Hi all,
plz ,i have a big problem in my spv-m3000 G4
i flashed it with wm6 tnt 4
and it work normally ,after that i flash it with other wm6 rom and it stop flash in 99% ,then i reflash with other original rom and complete flash normally in boot after splash screen ,i dont know how i press reset then the device won't start
now only in charg if i remove the battery the red led on for one second
plz help me because in my country there is no repairing service for this model
Can You access Bootloader? Tri colored Screen with IPL and SPL info
Some Wizards have an operator Flash screen which overrides the Flash screen that's supposed to show the IPL and SPL versions. In this case, you can try to enter the bootloader (by resetting the device (by pushing the stylus into the reset button at the right of the device) and then holding the camera button). This is from the Wiki for the Wizard
Tweakecho said:
Can You access Bootloader? Tri colored Screen with IPL and SPL info
Some Wizards have an operator Flash screen which overrides the Flash screen that's supposed to show the IPL and SPL versions. In this case, you can try to enter the bootloader (by resetting the device (by pushing the stylus into the reset button at the right of the device) and then holding the camera button). This is from the Wiki for the Wizard
Click to expand...
Click to collapse
thanks for reply
but the device don't start u have another idea like j tag or ??????????
any one help me plz
I've upacked my shiny new XDA Ignito and followed the intructions to install HardSPL.
The TUT says:
<snip>
To verify if you indeed have correct HardSPL on your device, enter Bootloader by pushing the reset button while holding volume down key on the side.
It should display*:
* In case of another HardSPL, the version number would differ!
Code:
…
SPL-1.40.OliNex
</snip>
I don't see this - I just boot into the O2 welcome screen - the update took about 2 minutes - has it failed or is there anyway to confirm the HardSPL has taken? I don't want to install a new ROm until I'm sure I'm not going to brick it....
TIA
Peter
put your phone into bootloader mode and you will see that your SPL has changed to OliNex 1.40.
This information will not show on the normal splash screens.
to put your phone into bootloader you need to turn the power off on your phone, once the device is off, press and hold the volume down then press and hold the power button.
hope this helps
My phone: T-Mobile MDA Compact IV
I started the HARDSPL upgrade by the upgrade tutorial.
It flash the unsigned 1.40 succesfully and i clicked finish on the application.
My phone was restarted.
Now i want to verify that the OliNex HARDSPL is installed by pressing the reset button while holding the volume down bottun.
Nothing will happen.
My sound will go off and the screen goes black. I tried everything i can think of.
How to enter the bootloader?
Or do i have to flash it to the Unsigned HARDSPL 1.40 again?
Greetings,
Angkasa
While holding the volume down press the reset button and don't let it go till you see the coloured screen.
I think you let it go too soon.
i am trying to use SEUS to update my rom, the problem is i cant enter the bootloader
i followed these instructions.
1. make sure battery power is 50% above
2. turn off x1
3. remove battery
4. return battery
5. hold volume down, then hold power
after that, my x1 boots normally, not in bootloader.
help please
dlegendkiller said:
i am trying to use SEUS to update my rom, the problem is i cant enter the bootloader
i followed these instructions.
1. make sure battery power is 50% above
2. turn off x1
3. remove battery
4. return battery
5. hold volume down, then hold power
after that, my x1 boots normally, not in bootloader.
help please
Click to expand...
Click to collapse
2. Make sure X1 is off
3.-4. You can skip this if X1 is really off
5. Press on the "down volume" (the button you press to decrease volume level) and DO NOT LET GO
6. WHILE STILL PRESSING the volume down key, press the power button AND DO NOT LET GO OF BOTH KEYS until the tricolor screen appears
it still doesnt work sir,
pinoy here
are there requirements in entering bootloader?
please help me, is it required to have my memory card formatted? and my phone is fresh (hard reset)?
If you just want to update your phone, you really don't need to use SEUS. Just flash the WWE R3A stock ROM (it's in the stickied thread in the ROMs section) using the RUU (activesync) method
harveydent said:
If you just want to update your phone, you really don't need to use SEUS. Just flash the WWE R3A stock ROM (it's in the stickied thread in the ROMs section) using the RUU (activesync) method
Click to expand...
Click to collapse
but in this case it think it's very important to say that it's only that simple if he want's to flash a stock-rom!!!
(meaning "an original rom by SE")
@dlegendkiller:
if you ever want to flash a custom-rom then first read about flashing hard-spl and then do it before flashing custom-roms. if not, you can get into serious trouble. (it's easy and save if you follow the instructions)
dlegendkiller said:
please help me, is it required to have my memory card formatted? and my phone is fresh (hard reset)?
Click to expand...
Click to collapse
honestly, i think you're either doing something wrong here OR your volume-button is broken. regardless of your sd-card you should be able to enter bootloader-mode (the tri-color screen).
are you really doing it this way? to test do it without the usb-cable attached:
- turn your phone off completely
- press your volume-down-button and keep pressing it
- now press the power-button and also keep pressing it
you'll know when to release the buttons yourself.
anyway, can i get some advantages in updating my rom? i really am scared to install custom roms, i might break the phone
and i want to install manila hd, i am wondering why i cant install it
its about "system permissions etc etc"
does it require custom rom?
i have installed Olipro HardSPL 1.20 then i have installed wm 6.5 rom
and now the mobile could not boot
it goes to the splash screen and it stay at thes screen
what shall i do ?
can i remove (Olipro HardSPL 1.20)?
help me plz
Can it enter bootloader mode? Press and hold Power + Camera then press reset button. If it enters the multicolor screen and says Olipro 1.20 then try to install some other ROM. It may be that your ROM copy is corrupt.