a google hit as well. Grrr. I was just trying to cure a 'not syncing' issue.
Alas I can't find anything to make a Hard Reset do anything - I've tried every combo of buttons I can think of, including the one in the manual and the one you just suggested... no dice
Oh well, I guess I have a very expensive paper weight
Press and hold the two action buttons (the - in between red and green buttons) and press reset with the stylus.
keep them pressed for a bit, then release only the reset button
press and hold the two soft key buttons and press reset with the stylus.
keep them pressed for a bit, then release only the reset button
after releasing the reset button hit send ( the green key ) it should show on the screen if you have done it correctly to push the send button to complete the hard reset, if not repeat the process again
if that doesnt work you can always reflash the rom using the original Kaiser rom RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88. 07_1.27.12.11_Ship.exe
its here http://forum.xda-developers.com/showthread.php?t=331900&highlight=official+kaiser+rom
since its already in the bootloader mode it will be able to be flashed if it wont hard reset
Hmm, nope the Soft+Soft+Reset doesn't do anything other than the normal reset
I think before I try the ROM flash I'd better contact HTC and make sure I'm not voiding my warranty.
It's a shame I'm going to loose the days work
thanks for the help folks.

Helpme Please My HTC Kais130 (AT&T Tilt) NO RUN , IS DEAD

Helpme Please My HTC Kais130 (AT&T Tilt) NO RUN , IS DEAD, only power on and ( smart mobility in display black) and no more
helpme please
Hello there, we all understand youre frustration. But for beeing able to assist you everyone need to know what exactly happend here? Where you flashing? Did it fell out of youre pocket? What where you doing last on it and so on. Take 5 minutts or more and provide as much info you can then edit youre post. That is AFTER you have searched and digged trought this board using google aswell for keywords on youre issue.
didnt flash, it was working well suddenly is dead, plug in cable usb,and is the same but on screen appear "smart mobility" vibe and then off
hanster said:
didnt flash, it was working well suddenly is dead, plug in cable usb,and is the same but on screen appear "smart mobility" vibe and then off
Click to expand...
Click to collapse
did u try hard reset?
No , i didnt do it, i dont kwon how to do it?
hanster said:
didnt flash, it was working well suddenly is dead, plug in cable usb,and is the same but on screen appear "smart mobility" vibe and then off
Click to expand...
Click to collapse
I know this is a abiouse question but I have to ask, mate.. You are not running flat on batteries? If you havent flashed youre device, and it wount boot and you got power on it you should check youre waranty on the device. Try to charge it for 10 minuts or so (check that you have charging light on) then try to start it again.
I understand you correctly that you havent HardSPL youre device at all or?
hanster said:
No , i didnt do it, i dont kwon how to do it?
Click to expand...
Click to collapse
u should do a hard reset.
Here is a step by step for u:
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets
Remember after performing a hardreset, u will loose all your data on your phome(not on SDcard).
Kaiser_Resets
Back to Kaiser Wiki
--------------------------------------------------------------------------------
Soft Reset
Using a stylus, press the soft reset button at the bottom of the phone
Hard Reset **NB** This cannot be performed while the device is connected/charging!**
Press and hold both soft keys
Using a stylus, press and hold the soft reset button at the bottom of the phone
Keep all three buttons pressed until the keypad lights turn off and then flash
Release the soft reset button while still pressing the soft keys
Let go of the two soft keys once the message "This operation will delete all your personal data, to manufacturer default" appears on screen
Finally, press the green call button to perform the hard reset, or press other key to cancel
Bootloader
Press and hold the Camera button
Using a stylus, press and hold the soft reset button at the bottom of the phone
Release both buttons once the bootloader screen appears
did u do it?
this is my phone
this is my phone where is it the soft key
Press and hold both soft keys
I have currently disabled pics so I cant see the pics of your phone.DOnt u have kaiser?
The soft buttons are the ones next to gren and red phone buttons and above messaging and internet buttons.
im doiin that but dont do anything, dont show a message for reset phone what more can i do, can i repair with any software, any test mode , any flash
hanster said:
im doiin that but dont do anything, dont show a message for reset phone what more can i do, can i repair with any software, any test mode , any flash
Click to expand...
Click to collapse
just be sure u are doing the hardreset right. Some guys had problems, cause they had big fonger and they were pushing not just the soft buttons but also a buttons that are around them.
Hold these two soft buttons, then stick the stylus to the hole and hold it there antil a white screen appears where is the message shown. Then push the green phine button.
http://www.mediafire.com/?rc3vbcqdtbh
here you go a video
http://www.mediafire.com/?lrgmtzy4mat
here you go a video of problem the my HTC
hanster said:
http://www.mediafire.com/?lrgmtzy4mat
here you go a video of problem the my HTC
Click to expand...
Click to collapse
Ok, I have seen the videos. Did u try the reset with the kaiser closed?
I remember a thread with similar problem, will try o find it and post back.
PS: In the first video, u have three hands!!
OK, I found this one:
http://forum.xda-developers.com/showthread.php?t=374388&page=3
Similar problem, does your kaiser reboot continuosly or the screen just flashes.
Your best bet is to read the whole thread, try to learn something about mtty and contact gsleon.

Upon soft reset phone does not boot

I tried to make a call a few minutes ago and I couldn't hear any sound but screen said call was connected. I did a soft reset and now I'm getting this message "KAIS1*0 mfg. SPL-1.0.01pof CPLD-8" on the tri colored screen. I've been using my installed rom for over a year and a half now.
I'm in a situation now where I don't have time to research this issue so I'm sorry if this situation has been posted in the past. I apologize... Just wondering off hand if this or a similar issue has happened to anyone else in the past. If I have any options besides reflash. I'm on call for work and I'm going to have to pick up a new phone until I can do some research.
Many Thanks!
UPDATE: My phone will boot when plugged into the charger, if I unplug the phone and try to boot it will not. One other thing I noticed is that my speaker doesn't work now when unplugged, but does when I'm plugged in. Not sure where to go from here could it be my mini usb connector on the phone that's causing this?
dewicide said:
I tried to make a call a few minutes ago and I couldn't hear any sound but screen said call was connected. I did a soft reset and now I'm getting this message "KAIS1*0 mfg. SPL-1.0.01pof CPLD-8" on the tri colored screen. I've been using my installed rom for over a year and a half now.
I'm in a situation now where I don't have time to research this issue so I'm sorry if this situation has been posted in the past. I apologize... Just wondering off hand if this or a similar issue has happened to anyone else in the past. If I have any options besides reflash. I'm on call for work and I'm going to have to pick up a new phone until I can do some research.
Many Thanks!
Click to expand...
Click to collapse
Try a hard reset.
Hard Reset
- Press and hold both soft keys (The two inside the green and red phone ones)
- While holding softkeys, using a stylus, press and HOLD the soft reset button at the bottom of the phone
- Keep all three pressed until the keypad lights turn off and then flash
- Release the soft reset button while still pressing the soft keys
- Let go of the two soft keys once the message "This operation will delete all your personal data, to manufacturer default" appears on screen
- Finally, press the green call button to perform the hard reset, or press other key to cancel
this could be a battery issue and if it is you need to clean the contacts or get a new battery
I thought the same thing so I swapped batteries with my girlfriend who also has the same phone. My battery works in her phone and with hers in mine I still have the same issue. My battery compartment was very clean. I pried up my contacts a bit though. After opening my girlfriends phone up, hers is a different story. I stumbled upon this thread about stuck spl staying in bootloader mode. I wonder if this could be my issue? http://forum.xda-developers.com/showthread.php?t=420683
Everything seems to match up with the issues I'm having...

Screen problems

I am using the ROM [ROM][29JAN10]Gen.Y D2X R2.1[WM6.1 21056][UC][SENSE2.5][WWE|GER|NLD|ITA|FRA|SPA] with Radio version:1.13.25.24
I have to mention that the problem begin using the ROM [ROM][22JAN10]Gen.Y D2 R5.3[WM6.1 21056][UC][SENSE2.1][WWE|GER|NLD|ITA|FRA|SPA].
I made a hard reset on my HTC Touch Diamond because the GPS was not working. After that I began to experience strange things with my device, the screen was starting blinking if I was pressing the action button or any button from the device - if I make a soft reset the device says ''HTC Touch Diamond'' ok, after that is the welcome screen of the ROM, but after that the screen of the device goes off and I need to press the power button several times to see anything on the screen. After that if I am trying to access anything using the buttons from the device, the image on the screen starts to blinking and only if I press the power button to turn off the screen and after that to press again the power button to turn on the screen, the screen comes to normal. Until making the hard reset I never had this kind of problems. What is happening with my device?
These look like software problems. Have you tried flashing a non-Gen.Y ROM?
~codeslicer
I would try that if I even could connect the device to my computer and be recognize. I don't know what happened either with the computer or either with the device because the device is not recognize by the computer.

i bricked my x1

i tried to upgrade the rom from WM6.1 to dynamics 2.0
i did everything and update successfully.
x1 reboot and went into start up screen saying hard reset on first run,
i tried to hard reset but my "R" dont seems to be working..
so i pressed "space bar" to restart.
after that it cant start up, i tried to hard reset, soft reset, take out battery, nothing seem to work, only a pulse of vibratiion... the screeen remains totally blank.
is my x1 dead?
thanks for the help
B3nGz said:
i tried to upgrade the rom from WM6.1 to dynamics 2.0
i did everything and update successfully.
x1 reboot and went into start up screen saying hard reset on first run,
i tried to hard reset but my "R" dont seems to be working..
so i pressed "space bar" to restart.
after that it cant start up, i tried to hard reset, soft reset, take out battery, nothing seem to work, only a pulse of vibratiion... the screeen remains totally blank.
is my x1 dead?
thanks for the help
Click to expand...
Click to collapse
try to flash that rom again
try to hold two silver keys and push the power button till you see tricoloured screen or try pushing two silver keys and soft reset button with stylus which is located in a tiny hole just stylus sized on the back right side of the phone
i tried 2 silver buttone with the power button and the back hole.
but my screen still remain blanked.
totally nothing.. only a pulse of vibration.
is it possible to be in this stage? will a totally bricked x1 still able to get tri color?
i think u should charge your battery. and then put a kovsimg.nbh file on sd card.
after that install the rom by pressing the volume button down and power button.
px1ilanmy said:
i think u should charge your battery. and then put a kovsimg.nbh file on sd card.
after that install the rom by pressing the volume button down and power button.
Click to expand...
Click to collapse
hi,
i have tried charging the phone,
i tried pressing 2 silver buttons and power button
i tried pressing 2 silver button and stylus poke reset hole for 5 sec
i tried power button with volume down..
nothing works.. its just give a pulse of vibration and a black lighted up screen, nothing else.
anyone please help. =(
you know those leds on the sides of the phone try charging the phone and see if they glow if they do then your screen may be broken or your flex cable has worn off i'll put my money on the flex cable if so then you should order a new one and replace it or take it to a service centre
Info about the way you've got to the trouble looks little... not clear.
i tried to hard reset but my "R" dont seems to be working..
so i pressed "space bar" to restart.
Click to expand...
Click to collapse
How did you press space bar if "R" doesn't work?
Then... If you can get into bootloader mode, you can reflash any rom you like... you have hard-spl installed, have you?
You can use few different combinations to get into bootloader -"power"+"vol-down" OR "power"+"cam button". As you have vibration on the start, I assume your bootloader isn't broken, so you should be able to do these operations.
Charging should work as well, even if you don't see any sign of charging.
bruno_123 said:
you know those leds on the sides of the phone try charging the phone and see if they glow if they do then your screen may be broken or your flex cable has worn off i'll put my money on the flex cable if so then you should order a new one and replace it or take it to a service centre
Click to expand...
Click to collapse
Yeah i can charge,
Led at the side does glow, when i call it will blink and vibrate, but i cant pick up, no buttons is working on the front screen, dont know about th qwerty..
i guess flex is crappy.. but if flex is crappy, the screen will light up but remain blank? the led will glow?
ultrashot said:
Info about the way you've got to the trouble looks little... not clear.
How did you press space bar if "R" doesn't work?
Then... If you can get into bootloader mode, you can reflash any rom you like... you have hard-spl installed, have you?
You can use few different combinations to get into bootloader -"power"+"vol-down" OR "power"+"cam button". As you have vibration on the start, I assume your bootloader isn't broken, so you should be able to do these operations.
Charging should work as well, even if you don't see any sign of charging.
Click to expand...
Click to collapse
thanks for the advise. i will try again! and report in again..
thanks alot bro!
B3nGz said:
i guess flex is crappy.. but if flex is crappy, the screen will light up but remain blank? the led will glow?
Click to expand...
Click to collapse
if you don't see SE logo on the start and backlight is turned on, if you don't see bootloader tricolor... looks really like it is flex (double check - I am not so advanced in hardware repairing).
Yes, leds should glow in that case.
ultrashot said:
Info about the way you've got to the trouble looks little... not clear.
How did you press space bar if "R" doesn't work?
Then... If you can get into bootloader mode, you can reflash any rom you like... you have hard-spl installed, have you?
You can use few different combinations to get into bootloader -"power"+"vol-down" OR "power"+"cam button". As you have vibration on the start, I assume your bootloader isn't broken, so you should be able to do these operations.
Charging should work as well, even if you don't see any sign of charging.
Click to expand...
Click to collapse
Hi the x1 is able to start up already.
surprisingly, for its blank screen, im able to connect and sync on windows centre and load up hardspl.
after that i follow ur instruction on power+camera, it started showing tricolor and rom flash.
thanks for all the help guys.
THANKS!
my bad , sorry for wrong info

Categories

Resources