i have installed Olipro HardSPL 1.20 then i have installed wm 6.5 rom
and now the mobile could not boot
it goes to the splash screen and it stay at thes screen
what shall i do ?
can i remove (Olipro HardSPL 1.20)?
help me plz
Can it enter bootloader mode? Press and hold Power + Camera then press reset button. If it enters the multicolor screen and says Olipro 1.20 then try to install some other ROM. It may be that your ROM copy is corrupt.
Related
I have flashed this rom to my fone ok.
it started up, synced with a/s 4.5, evrything was ok.
i did a soft reset and now i cant get past the green windows mobile screen.
the green light is flashing and the start/end call buttons light up.
it wont turn off on the main power button, will only soft reset.
any ideas??
kieron
...it also lights up if you ring it.
it doesn't just go straight to answerfone as it would if it was swiched off or out of signal, so it must be connecting to the network....
Go to Bootloader (Hold Camera-Button + Reset) and flash ur operator Rom back!!!
sorted!!!
cheers dude
damn poxy fone
will not go to bootloader
any other ideas please?
ipl 1.01
spl 1.01
shows loading windows screen and that all...
os 3.3.0.0
most of the aku 3.3 roms require that you load a 2.* ipl spl rom first, then load the aku 3.3 rom.
Hi all,
plz ,i have a big problem in my spv-m3000 G4
i flashed it with wm6 tnt 4
and it work normally ,after that i flash it with other wm6 rom and it stop flash in 99% ,then i reflash with other original rom and complete flash normally in boot after splash screen ,i dont know how i press reset then the device won't start
now only in charg if i remove the battery the red led on for one second
plz help me because in my country there is no repairing service for this model
Can You access Bootloader? Tri colored Screen with IPL and SPL info
Some Wizards have an operator Flash screen which overrides the Flash screen that's supposed to show the IPL and SPL versions. In this case, you can try to enter the bootloader (by resetting the device (by pushing the stylus into the reset button at the right of the device) and then holding the camera button). This is from the Wiki for the Wizard
Tweakecho said:
Can You access Bootloader? Tri colored Screen with IPL and SPL info
Some Wizards have an operator Flash screen which overrides the Flash screen that's supposed to show the IPL and SPL versions. In this case, you can try to enter the bootloader (by resetting the device (by pushing the stylus into the reset button at the right of the device) and then holding the camera button). This is from the Wiki for the Wizard
Click to expand...
Click to collapse
thanks for reply
but the device don't start u have another idea like j tag or ??????????
any one help me plz
I've upacked my shiny new XDA Ignito and followed the intructions to install HardSPL.
The TUT says:
<snip>
To verify if you indeed have correct HardSPL on your device, enter Bootloader by pushing the reset button while holding volume down key on the side.
It should display*:
* In case of another HardSPL, the version number would differ!
Code:
…
SPL-1.40.OliNex
</snip>
I don't see this - I just boot into the O2 welcome screen - the update took about 2 minutes - has it failed or is there anyway to confirm the HardSPL has taken? I don't want to install a new ROm until I'm sure I'm not going to brick it....
TIA
Peter
put your phone into bootloader mode and you will see that your SPL has changed to OliNex 1.40.
This information will not show on the normal splash screens.
to put your phone into bootloader you need to turn the power off on your phone, once the device is off, press and hold the volume down then press and hold the power button.
hope this helps
Hi
my Charmer freezes during the Bootprocedure (IPL SPL GSM OS is showing)
I tried to upgrade to Charmer WM 6.1 by ChrBeck but when the os file is written the connection cuts :-(
what should I do ??
Anywhen I used a safe mode but i don't know how to get there.
Does someone know how ???
Thanks for help
OK i figured i out just press the Camera Button after you pressed the reset button
I'm sorry to bother you but i really fu**ed my blackstone. My problem is that i got SPL 1.54, so i can't flash anymore roms, furthermore i got black dragon 3.3 which unfortunaly doesn't boot so i can't use manual SSPL
lol
go to htc site
download latest rom for blackstone
while it is downloading take out the battery of the phone
put the battery back in
press volume down and keep it pressed
while keeping volume down pressed press briefly on the power button
now you will enter bootloader and yu can flash the rom you downloaded from htc.com
to get the rom you have to enter serial number wich the spl will be set to so it doesnt matter wich spl is on youre phone
htc.com they always say "Sorry, this software download is not suitable for your device." and stop the download
Okay i downloaded the rom but like i said i can't updat if try i get error [294] invalid vender id
Are you able to go into the tri-colour screen (bootloader)?
with the blackstone off, you press the VOL DOWN button and press the power button.
If you are able to see the tri-colour screen your blackstone is not bricked.
just follow the steps here:
Dummies guide: flashing 1.56+ roms [v 2.0] - [HSPL][USPL]
Well good news is that if you can check your SPL, your device is definitely not bricked. Just follow guidelines in this thread to flash new rom and post further queries in that thread.
Thread closed