[Q] Boot loader - XPERIA X8 Q&A, Help & Troubleshooting

Heya!
I've a question. THat if i unlock my boot loader, and flash a new kernel, will i need to reinstall my current rom, or its not important?

It is depending on the fact that your current rom is compatible with the kernel or not?
Gingerdx-->Alfs or ldx
minicm7.2-->naA kernel.
Hope this will help ...
Sent from my E15i using xda premium

Straboterous said:
Heya!
I've a question. THat if i unlock my boot loader, and flash a new kernel, will i need to reinstall my current rom, or its not important?
Click to expand...
Click to collapse
Just a suggestion: unlock bootloader after restoring phone with seus to base 2.1, so there will be far less (or none) problem through the procedure.
Sent from my heart using a brain )

One question, the recommended step if i want to flash custom kernel n rom is:
-flash kernel first,then rom
Or
-flash rom,then kernel..?
Sent from my E15 using xda premium

First flash kernel. I think you can do the opposite, but flashing kernel first is the best solution.
Sent from my heart using a brain )

i read that after unlocking bootloader, the xrecovery no longer works. so if i flash back my phone to 2.1, if i root and install xrecovery, will the xrecovery works..? or i must install CWM instead..?
and what i must do if i want to flash a ROM that need to be flash with xrecovery..?

Install the Dual-Mode recovery with x8Toolbox, that'll give you xRecovery AND CWM.

B.Jay said:
Install the Dual-Mode recovery with x8Toolbox, that'll give you xRecovery AND CWM.
Click to expand...
Click to collapse
ok..i already read the post.so...how do i use this..? i see alot of links but dont find any proper instructions. sorry.
can u teach me how..?

Thx for the usefull comments, and i have 1 more problem, the pcc shows that my phone is w8 (e16.) But it wrong because its e15... so i cant unlock my bootloader because the . Cmd file gives me error (cannot finde the path or aomething like that, and the flashing is aborted)
Sent from my X8

Straboterous said:
Thx for the usefull comments, and i have 1 more problem, the pcc shows that my phone is w8 (e16.) But it wrong because its e15... so i cant unlock my bootloader because the . Cmd file gives me error (cannot finde the path or aomething like that, and the flashing is aborted)
Sent from my X8
Click to expand...
Click to collapse
Használd a SEUS-t inkább. Ott kiválasztod, hogy X8-ad van, és ráflasheli az E15 firmware-jét, utána szerintem menni fog.
--
Use SEUS instead of PCC. There you can chose that you've got X8, then it will flash E15 firmware, then I think it will work.

Köszi szèpen! / thx
Sent from my X8

Related

[Q] help me, brik my x8

I help my brik x8 Ginger root with Roma Dx installed v013 and cercovo to install filter net with this tread: (http://forum.xda-developers.com/showthread.php?t=1184907&highlight=iptables 2Fnetfilter% + support) .
Can anyone help me? thanks
If you can boot in xRecovery, try making a full wipe. If that fails, restore a backup. If you can't boot in xRecovery, reinstall stock with SEUS.
LOL (help me brick my X8)
Edit: Did you flash the zip in xRec? That's not a flashable zip, it just contains some files.
Sent from my X8 using XDA App
Chris95X8 said:
If you can boot in xRecovery, try making a full wipe. If that fails, restore a backup. If you can't boot in xRecovery, reinstall stock with SEUS.
LOL (help me brick my X8)
Edit: Did you flash the zip in xRec? That's not a flashable zip, it just contains some files.
Sent from my X8 using XDA App
Click to expand...
Click to collapse
Unfortunately does not go into recovery mode with the `physical buttons so I can not make them do anything.
That leaves you no choice but to use SEUS
Sent from my X8 using XDA App
Chris95X8 said:
That leaves you no choice but to use SEUS
Sent from my X8 using XDA App
Click to expand...
Click to collapse
sorry I did not understand
wtosett said:
sorry I did not understand
Click to expand...
Click to collapse
SEUS is the Sony Ericsson default update service.
Go to this link for details on how to restore your phone to an usable condition:
http://forum.xda-developers.com/showthread.php?t=1011071
Chris95X8 said:
If you can boot in xRecovery, try making a full wipe. If that fails, restore a backup. If you can't boot in xRecovery, reinstall stock with SEUS.
LOL (help me brick my X8)
Edit: Did you flash the zip in xRec? That's not a flashable zip, it just contains some files.
Sent from my X8 using XDA App
Click to expand...
Click to collapse
i laughed at this when you put it.i thought it ment by the title to help him brick it i was about to comment 'of course i can help you' but then i read the info given and thought,either xrecovery of seus.
p.s i have never bricked my phone i have managed to install ginger dx v013 but i know how to brick it!

[Q] Flashing Kernel

Hey people,
i was reading a lot of posts and topics and i'm really really really very confuse now.
Some people say that we put the kernel file in the Flashtool folder, blablabla, and then we flash, blabla, some people say we have to change another file and make a bundle or whatever and blablabla, blablabla, blablabla! a lot of ways are told in the different topics
I just want to know exactly all the steps from downloading the kernel to turn on the phone with the new kernel (i already unlocked the bootloader sucessfully)
If theres differents steps from kernel to kernel, i just want the steps for the FXP Kernel and (if diferent) to the CM Kernel.
Thanks in advance
I did like that :
1.download kernel linuxdx
2.put ftf to firmwares folder in flashtool
3. Run flashtool
4.press flash
5. Select linuxdx kernel
6. Flashed linuxdx in less than 2minutes
7.take out the cable
8. Boot phone, install gingerdx
9.reboot
10.Enjoy new kernel and ROM
Sent from my X8 using XDA Premium App
So... what about the loader? We don't need to do nothing to that? And is that the same process to FXP Kernel?
RockitOut11 said:
So... what about the loader? We don't need to do nothing to that? And is that the same process to FXP Kernel?
Click to expand...
Click to collapse
Yes the same on fxp kernel
Sent from my X8 using XDA Premium App
with what did you install gingerdx?
0rang33 said:
with what did you install gingerdx?
Click to expand...
Click to collapse
Clockworkmod recovery?
Sent from my X8 using XDA Premium App
return to original kernel
proadi96 said:
I did like that :
1.download kernel linuxdx
2.put ftf to firmwares folder in flashtool
3. Run flashtool
4.press flash
5. Select linuxdx kernel
6. Flashed linuxdx in less than 2minutes
7.take out the cable
8. Boot phone, install gingerdx
9.reboot
10.Enjoy new kernel and ROM
Sent from my X8 using XDA Premium App
Click to expand...
Click to collapse
If I try the linuxdx kernel and want to switch back to original kernel that I am using how would I do this? Do I have to back up the kernel to use it again? If so, how would I do that?
Thank you for your help!
Just download stock kernel too, it is posted in few places on forum.
If you will not want LDX ot FXP kernel then you just flash stock one.
Remember about full wipe if any problems after changing rom or kernel.
Also stock kernel will NOT have recovery... do backups! ;]
Thank you for your help!
That "bla bla bla bla bla" way is the correct way!
RockitOut11 said:
So... what about the loader? We don't need to do nothing to that? And is that the same process to FXP Kernel?
Click to expand...
Click to collapse
If you are useing per made kernel like linuxdx.04
loader is all ready in the ftf file
If you get a file call kernel.sin then you will need. The loader.sin
And make a ftf file in flash tool
super.sense on x8
velnens123 said:
That "bla bla bla bla bla" way is the correct way!
Click to expand...
Click to collapse
i installed minicm6 on my w8.. but i need to install rom 2.3.7 on my phone.
i tried to install 2.3.5 and while booting my phone got stuck in the primary logo of cynogenmod.i am doomed.
can anyone help me out...i need to update my phone to 2.3.7
U mean no need to unlock the bootloader??
eric793tp3 said:
U mean no need to unlock the bootloader??
Click to expand...
Click to collapse
yes you need to unlock bootloader

[Q] Stucks after flashing or installing ROM.

I flashed the latest official firmware...
Than after all my attempts i can't install any ROM, except official 2.1.
Please, write me instructions how to install CM7 - i need help...
I have rooted 2.1 with xRecovery - what's next?
Go to xrecrovery choose instal custom zip from sd card hoose zip from sd card find your mini cm 7 install rom and factory reset/full wipe.
It depends on ROM. Some of CM7 works only on custom kernels, so You should first check if You will be able to unlock bootloader. Look behind Your battery - on the stick there should be something like xxWyy which will tell You the year and the week of Your board. If it's older than 11W26 (26th week of 2011) - U may unlock bootloader and install custom kernel (on Your own risk ;P). If not - You shouldn't do this and search for ROMs working on SE stock kernel
Bolussimo said:
It depends on ROM. Some of CM7 works only on custom kernels, so You should first check if You will be able to unlock bootloader. Look behind Your battery - on the stick there should be something like xxWyy which will tell You the year and the week of Your board. If it's older than 11W26 (26th week of 2011) - U may unlock bootloader and install custom kernel (on Your own risk ;P). If not - You shouldn't do this and search for ROMs working on SE stock kernel
Click to expand...
Click to collapse
Also, some ROM required CWM instead of Xrecovery, so read carefully before attempting anything.
Hmmmm
I unlocked bootloader long time ago(10WW48 on the sticker).
to przemek4113: Just installing from xrecovery gives me a unbooting phone.
I tried Froyo, but it doesn't boot too.
Then i'm flashing(Xrecovery doesn't give me a booting phone even if i recover all system) official 2.1.
This phone was bought with GinderDX on it. But latest versions need new kernels(flashing kernel bricks phone).
May be try Previous versions of GingerDX?
Really, i tried about seven customs...
P.S. I'm installing xrecovery ROM's from Xrecovery and CWM ROM's from CWM...
BEaStia said:
This phone was bought with GinderDX on it. But latest versions need new kernels(flashing kernel bricks phone).
Click to expand...
Click to collapse
Mind to elaborate where you read that "latest versions need new kernels"?
GingerDX runs on STOCK KERNEL, LinuxDX as well as Alfs. I fail to find the part in doixanh's post where it says something about forcing a certain kernel to be used.
Make sure you have an older x8 than 11w29, its under the battery. When the number is 11w29 or newer, you'll not get CM. Unlock your bootloader.
Download and flash FXP kernel. Install official CM with the kernel built-in CWM. I recommend to flash nAa kernel after install the CM, it's much better.
Sent from my E15i using xda premium
If you want CM7 you should go to this thread...http://forum.xda-developers.com/showthread.php?t=1362585
That's my fault - i was speaking about another ROM. Not GingerDX - but it doesn't boot too.
I followed advise about miniCM7.
Flashed kernel ->then wiped all(i disliked the message about ext4 - there's no this partition - probably that's the problem???) ->installed ROM. Nothing.
"nAa kernel" logo appears and then it reboots.
UPD:
I've installed GingerXperia(v19) via CWM.
Then -
I've flashed all kernel,fota and smth else(not all files from 2.1.1).
Then it booted...strange)
But i'll try to work with other kernels...
hi
i had rooted my w8 with super1click installed xrecovery and with it gingerxperia v22.today i installed v24b and rebooted.then installed chargemon zip.but after this my phone stuck at se logo ...its not even shutting down so no xrecovery or pc companion working...somebody pls help...
sreeramllb said:
hi
i had rooted my w8 with super1click installed xrecovery and with it gingerxperia v22.today i installed v24b and rebooted.then installed chargemon zip.but after this my phone stuck at se logo ...its not even shutting down so no xrecovery or pc companion working...somebody pls help...
Click to expand...
Click to collapse
Probably:
1)make a backup of all data
2)flash stock kernel
2.5)wipe
3)install custom
3.5)wipe
4)recover data
?
1.As my phone is not booting can't take back up but i have previous back up with me
2,how can i flash stock kernel ?is it with flash tool?
sreeramllb said:
1.As my phone is not booting can't take back up but i have previous back up with me
2,how can i flash stock kernel ?is it with flash tool?
Click to expand...
Click to collapse
Flash Tool - I've seen links on it thousand times on 4pda.ru, but not here - i suppose it to be in the branch about X10.
http://www.mediafire.com/?z7fmpiragbbdxdu - here is flasher.
http://depositfiles.com/files/c2gllgt6t - or here, with official firmware
It would be great if somebody could provide the step by step procedure of flashing my w8 to get past the se logo....
1)Download all archives above
2)Run flasher
3)Press "Flash" and choose necessary firmware
4)follow advices of software
5)reboot -> You have official 2.1
then
1)check your bootloader(http://4pda.ru/forum/dl/post/1227710/S1tool.7z) with this tool
2)unlock it if it is able for you
3)take root(superoneclick with debugging)
4)make xrecovery
5)install any xrecovery zip
or
alt 5)make CWM
alt 6)install any CWM zip
or
install kernel
then install zip
Firstly try it from xrecovery. If you have some problems - write PM to me)
I have done it and successfully flashed as per flashtool...but now even i cant boot stuck at "sony ericsson" now the animated logo works and reboots automatically...pls help
Have you done "user-wipe" in Flash Tool???
Here is from friendly branchcontains a collection of GingerDX 013-022 and some other goodies in the "Sony Ericsson" folder - i.e. Basebands, PCC, SEUS, Flashtool)
http://www.mediafire.com/?eca0sualnao4c4c
Thanks to B.Jay
Atlast with full user data wipe in flash tool I recoverd my phone...THANKS A LOT!!!
Again rooted,Xrecovery and installed GX V24b-I would like to know how to enable multi touch in it please?
How to make xperia x8 able multi touch.
i want to know what i have to do to make xperia x8 able multi touch(im using gingerxperia v23 on my x8)...can anybody help me plz..i appreciate your help...
:-D
chehady said:
i want to know what i have to do to make xperia x8 able multi touch(im using gingerxperia v23 on my x8)...can anybody help me plz..i appreciate your help...
:-D
Click to expand...
Click to collapse
Ok here is a nice way how to enable it hope it helps you
http://forum.xda-developers.com/showthread.php?t=1135965
Sent from my E15i using XDA App

stuck on Splash screen!

Hello, im helping a friend root he's phone.
He is stuck at the "Sony Ericson screen"
This is what we have done so far:
- install superuser/bussybox
- Custom recovery (CWM)
He then went into CWM and clicked:
- backup nandroid
- delete dalvik cache
- reset factory
- install zip from sdcard: Presto ... install it...... . .. . .
- Restart phone.
it gave me an error "bad restore can't restart" then It automaticly jumped to another submenu "no" "-yes -- restore CWN" underneath a warning: may not able to access the restore" I clicked yes and it restarted but never got further then booting
xologist said:
Hello, im helping a friend root he's phone.
He is stuck at the "Sony Ericson screen"
This is what we have done so far:
- install superuser/bussybox
- Custom recovery (CWM)
He then went into CWM and clicked:
- backup nandroid
- delete dalvik cache
- reset factory
- install zip from sdcard: Presto ... install it...... . .. . .
- Restart phone.
it gave me an error "bad restore can't restart" then It automaticly jumped to another submenu "no" "-yes -- restore CWN" underneath a warning: may not able to access the restore" I clicked yes and it restarted but never got further then booting
Click to expand...
Click to collapse
have u tried to use SEUS?
we fixed it.
I dont have this phone, so I didnt know you needed to have custom kernel and unlocked baseband.
How can I get the:
1. Latest baseband
2. Unlocked bootloader
to unlock the bootloader you have to check This
for latest baseband update the phone with Update Service
HashiKyu said:
to unlock the bootloader you have to check This
for latest baseband update the phone with Update Service
Click to expand...
Click to collapse
Thank you.
Where can I find this kernels
nAa AND ALFS KERNEL ?
or do they come with the ROM and automatically flash?
you can find in one of the Development Thread, you have to flash it first with flashtool then you can flash the ROM via CWM..
U means u didn't install X recovery.... If u install cwm its possible u having this problem... Cwm only work on stock rom.... Use flash tool and repair.. Install X recovery....i installed it too.. I got the same before, though it was on that Site.. This will work on stock rom
Sent from my E15i using Tapatalk 2
xologist said:
Thank you.
Where can I find this kernels
nAa AND ALFS KERNEL ?
or do they come with the ROM and automatically flash?
Click to expand...
Click to collapse
here for the nAa not ICS kernel
http://forum.xda-developers.com/showthread.php?t=1350484
and Alfs
http://forum.xda-developers.com/showthread.php?t=1340861
everything that u need, just search on android original development
bandarigoda123 said:
U means u didn't install X recovery.... If u install cwm its possible u having this problem... Cwm only work on stock rom.... Use flash tool and repair.. Install X recovery....i installed it too.. I got the same before, though it was on that Site.. This will work on stock rom
Sent from my E15i using Tapatalk 2
Click to expand...
Click to collapse
it's work on custom rom and kernel too,, i used it till now..
HashiKyu said:
it's work on custom rom and kernel too,, i used it till now..
Click to expand...
Click to collapse
I meant on Stock kernel

Revert to Stock Kernel & ROM issue!

Hi Guys,
I have my x8 phone running on nAa's latest v6 kernel with ZenceFil ROM(GB 2.3.7) with ofcourse an un-locked bootloader. But now i want to move back to stock settings.
I had made a backup using xRecovery before installing these mods, so my question is, how to I restore that xRecovery backup along with the stock kernel which i already got from the unlock bootloader thread??
I tried flashing the stock kernel but then the phone just get's stuck in the boot logo page with Sony Ericsson logo, can't even open the recovery, which i guess is not included in the stock kernel file.
I tried installing xRecovery by copying its files to /system/bin but still i have CWM as recovery!
Please advise...
p.s. I saw this thread, but the solution provided there is not working for me as PCC is not helping, it juts say's no s/w found for your device. Also I don't want to lock the boot loader.
Flash stock 2.1 trough flash tool>root it>instal xrecovery and then restore backup.
iks8 said:
Flash stock 2.1 trough flash tool>root it>instal xrecovery and then restore backup.
Click to expand...
Click to collapse
I have downloaded the stock 2.1 rom but how do i flash a ROM using flash tool? I don't see that option..
Flash it like kernel.
Sent from my GT-P3110 using Tapatalk 4
NAA6 is using difrent system-data partition size. If you want to move to other kernel you need first boot into cwm and format data and system partitions, then flash other kernels.
You can also flash your phone with SEUS and you will have stock rom-kernel like you had when you bouth the phone (if your bootloader was unlocked SEUS will leave it unlocked).
Stock rom and kernel you can flash using Flash Tool, just move the ftf file (for exemple 2.1.1.C.0.0.ftf) move this to the FIRMWARE flashtool' folder. Open flash tool and click on the "lightning" icon, (on old version click on flash) and select flash mode. Turn off the phone and flash it like a normal kernel.
But the stock rom that i downloaded has no ftf file! It's a normal backup have 4 .img files.. how do i flash that?
Sent from my Canvas 2 using XDA Developers App
You could use SEUS. It will install the newest firmware for x8 and it won't relock bootloader (for me it don't relock it), but you have to root your phone and install xrecovery one more time.
AndroidNotMaster said:
You could use SEUS. It will install the newest firmware for x8 and it won't relock bootloader (for me it don't relock it), but you have to root your phone and install xrecovery one more time.
Click to expand...
Click to collapse
Thats way i do it. Nice and easy way
Sent from my X8 using xda premium
Thanks will try that.. Can you please provide a link from where i can get SEUS
Sent from my Canvas 2 using XDA Developers App
ibshar said:
Thanks will try that.. Can you please provide a link from where i can get SEUS
Sent from my Canvas 2 using XDA Developers App
Click to expand...
Click to collapse
Search here
http://www.google.co.in
Sent from my iPhone :silly: don't flame me
wanna hang out with us? click here
stock kernal for canvas 2
I have been using canvas 2 from the past 3 months and I have flashed a custom kernel in it and now I get a error-
"Can't connect to camera" whenever I try to run it
Please help me by giving sugetions to fix it or
Please please please give me a link to the stock kernal
I am using thunder zap for now and its horrible
Please help me its urgent.:crying:
This is not the correct thread to post ur query, please move to the Micromax A110 thread and post there.. You also need to specify which rom you are using!
Sent from my Canvas 2 using XDA Premium 4 app

Categories

Resources