Hi all,
unfortunately i have broken the screen of my Note, completely, no touch response and something like this.
I'm be able to connect the phone with kies and recover all data, but with kies it's impossibile to reset the firmware.
I want to sell my phone as broken phone but i need to do an hard reset to be sure that all personal data is deleted,
how i can do this?
Thanks a lot guys
is the screen lil bit visible?
nokiamodeln91 said:
is the screen lil bit visible?
Click to expand...
Click to collapse
no completely black with no touch response
what rom were u on. If u r able to connect to kies the. u should be able to see the phones drives in my computer as well. u can delete some data from there.
I guess u can do it using adb
If you need to do factory-reset,follow the following steps:
Download this
Open ODIN
put factory_reset.tar.md5 in PDA section and donot check/uncheck anything else...
Put your phone in download mode and connect it to PC.
hit start and it will flash and reboot.
And the device will be factory resetted
ODIN is attached in this post if you need it
This is a very good news, just 2 questions:
1. to put my phone in download mode i have to switch on the phone keeping pressed "volume down" "home" and "power" after just press volume down to enter in download mode, is that right ?
2. if i do the step 5 and the phone is not in download mode what happen?
the screen is completely black and i'll be blind when follow this steps
maybe i have done something wrong but i don't know what...
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> factory_reset.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
duombo said:
maybe i have done something wrong but i don't know what...
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> factory_reset.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It failed at setting up connection...is kies running at background???if yes,stop its service and try again...
Sent from my GT-N7000 using xda app-developers app
duombo said:
This is a very good news, just 2 questions:
1. to put my phone in download mode i have to switch on the phone keeping pressed "volume down" "home" and "power" after just press volume down to enter in download mode, is that right ?
2. if i do the step 5 and the phone is not in download mode what happen?
the screen is completely black and i'll be blind when follow this steps
Click to expand...
Click to collapse
Step 1 is wrong
Volume down + home +power
That will lead to warning Page
Here you have to press volume up (you wrote down) to enter download mode,
And looking to log device added two times, this corelate your mistake , because you are pressing volume down in warning Page that will reboot your device normally instead of download mode and after booting it gets added again
One thing I want to add, the file you are flashing will raise flash counter, so if you are covered under warranty, this may voids warranty.
Alternatively you can flash stock rom file for CSC tab, that will erase everything.
Sent from my GT-N7100 using xda premium
dr.ketan said:
Step 1 is wrong
Volunteer down + home +power
That will lead to warning Page
Here you have to press volume up (you wrote down) to enter download mode,
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
he he.. r u using swiftkey?? damm! autocorrect
---------- Post added at 02:18 AM ---------- Previous post was at 02:17 AM ----------
but u correctly pointed it out
Oohhh that idiot swift key, you also have pointed out correctly
Sent from my GT-N7100 using xda premium
dr.ketan said:
Step 1 is wrong
Volume down + home +power
That will lead to warning Page
Here you have to press volume up (you wrote down) to enter download mode,
And looking to log device added two times, this corelate your mistake , because you are pressing volume down in warning Page that will reboot your device normally instead of download mode and after booting it gets added again
One thing I want to add, the file you are flashing will raise flash counter, so if you are covered under warranty, this may voids warranty.
Alternatively you can flash stock rom file for CSC tab, that will erase everything.
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
I think it wont raise the counter because its just an empty data partition and some stock rom contains this.As far as I know only flashing modified kernel will raise the counter.But today evening i will test to confirm it
Sent from my GT-N7000 using xda app-developers app
I don't think counter matters at this moment.. He wants to sell the phone so he wants to delete data.
vijai2011 said:
It failed at setting up connection...is kies running at background???if yes,stop its service and try again...
Click to expand...
Click to collapse
thanks i will try again, btw yes in pc was running some kies process i will try to kill them
dr.ketan said:
Step 1 is wrong
Volume down + home +power
That will lead to warning Page
Here you have to press volume up (you wrote down) to enter download mode
Click to expand...
Click to collapse
ok, thanks for correct my mistake
nokiamodeln91 said:
I don't think counter matters at this moment.. He wants to sell the phone so he wants to delete data.
Click to expand...
Click to collapse
Right, i only need to erase my personal data, after selling the phone, the guy have bought my phone have a new screen of Note and when he repair the screen than he will be able to flash with what he want, i want just be sure to erase all of my personal stuff
Thank you very much guys i will keep you updated
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> factory_reset.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> data.img
<ID:0/010> NAND Write Start!!
<ID:0/010> Transmission Complete..
<ID:0/010> Now Writing.. Please wait about 2 minutes
<ID:0/010>
<ID:0/010> Receive Response from boot-loader
<ID:0/010> Complete(Write) operation failed.
<ID:0/010> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Guys i don't know what's wrong now... any help?!?!?
Don't worry the 2nd time go ok ))
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> factory_reset.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> data.img
<ID:0/010> NAND Write Start!!
<ID:0/010> RQT_CLOSE !!
<ID:0/010> RES OK !!
<ID:0/010> Completed..
<ID:0/010> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/010> Removed!!
OK, the last question (sorry for all of this trouble, and for my bad english), now, with this operation, i'm SURE that all of my data was deleted from the phone, right?
duombo said:
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> factory_reset.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> data.img
<ID:0/010> NAND Write Start!!
<ID:0/010> Transmission Complete..
<ID:0/010> Now Writing.. Please wait about 2 minutes
<ID:0/010>
<ID:0/010> Receive Response from boot-loader
<ID:0/010> Complete(Write) operation failed.
<ID:0/010> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Guys i don't know what's wrong now... any help?!?!?
Click to expand...
Click to collapse
I think you must be doing something wrong...
I downloaded the file which i uploaded(to verify that its ok) and flashed it with Odin and The result is pass..Log is here..
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> factory_reset.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> data.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
Attached a pic too...Maybe you doin something wrong on your side???
General info:It didnt raise the counter
Edit:Good that you have passed .Yeah everything on data is wiped now.But files on sd will remain...
vijai2011 said:
General info:It didnt raise the counter
Edit:Good that you have passed .Yeah everything on data is wiped now.But files on sd will remain...
Click to expand...
Click to collapse
i removed the sd card before start this process
what is the counter? (bad question eh!? really sorry)
ok now everything is cleared and i can give my phone to the buyer :good:
btw i don't know how to say thank you at all, specially at vijai2011
duombo said:
i removed the sd card before start this process
what is the counter? (bad question eh!? really sorry)
ok now everything is cleared and i can give my phone to the buyer :good:
btw i don't know how to say thank you at all, specially at vijai2011
Click to expand...
Click to collapse
yes you can give now...
Custom binary Counter is something put up by samsung on our phones that shows them how may time we have flashed insecure (modified kernel) on our phone.It is shown in download mode.But it can be easy resetted on a rooted phone using TriangleAway app by chainfire.
And you can press thanks for all my posts if you really need to thank me .But remember you can only give 8 thanks per day
can i push "thanks" 2 times per post?
thank you very much
Related
Hi
Can somebody help me with this problem
Firstly during an official update from 2.3.6 to 4.0.4 using KIES bombed out at 4% so soft bricked is what we call it!!!
Can only boot into download mode so using odin to wack on
"N7000XXLRG_N7000DBTLRG_DBT\N7000XXLRG_N7000DBTLRG_N7000XXLRB_HOME.tar.md5"
Following message appears in Odin
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLRG_N7000DBTLRG_N7000XXLRB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> factoryfs.img
<ID:0/006> NAND Write Start!!
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006>
<ID:0/006> Receive Response form LOKE
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is there anyway I can force write to it?
Could it be the firmware that is the issue or would I get this on everything I try?
Please help
Thanks
EFCLEE said:
Hi
Can somebody help me with this problem
Firstly during an official update from 2.3.6 to 4.0.4 using KIES bombed out at 4% so soft bricked is what we call it!!!
Can only boot into download mode so using odin to wack on
"N7000XXLRG_N7000DBTLRG_DBT\N7000XXLRG_N7000DBTLRG_N7000XXLRB_HOME.tar.md5"
Following message appears in Odin
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006>
<ID:0/006> Receive Response form LOKE
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is there anyway I can force write to it?
Could it be the firmware that is the issue or would I get this on everything I try?
Please help
Thanks
Click to expand...
Click to collapse
Did you select the firmware .tar file in odin PDA tab only?
This sometimes happens due to bad download file, try flashing some other firmware, preferably GB so that you can wipe if required.
search google with 'Receive Response form LOKE" and you will find lot of people having same issue and most of them able to resolve by flashing different firmware.
jeetu1981 said:
Did you selected the firmware .tar file in odin PDA tab only?
This sometimes happens due to bad download file, try flashing some other firmware, preferably GB so that you can wipe if required.
search google with 'Receive Response form LOKE" and you will find lot of people having same issue and most of them able to resolve by flashing different firmware.
Click to expand...
Click to collapse
No I have been adding it to PHONE, is this wrong?
Anyways I just tried it again adding to PDA and this time it gets stuck on
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLRI_N7000OXXLP8_N7000XXLRB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
Any ideas?
EFCLEE said:
No I have been adding it to PHONE, is this wrong?
Anyways I just tried it again adding to PDA and this time it gets stuck on
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLRI_N7000OXXLP8_N7000XXLRB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
Any ideas?
Click to expand...
Click to collapse
Yes, its completely wrong, you should select single firmware .tar in PDA tab only. Try again by rebooting your phone and check if you have kies running, if so close it completely.
SUGGESTION- Do not flash ICS stock rom now, I am not sure what has been messed up by flashing this using phone tab (ICS phone files on GB base, not sure), best is flash stock GB firmware first, then wipe in stock recovery and flash ICS.
jeetu1981 said:
Yes, its completely wrong, you should select single firmware .tar in PDA tab only. Try again by rebooting your phone and check if you have kies running, if so close it completely.
SUGGESTION- Do not flash ICS stock rom now, I am not sure what has been messed up by flashing this using phone tab (ICS phone files on GB base, not sure), best is flash stock GB firmware first, then wipe in stock recovery and flash ICS.
Click to expand...
Click to collapse
WOW!!! Restarted phone wacked it into PDA and BAM!! started to copy over!!!
A million thank you's Jeetu1981 your a fkin diamond!!!!!
EFCLEE said:
WOW!!! Restarted phone wacked it into PDA and BAM!! started to copy over!!!
A million thank you's Jeetu1981 your a fkin diamond!!!!!
Click to expand...
Click to collapse
Cool... Consider urself lucky this time
And click on thanks is better than million thanks, lol
Sent from my GT-N7000
Dear all,
I found a new firmware on sammobile site and thought to upgrade my Galaxy note from:
N7000JPLPD_N7000OJPLP7_N7000XXLPT_HOME.tar.md5
to:
N7000JPLR8_N7000OJPLR8_N7000XXLRK_HOME.tar.md5
(Both of them for Pakistan)
First I used Odin 1.83 to flash but after about 20% the Odin turned red indicating 'Fail'
Then I searched the web and (I know it's my fault) somewhere downloaded Odin 1.85, checked all the fields on Odin, like "Re Partition- Autoboot-F reset time"
I check them all and then another mistake.... used the same MD5 file in all 3 'PDA, PHONE, CSC" and flashed again.
And also used the PIT file which was in the Odin 1.85's folder.
Now I can enter the download mode but if I try to flash the new ROM, it goes upto 20% and says something like this:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000JPLR8_N7000OJPLR8_N7000XXLRK_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> hidden.img
<ID:0/009> NAND Write Start!!
<ID:0/009> factoryfs.img
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And If I flash the older ROM it says like:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000JPLPD_N7000OJPLP7_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> cache.img
<ID:0/008> NAND Write Start!!
<ID:0/008> factoryfs.img
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help
sulemani1 said:
Dear all,
I found a new firmware on sammobile site and thought to upgrade my Galaxy note from:
N7000JPLPD_N7000OJPLP7_N7000XXLPT_HOME.tar.md5
to:
N7000JPLR8_N7000OJPLR8_N7000XXLRK_HOME.tar.md5
(Both of them for Pakistan)
First I used Odin 1.83 to flash but after about 20% the Odin turned red indicating 'Fail'
Then I searched the web and (I know it's my fault) somewhere downloaded Odin 1.85, checked all the fields on Odin, like "Re Partition- Autoboot-F reset time"
I check them all and then another mistake.... used the same MD5 file in all 3 'PDA, PHONE, CSC" and flashed again.
And also used the PIT file which was in the Odin 1.85's folder.
Now I can enter the download mode but if I try to flash the new ROM, it goes upto 20% and says something like this:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000JPLR8_N7000OJPLR8_N7000XXLRK_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> hidden.img
<ID:0/009> NAND Write Start!!
<ID:0/009> factoryfs.img
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And If I flash the older ROM it says like:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000JPLPD_N7000OJPLP7_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> cache.img
<ID:0/008> NAND Write Start!!
<ID:0/008> factoryfs.img
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help
Click to expand...
Click to collapse
Hi friend just try flashing to GB and then to any other.
Use company cable for data transfer, try with another usb port and i hope it must get cleared.
Press THANKS if it helped you
Thank you my friend, but could you guide me where to find GB? And what GB actually is? The older 2.3.6 Ginger bread?
sulemani1 said:
Thank you my friend, but could you guide me where to find GB? And what GB actually is? The older 2.3.6 Ginger bread?
Click to expand...
Click to collapse
GB actually is the older 2.3.6 Ginger
you find GB in sammobile site
If it's failing at factory.fs then you could be in longer term trouble, let us know.
Sent from my GT-N7000 using xda premium
dude... try this,,
just pull out the battery. wait for 10 secs.. reinsert. go back to download mode.. use odin 1.85 and just select the tar.md5 fine in pda section.. donot check repartion.. dont use pit file.
PS: if odin is stuck once.. u cannot continue from there.. the phone needs a reboot for another try
I read somewhere saying that flashing pit file must be accompanied by bootloader or your device might brick.
Sent from my GT-N7000 using xda premium
nokiamodeln91 said:
dude... try this,,
just pull out the battery. wait for 10 secs.. reinsert. go back to download mode.. use odin 1.85 and just select the tar.md5 fine in pda section.. donot check repartion.. dont use pit file.
PS: if odin is stuck once.. u cannot continue from there.. the phone needs a reboot for another try
Click to expand...
Click to collapse
Thanks friend.
I did it. Im ok now.
Thanks to all of you who helped me here.
EDIT: Rebooted my computer and phone and it flashed fine. Thank you for all the help. I'm off to explore the world of custom roms.
Finally decided to root my phone and install CM9 from GB 2.3.6 with the LA4 Kernel. Downloaded everything I needed as per Post 3 of this thread. Accidentally flashed the newer kernel instead of the pre rooted ROM.
Realizing my mistake, I tried flashing the correct ROM and PC Odin gives me a failure. The phone won't boot, it just stays stuck on the Galaxy Note N7000 Logo with an exclamation mark at the bottom.
Check if you have cwm (power+home +volume up) If so then flash this get the standard version, then go advanced options and reboot recovery...
After that do all wipes data/cache/Dalvik cache then flash the cm9 for n7000,then flash cm9 GApps then reboot...
After the system boots to android set it up and download triangle away and use it to get rid of the yellow triangle
If you don't have cwm then download a stock GB rom and flash it via odin... Start from scratch
Cheers
Tapatalking on my GT-N7000
what is the error pc odin giving you?
Don't quite remember anymore since it was from this morning. All I recall is the little box on the top left going red.
Could I try replicating the problem or do I risk damaging my phone?
odin won't damage the phone. As above poster said check if you have cwm, else use Odin again
nokiamodeln91 said:
odin won't damage the phone. As above poster said check if you have cwm, else use Odin again
Click to expand...
Click to collapse
No, I don't have CWM so I've been downloading a stock rom since I saw that post should take an hour with glorious third world internet. In the meantime should I fish out that error message you requested or is it not worth it at this point?
If you need all data back and everything to be working I would recommend you to flash back the same ROM you had earlier using odin.
Go back to Square 1.
Then root it from Dr Ketan's post.
as you downloading the rom. you are going to use Odin again. Let know the error
Yeap, another fail while using PCOdin.
Going to install samsung USB drivers from the file in this thread and get rid of Kies.
Here's the stuff from the little window.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLA4_N7000OXALA4_N7000XXLA4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> factoryfs.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/007> Added!!
Edit: Tried again after reinstalling drivers. Still no go.
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLA4_N7000OXALA4_N7000XXLA4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
great
Hello,
Just flashed my GT-I9070 according to the how-to of qzem with the recommended settings.
This worked out once, then I was trying another firmware, this didn't work out (phone was hanging at the Samsung GT-I9070 start-screen), so I thought: "OK, lets do the other firmware again".
So entered the download mode and tried to flash the "old" firmware again (XXLD1.tar) but it just does something very fast (not really installing) and reboots again with hanging at the start screen.
OK, so lets got to the "recovery-mode"... not possible!
Did this now a few times, but everytime the same result, just a quick full download bar and restarting with hanging.
Did I kill my phone? :crying:
ODIN look also fine...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> xxld1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> kernel.bin.md5
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/005> Removed!!
PLEASE HELP ME!!!
Thanks so much
Thomas
UPDATE:
After installing a stock ROM everything worked fine again, also recovery mode.
BUT on installing the rrotkernel.tar of qzem it again hangs at the start-screen.
So problem is reduced on that step.
So how to unlock my phone without that rootkernel???
I was also struggling with qzem's method, didn't brick it but I couldn't root it. Would be nice if someone could clarify this, I'm curious.
So I ended up with a pre-rooted firmware from diego's thread. Many links are down but since you're voiding your warranty
by rooting then what's the point in having a firmware for your country? Just keep in mind that pre-rooted should match the base one, if you're gonna do this.
tommym74 said:
Hello,
Just flashed my GT-I9070 according to the how-to of qzem with the recommended settings.
This worked out once, then I was trying another firmware, this didn't work out (phone was hanging at the Samsung GT-I9070 start-screen), so I thought: "OK, lets do the other firmware again".
So entered the download mode and tried to flash the "old" firmware again (XXLD1.tar) but it just does something very fast (not really installing) and reboots again with hanging at the start screen.
OK, so lets got to the "recovery-mode"... not possible!
Did this now a few times, but everytime the same result, just a quick full download bar and restarting with hanging.
Did I kill my phone? :crying:
ODIN look also fine...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> xxld1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> kernel.bin.md5
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/005> Removed!!
PLEASE HELP ME!!!
Thanks so much
Thomas
UPDATE:
After installing a stock ROM everything worked fine again, also recovery mode.
BUT on installing the rrotkernel.tar of qzem it again hangs at the start-screen.
So problem is reduced on that step.
So how to unlock my phone without that rootkernel???
Click to expand...
Click to collapse
Try flashing JB Roms , rooting JB is easy , download root.zip by Shaan and just flash it through recovery and u ve a rooted phone now..
Link is http://forum.xda-developers.com/showthread.php?t=2087424
Guys I was trying to root the S6 920F and my phone stuck in this cyan screen which says Downloading...Do not turn off target... I really need your help i dont know what to do.
The log from Odin3 was this:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-zeroflte-zerofltexx-smg920f.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
In my panic i put a tick on Auto Reboot on options and i pressed start again.... the logs were these:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-zeroflte-zerofltexx-smg920f.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
As i searching for my problem my fault was that i unticked Autoreboot and F. Reset time. Is there anything which i can try to do?
Please give me your help. I dont know what to do!!! thanks in advance.
dimitris_dimos said:
Guys I was trying to root the S6 920F and my phone stuck in this cyan screen which says Downloading...Do not turn off target... I really need your help i dont know what to do.
The log from Odin3 was this:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-zeroflte-zerofltexx-smg920f.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
In my panic i put a tick on Auto Reboot on options and i pressed start again.... the logs were these:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-zeroflte-zerofltexx-smg920f.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
As i searching for my problem my fault was that i unticked Autoreboot and F. Reset time. Is there anything which i can try to do?
Please give me your help. I dont know what to do!!! thanks in advance.
Click to expand...
Click to collapse
Are using an AT&T variant
Sent from my SAMSUNG-SM-G925A using XDA Free mobile app
LeKtRiCzzz said:
Are using an AT&T variant
Sent from my SAMSUNG-SM-G925A using XDA Free mobile app
Click to expand...
Click to collapse
no... i just finally solved my problem by pressing volume down and volume up and then power button for 10 sec. The phone made a little reset and finally was rooted. Could anyone tranfer this topic ''on non edge'' topics? @LeKtRiCzzz thanks for your response.
I have the cyan screen aswell.
says downloading...
ODIN MODE
Product name: sm-6920F
current binary: Samsung official
system status: official
reactivation lock: off
secure download: enabled
Knox warranty void: 0 (0x0000)
Rp swrev: 1
Kernel rp swrev: 1
And it won't reset when doing the volume down/ up power button
Odin screen
Jw89 said:
I have the cyan screen aswell.
says downloading...
ODIN MODE
Product name: sm-6920F
current binary: Samsung official
system status: official
reactivation lock: off
secure download: enabled
Knox warranty void: 0 (0x0000)
Rp swrev: 1
Kernel rp swrev: 1
And it won't reset when doing the volume down/ up power button
Click to expand...
Click to collapse
I was just having the same problem! I was just trying to fix the problem with the TouchWiz deal that kept saying "TouchWiz is not responding. Do you want to close it?" because it kept freezing my phone. So I found something online that gave suggestions on how to fix it and the screens that were supposed to pop up did not and I ended up getting into that. It sat that way for at least a half hour before I decided to search online for a way to make it turn back on. It doesn't give you an amount of time that it is supposed to take to finish so I was afraid I was going to ruin it by stopping. I did try that person's suggestion on how to reset it. I think the way they described it was confusing so it took me trying a couple different ways to figure out what they meant. Try holding down the volume up, volume down, and power button *all at the same time* for 10 seconds. That finally worked for me. Now I'm just wondering what I may have messed up by stopping the proccess. ??
No worries. I don't think you messed up anything.
I finally managed to shut it off using volume button, home button, power button. Turned it back on and everything worked the way it should.
thanks a ton
Jw89 said:
No worries. I don't think you messed up anything.
I finally managed to shut it off using volume button, home button, power button. Turned it back on and everything worked the way it should.
Click to expand...
Click to collapse
thanks a lot BRO....YOU MADE MY DAY...BROKE MY HEAD FOR SUCH A SIMPLE SOLUTION....THANKS AGAIN......
Thanks A Lot
dimitris_dimos said:
no... i just finally solved my problem by pressing volume down and volume up and then power button for 10 sec. The phone made a little reset and finally was rooted. Could anyone tranfer this topic ''on non edge'' topics? @LeKtRiCzzz thanks for your response.
Click to expand...
Click to collapse
Well, can't tell you how much it helped Thank You Thanks a lot
why did that cyan screen with the Download stuff come on in the first place?
It turns off with volume down, power etc, but when it turns back on it goes straight back into the cyan screen. Am stuck now and cant sort it. I need the phone today as I have no landline and have calls! Ta