Broken connector for touchscreen on logic board - LG Optimus Black

Tried to change the front glass of my OB i bricked the connector for the touch screen.
Has anyone an idea how to fix it??

That is awkward. That i think it's a card edge connector, you can try your luck on google, or take a look here or better here..
Good luck.

Sorry for giving bad news, but the connector itself its OK, the problem is around the copper tracks inside of it.
In the image I can see that you pulled up too much from the connector, and due this force, the cooper tracks broke up.
Its really hard to fix.. if you have good soldering skills, you can download the service manual and see where the tracks go, and fix by soldering very small wires.
I had problems too, with the connector that connects the usb, power button and earphones. It had dropped alone inside the phone, due poor soldering quality.
So, nothing was broken, and I could solder it back. But your case is very different.
I guess that the only fix for most users is a new board.

You need a hot air solder gun for that job. Or at least a very thin metal one, but it will be difficult anyway. I think using a hot air one might help you to fix the copper tracks, it's not necessarily to have great skills.

Related

Diamond Stopped vibrating

My Alltel Touch Diamond stopped vibrating. Since I did not get it from Alltel directly...they will not replace it even though it is only 3 months old. Contacted HTC as well as PCD and no help there. Is there anyway I can fix this myself?
TIA
Go to eBay and search for 'htc diamond vibrator'. There are around $45. I never use the ringer so not having vibrate mode is killing me too.
possiblility
the ebay "vibrators" for diamond are for the gsm versions, not the cdma. note that they are laid completely differently. here's a pic of cdma (ripped from someone who knows)
ftp://ppcgeeks.com/Diamond/Users/snovvman/DSCF2199.JPG
now, in my case, kind of neat. if you open the case up that far (four screws on inside, that's all), you'll notice that the vibrator motor can be detached from mainboard relatively easy through the two pin (black/red) header. you can test the vibrator motor with like some AAA 1.5V battery or something. in my case it worked, so drats, that means that the driver could be blown.
however, i looked real closely, above the header are discrete components, like a tantalum capacitor (surface mount), super tiny, and something that didn't make sense--a cold solder blob over one land pad (but not the other, ... perhaps there was one at manufacture time and it fell out??)
anyways, htc apparently intended for either an inductor or a short (0 ohm resistor) at that land pattern. sometimes they cheat and just manufacture it as with a blob of solder. in this case part of the blob fell out. hence, no connection to the vibrator motor header.
i put blob in and i was in business.
note that these are super tiny. DO NOT ATTEMPT without sufficient tools (magnifying jig, really fine tip soldering iron)
...
OF COURSE before you do ANY of this, try a hard reset first.
Thanks! I almost wasted $45.
pictures
Could you take some pictures of the areas you soldered? Im also trying to fix mine.
Also, to test the vibrator, did you just take two wires and put it on each end?
Sorry for bringing back to life this old threat but this appear to be a very common issue among diam500 owners and nobody knew what to do apart from swap it (if it still in warranty which by 3rd quarter 2010 i really doubt someone still has it)
i googled around lots of forums and this was the only one with a real answer surprisingly this was also the one with the less replies... i confirm what chnhnm said THERE IS A 0 OHM RESISTOR THAT FELL OFF(perhaps caused by the vibration itself and real poor quality soldering from htc in this specific resistor) when i gutted my diamond the resistor was still there sticked to the vibrating motor connector in the mainboard i tested it with a multimeter and confirmed it is a "0 ohm one" real tiny color black)
once again as chnhnm said i just put blob in and it worked like a charm
so there is a relatively easy fix here (if u have the tools and some soldering skills) i strongly recommend you to try this as your last resort
will post some pics later
im uploading a picture of it before i applied the blob (the resistor is missing) this is the best one i could get i hope u cant see it
elamodelmerol said:
im uploading a picture of it before i applied the blob (the resistor is missing) this is the best one i could get i hope u cant see it
Click to expand...
Click to collapse
Thank you for this! I will do this soon when I get a soldering iron.
Ok, I tried doing this, but it is hard to solder it. Everytime I try to put the blob there, the solder attaches to the iron and doesn't stick to the connection on the board.
Can I get some help on how to keep it on the connection instead of melting and sticking to my iron?
sorry for the late reply...
well i don't really know how to solder either but i have learnt something by just giving it a try(and a few youtube videos xD) ...this is how i did it.
first off make sure the surface is clean wipe it if needed with acetone(don't flood the board) and a cotton swab (that will remove the grease and dirt it may have)
be careful not to apply to much solder on the iron tip...just use a little bit more almost nothing than the needed to coat the tip...
do not overheat ur iron that will cause the metal to oxidize quicker (oxide prevent the metals from joining) unplug the iron as soon as it is hot enough to melt the solder
use some soldering flux be careful not to add too much just enough to cover that tiny area (u can use a needle) this cleans even more the area and prevents the metal oxidation
now u just need a steady hand and eagle like vision
even after following this directions i still find it hard to achieve for a noob like me maybe i just got lucky...xD
if you are out of luck maybe u can buy one of this conductive ink pens and that way u just have to draw fine line or should i say a dot. Or u can try using a pencil (graphite is a relative good conductor) but that didn't work for me...
Good Luck Mate

[Q] Streak replacement capacitive buttons.

I damaged my Capacitive buttons (flex circuit).
Can anyone recommend where to get a replacement part?
Lol. I did the same thing. Ladies and gentlemen please wait for the plastic tool to arrive in the mail before you start trying to disassemble your streak! I used a screwdriver and it cut through the flexible circuit card. Contemplated fixing it, but there`s five tracks on the circuit board!
I got a quote from an ebay seller in the UK for the capacitive buttons and plastic bezel. 90 pounds plust postage. What a rip off! I ended up buying a complete streak from ebay. It was locked to O2 and had the lcd bleeding problem, but perfect for me. Keep your eye out.
In the meantime, install softkeys from the market. It is a replacement home/settings/back button. A little inconvenient, but keeps you going while you bide your time on evilbay.
Sent from my Dell Streak using XDA App
printed circuits
My first streak also has a broken capacitive circuit board, didn't use this plastic tool for disassembling..
Now i use a old modified tooth brush
Was ready to ask a flexible board manufacturer what it would cost to reproduce such a circuit but for now i'm also using softkeys..
Maybe if we get 100 people together who needs one of those capacitive button circuits its worth asking a reproduction?
Thanks for the inputs. I got the key to work again after some fiddling. I'm just waiting for it to inevitably fail. I'll probably just get a new phone when that happens.
how do you get it broken? not that i wanted too, but it sound strange to me
Sent from my Dell Streak using XDA App
Pretty easy... First time pulling it apart, had not seen any videos of the process. Fixit. Com (OR IFIXIT?) wasn't that comprehensive. Of course I was overtired and of course used a small screwdriver instead of a plastic removal tool.
Excuses, excuses. The screwdriver ultimately was the wrong thing.
Sent from my Dell Streak using XDA App
Does anyone know where i can buy the Streak front 4 buttons and volume rocker buttons ribbons ?
http://www.dellstreakrepairs.co.uk/spares.html
I broke my capacitive button ribbon cable, anyone have any luck finding replacements? I'm going to try to repair it.
Wheeew, just finished repairing my broken cap buttons. Most nerve-wracking soldering job ever.
I managed to tear through 5 contacts on the flex PCB when disassembling the Streak because I didn't bother to read the obvious warning about this on ifixit Also, I was taking the week-old device apart for no good reason, so I had it bloody coming, really. Anyway, even with a high-quality soldering iron and a stereomicroscope this repair was a massive pain, but it is doable.
I think it should be possible to repair even a completely broken ribbon - I would scrape off the plastic off the ends of the tracks and then glue the underside of both halves of the circuit in place (or tape together if not possible). Then you need to tin the tracks with solder - plenty of flux helps. After that it's the difficult matter of bridging the broken tracks with solder blobs or tiny pieces of wire while not shorting across them. Finally a layer of epoxy to secure it all. Not even worth attempting if you don't have a really good soldering iron and a microscope. Can't use too high a temperature or the plastic melts. I did the repair with the phone assembled fully except for the bottom panel, flex PCB attached to phone - the broken area was still accessible for me and this way reduces the risk of breaking contacts during reassembly.
Hope this helps someone!
Posted in error
is it available now . coz i searched all through the internet and couldnt find the home and back buttons strip .
DashingGentleman said:
Wheeew, just finished repairing my broken cap buttons. Most nerve-wracking soldering job ever.
I managed to tear through 5 contacts on the flex PCB when disassembling the Streak because I didn't bother to read the obvious warning about this on ifixit Also, I was taking the week-old device apart for no good reason, so I had it bloody coming, really. Anyway, even with a high-quality soldering iron and a stereomicroscope this repair was a massive pain, but it is doable.
I think it should be possible to repair even a completely broken ribbon - I would scrape off the plastic off the ends of the tracks and then glue the underside of both halves of the circuit in place (or tape together if not possible). Then you need to tin the tracks with solder - plenty of flux helps. After that it's the difficult matter of bridging the broken tracks with solder blobs or tiny pieces of wire while not shorting across them. Finally a layer of epoxy to secure it all. Not even worth attempting if you don't have a really good soldering iron and a microscope. Can't use too high a temperature or the plastic melts. I did the repair with the phone assembled fully except for the bottom panel, flex PCB attached to phone - the broken area was still accessible for me and this way reduces the risk of breaking contacts during reassembly.
Hope this helps someone!
Click to expand...
Click to collapse
I think I may attempt this...$40usd for a new assembly is a bit high...
You can find the top/bottom parts on Ebay and on Lingosbox.com
I've purchased some spare parts for other phones on lingosbox - they are not genuine oem parts but for this price, it's a bargain for replacement parts that are rare/difficult to find. There's some delay(15-27days) but everything has arrived without any problem.
good to know someone found it cheaper

Replacing ear piece speaker (complication?)

So I'm in the process of replacing the ear piece speaker. It has always acted up but finally completely went out when I dropped the phone today. Tore the phone apart and pulled the bad one out, and put it back together, so for the time being it's a phone with no speaker, but strangely now the rear camera doesn't work either.
So I'm curious, maybe I still don't have the ribbon cable from the camera seated correctly. But do you think maybe the camera and speaker are on the same circuit and without the speaker in there the camera won't work?
The ear piece not working can usually be fixed by bending the metal pins. I've managed to fix3 Droid's this way. that being said, I don't think the camera has anything to do with the ear piece.
Check if you've inserted the ribbon properly. The ribbon goes in pretty deep. It's easy to make a mistake when connecting the ribbon.
You wouldn't have some instructions for that procedure, do you? Or is there an iFixit video? Have the same problem with the speaker.
Sent from my DROID4 using Tapatalk now Free
Bumping this old thread in the event that someone in the future finds it useful. Obviously, replacing the speaker will VOID YOUR WARRANTY in every way possible, and if you're not careful will ruin your phone! But, if you're like me, your D4 is long out of warranty and it'll be a cold day in hell before you give up your keyboard.
That being said, I just replaced the speaker in my D4, after the stock speaker fizzled and died after almost 2 years. Every now and then it would "fuzz out" and I'd gently tap the phone against my head (which I'm sure looked quite comical) and it would stop. Finally the speaker gave up the ghost entirely and it was nearly impossible to hear. I used resources from this site to guide me in taking it apart.
You'll need a torx T5 and T3 driver - DO NOT try to use any substitute drivers if you don't have an official T5 or T3, like I did - you will strip the screws (they strip VERY easily) and you'll need to bust out the dremel to drill/grind away the screw, or buy a whole new LCD/digitizer assembly for $~70 (which, as of this posting, are getting harder to find). You might think that you can fudge it with an eyeglass repair flathead driver, but you can't. Trust me. T3 and T5 drivers are cheap online, do it right.
For the actual replacement speaker itself, I got a speaker for a Nokia Lumia 610 on ebay for about 4 bucks (free shipping!). It's almost identical to the stock D4 speaker, but it looks to be a little better quality and the actual place where noise comes out looks to be ever so slightly bigger. It "sits" in a little pocket in the outer housing/screen digitizer, held in place by the flex cable. You'll see once you get there.
Make sure both the dual snap connector that connects the mainboard to the screen/digitizer is securely fastened, and also make sure that the tiny snap connector that goes from the screen to the digitizer itself is securely fastened as well - this second snap connector is up by the notification LED. I scared myself when I re-assembled everything and my touchscreen didn't respond. Also, when you're working up by the notification LED, there's a small piece of white-ish rubber that sits between the actual LED itself and the little hole where light comes out on the front of the phone. It's crucial that you don't lose this - the LED is a few mm offset from the hole, and this piece of rubber glows and creates the notification light that you see on the front. Without it, no notification light.
Be careful with the mainboard, replacement units are very hard to find and will only get rarer as the D4 ages. It's basically the heart of your phone.
Tweezers and a "safe-open pry tool" (basically a piece of soft plastic to ease apart the pieces of your phone) make this process easier as well.
Another note: there are 2 hidden T5 screws behind the bezel that surrounds the rear camera and flash. When you go to peel this up, you'll probably ruin it - this is poor design IMO, and mostly inevitable. Good news though, replacement camera bezel parts are available online for a few bucks.
All in all, this process isn't difficult, but requires really good light (super bright lamp or headlamp) and will give you a greater appreciation for your phone and how it's both a magical little black box as well as just a collection of shiny bits.
Good luck!!
Khiraji said:
You'll need a torx T5 and T3 driver - DO NOT try to use any substitute drivers if you don't have an official T5 or T3, like I did - you will strip the screws (they strip VERY easily) and you'll need to bust out the dremel to drill/grind away the screw
Click to expand...
Click to collapse
Listen to him. I learned this the hard way and that is precisely what I had to do. Taking a dremel to my cell phone... I never want to sweat bullets like that again.

Headphone jack: how do I fasten it?

Heyho,
my headphone jack was broken, so I bought a new one and wanted to replace the broken one.
Removed the old one according to this video: https://www.youtube.com/watch?v=jbvYl2JwWG4&index=3&list=PLM3XYRzu8pIE02IZ-4RQ43CTlYs3pDzej (at 2:55min)
and wanted to insert the new one according to this one: https://www.youtube.com/watch?v=ldXrIFDgcgU&list=PLM3XYRzu8pIE02IZ-4RQ43CTlYs3pDzej&index=5 (at 0:10min)
However, how do I fasten it? if I just stick the jack in place it's loose, there is no glue or clip or anything.
Anyone ever done this or any ideas? Tried some all-purpose glue, but it's not really very stable.
Thx!
There is a lil bit of two sided tape on it but its of not much use.......once you screw the black bracket holding everything.... After installing the board it should stay in place...am having no issues so far... Been a month or so..... But you won't get your water proofiness(or whatever its called)....
sorry for the delay, that worked, thanks!

How can I remove the back from a Doogee Y6?

Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Droidriven said:
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Click to expand...
Click to collapse
Already search extensively, no luck so far. Prefer not to 'experiment' and wreck the thing!
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Bro check YouTube very well... it there
Sent from my iPhone using Tapatalk Pro
I can help you.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Did u fix it? I can help you. I opened the phone like 10+ times.
Hi, I have the same problem, I need to open the phone to replace the camera but did not manage to find anything on youtube. Would u please help me? Thanks
Monster 00 said:
Did u fix it? I can help you. I opened the phone like 10+ times.
Click to expand...
Click to collapse
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
kiwironnie said:
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
Click to expand...
Click to collapse
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Monster 00 said:
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Click to expand...
Click to collapse
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
kiwironnie said:
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
Click to expand...
Click to collapse
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Monster 00 said:
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Click to expand...
Click to collapse
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
kiwironnie said:
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
Click to expand...
Click to collapse
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Monster 00 said:
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Click to expand...
Click to collapse
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
kiwironnie said:
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
Click to expand...
Click to collapse
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Monster 00 said:
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Click to expand...
Click to collapse
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
kiwironnie said:
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
Click to expand...
Click to collapse
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Monster 00 said:
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Click to expand...
Click to collapse
Brilliant, thanks again! No need for a video, as your explanation is very clear and should be obvious to others after they get the back off the phone. Having recently removed a glued battery from a Kindle, it was a hell of an arm wrestle! Hopefully it will be a bit easier with the Y6. I have a flat nylon spudger with a rounded edge, which should be able to lift the battery without puncturing it. Upgrading the speaker at the same time could be a useful hack, if a better one can be found that fits. Although don't know if the impedance is the same for most phone speakers.
Will post results here including any lessons learnt. Cheers Ron.
The replacement usb charge board arrived, purchased from this guy: http://www.ebay.com/itm/New-Origina...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 Posting the url as the service was excellent. Very well packed in its own cardboard box and sent by registered post. So I would buy from him again, even if he is a little more expensive than some on AliExpress.
To fit the new board, the case was opened, as described above and the battery removed. To remove the battery, two screws need to be removed from a metal plate covering the battery connector. The battery ribbon cable connector can then be levered up with a small flat screwdriver blade. It's a effectively a plug with a push fit onto the connector so just pops off.
To remove the battery I used an old credit card, sliding it underneath at one edge of the battery, then gently pushing it forward to release the battery bit by bit, from it being glued to the base. This shouldn't need a lot of force and it is important to avoid snagging the ribbon cable that runs under the battery.
The black plastic cover that houses the speaker and covers the charging board was then removed by unscrewing 4 screws. On my phone one screw had a white plastic covering, into which a cross head jewellers screwdriver can be pushed to grip the screw. The charger board was then exposed and the two speaker wires and two wires from the vibrator were unsoldered using a fine tip iron. The plastic cover was then fully removed. The black rubber tape covering the ribbon cable connector was scraped away, the connector unlocked and the ribbon cable removed. The antenna connector attached to the charger board was then levered off using a small flat bladed screwdriver. The charger board itself was then pulled out. It is held in place by tiny plastic tabs on either side and was a bit of a fiddle to remove.
The old charger board has some Kapton or similar tape underneath, which the new board didn't have. So I applied some similar tape to the new board, but this may not be essential. The new board was then fitted back in, again a bit of a fiddle. I found the best way was was to insert the right hand side of the board first under its tab (looking at the inside of the phone from the charger end), with the board rotated slightly anti clockwise, then pushing the left hand side forward (rotating clockwise) and under the left hand tab so that it effectively clicks into place (not much of a click). The rest of assembly was the reverse of disassembly. Soldering the 4 wires (polarity is marked on the board), pushing the ribbon cable squarely into the connector and locking it. Nearly forgot to push the antenna connector back on!
Replaced the back and the new charge board worked perfectly. What a relief! Thanks again to Monster for getting me started. Cheers Ron.
Hello everyone,
I have every tool needed to fix any problems on any mobile phones. But after fixing my y6, I have thought that a T5S would be piece of cake. But it's not.
Any ideas if I can just remove the broken digitizer to attach the new one or is it glued to the LCD like all new Samsung models?

Categories

Resources