Hi!
For some weeks my hd7 was not working well, many times it restarted and i didnt know what is the problem. Today after ive readed some blogs here, ive tryed to install a rom in hd7. But now its stuck all the time and reebot loop and i dont know what i should do.
Here is whats appearing in 3colors screen:
PD29100 SS-BC (4K)
HSPL.3.1.2250.0 (119314)
CortullaHSPL 0x07
TOUCH S1(v1.8,#1624)
Any help here! ?
Disassemble the phone and check the camera button, it must be pressed. That is one of the reasons it happens.
Related
i hope this is where i should post this.
whilst using my phone it froze,so soft reset was done then it went into tri screen
my kaiser wont go out of tri screen.i have this on screen.
kais130 mfg
spl-1.0.olipof
cpld-8
after trying hard reset and soft reset it wont pass this screen,it loads straight back to bootloader mode.i had duttys 6.1 rom on and nikis radio.
is there a solution to this problem.all was fine until this.ive searched all over for the past week and i cant seem to find a solution,so a little help is called for.id appreciate any help if possable and thank you in advance
Are you sure that your camera-button isn't stuck? Try pushing it hard few times, and then boot again.
Try flashing an official rom onto it while on that screen?
hi tried new rom and camera button isnt stuck,it seems like theres something wrong with spl-1.0.olipof.after installing new rom it boots straight to tri screen.can olipro be tacken off.just thinking of other things to revert to normal.when soft reset done it goes straight to tri screen
Try HardSPL
Why not flash it with a different SPL - like any of the HardSPLs such as Jocks:
http://forum.xda-developers.com/showthread.php?t=396922
and then flash with a new rom, suitable to that SPL?
rgds, MN
Fyi, this issue is being discussed in lots of threads @ ROM Development... I do have the same problem.
http://forum.xda-developers.com/showthread.php?t=402562
http://forum.xda-developers.com/showthread.php?t=371154&page=9
... and this one being the most recently updated:
http://forum.xda-developers.com/showthread.php?t=393337&page=29
Just to point out that the problem is solved (I think) - read here -> http://forum.xda-developers.com/showthread.php?p=2415437#post2415437
I HAVE A HTC TOUCH DIAMOND. WHEN I TURN IT ON IT DOES NOT START UP IN PHONE MODE. THE SCREEN COMES UP WITH A RED,GREEN,BLUE AND WHITE BANDED SCREEN(BOOT-LOADER) WITH
DIAM130 64M
SPL-1.38.0000
MICROP-DIAM (LED) V11
IN THE RED SECTION
PSOC-DIAM STAGE_PVT V0X32
AND SERIAL IN THE WHITE SECTION.
when i connect to computer its shows usb i have done hard reset and installed new ROM from HTC website din't work for me i also have tried Hard-SPL olinex version but they stop on 0% dn't allow me to upload to the phone for some reason
I HAVE PRESSED THE RESET BUTTON AND REMOVED THE BATTERY. STILL NOTHING WORKS. NOT TOUCH SCREEN OR BUTTONS. IT WONT EVEN TURN OFF from boot loader WITH OUT REMOVING THE BATTERY...
CAN ANYONE TELL ME WHAT to do step by step
PLEASE SOME ONE HELP ME!!!!
You could start with reading the stickies:
http://forum.xda-developers.com/forumdisplay.php?f=430
In particular, this may help you to find the root cause of your problem:
http://forum.xda-developers.com/showthread.php?t=409425
Good luck!
Hi, i was trying to do a flash on my HD7 because it's freezing everytime i open an app. So i would try a flash to see what happens, but i am just getting this [ERROR] 226 with every ROM that i am using (all of them are TMOUS by ANSAR). Can anyone help me.
News: it's not turnning on anymore. =// hope i can turn it on and try to flash again
I believe someone suggested to remove the battery for a while, try it and see
I had a similar problem while flashing one of ansars roms don't remember the error #....but what I did cause I noticed the phone was to hot from trying to flash the rom I let it cool down and tried again and everything went smooth.....hope this helps you.
Sent from my HD7 using XDA Windows Phone 7 App
i am start thinking that i bricked my HD7, unfortunetly i am fom Brazil and can't send it to repair. The strange thing is that i checked all the rooms to not use a wrong one. Really don't know what happened.
Just in case, the last room i used was the stock from TMOUS posted by Ansar. My device was 7392 already.
U can't even get it on the tri-color screen??
Sent from my HD7 using XDA Windows Phone 7 App
yes, i can't even get it on the tri-color screen. =//
i think i simply lost this phone. =/
Dam that sucks.....Does the computer beep when you plug the phone in??
no, it's dead. I sent an email to HTC to know if they can do something =P...but i don't believe so.
Oh ok.....well good luck.
i have a similar problem i upgraded t-mobile rom but after finishing phone rebooted and stuck at htc logo. can anyone help thanks
Hi,
Power off and connect your phone with battery charger to the mains
After booting and if problem persists press and hold power button until shut down
Verify that battery is charged and let me know
Regards, ansar
same problem here
i try to rom but same problem
plz help me
If you can go on the tri-color screen, you have to try out the dft rom. I used the dft rom and it worked. Please reply if it's workling!
dj.95 said:
If you can go on the tri-color screen, you have to try out the dft rom. I used the dft rom and it worked. Please reply if it's workling!
Click to expand...
Click to collapse
the dft rom can't start always 0%
hbstun said:
the dft rom can't start always 0%
Click to expand...
Click to collapse
when on the Multi-Colored screen, what does it say?
sh4d0w86.
hbstun said:
the dft rom can't start always 0%
Click to expand...
Click to collapse
try to flash another dft rom. I had this problem too, but after setting up hspl it worked.
Sent from my HD7 T9292 using XDA Windows Phone 7 App
I have the same problem with my HD7. It’s a T-mobile unlocked phone that I’ve been using for almost a year. About a month ago, I got the Mango update via Zune automatically with no problems. This morning I got a notification for a new HTC update, which I proceeded to accept. On step 9 of 10 the process hanged. Now I can´t get passed the HTC initial white screen. I’m able to reach the tricolor boot screen and are able to connect via USB with the following data:
PD29*** SS-BC (4K)
SPL-5.10.2250.0(132968) MNG
MicroP(LED) 0x07
TOUCH S1(v1.8,#1624)
I’ve tried to install the following ROMs:
RUU_Schubert_TMOUS_1.54.531.02_Radio_5.51.09.29a_22.32.50.10U_by_ansar
RUU_Schubert_TMOUS_2.20.841.02_Radio_5.65.09.11a_22.44.50.15_NoDo_by_ansar
RUU_Schubert_TMOUS_2.20.841.02_Radio_5.65.09.11a_22.44.50.15_NoDo_Signed_by_ansar
RUU_Schubert_HTC_Europe_5.10.401.06_Radio_5.71.09.02a_22.51.50.21U_Titan_Mango_7720_by_ansar
RUU_Schubert_S_TMOUS_4.05.531.03_Radio_5.69.09.29a_22.50.50.21_Signed_SCHUBERT_RELEASE
In every occasion I get the 226 FLASH WRITE ERROR. The error appears after 1% in the progress bar. That’s when I hear a beep, as if I had disconnected the phone. Then the error appears.
Any ideas????
jfvarela said:
I have the same problem with my HD7. It’s a T-mobile unlocked phone that I’ve been using for almost a year. About a month ago, I got the Mango update via Zune automatically with no problems. This morning I got a notification for a new HTC update, which I proceeded to accept. On step 9 of 10 the process hanged. Now I can´t get passed the HTC initial white screen. I’m able to reach the tricolor boot screen and are able to connect via USB with the following data:
PD29*** SS-BC (4K)
SPL-5.10.2250.0(132968) MNG
MicroP(LED) 0x07
TOUCH S1(v1.8,#1624)
I’ve tried to install the following ROMs:
RUU_Schubert_TMOUS_1.54.531.02_Radio_5.51.09.29a_22.32.50.10U_by_ansar
RUU_Schubert_TMOUS_2.20.841.02_Radio_5.65.09.11a_22.44.50.15_NoDo_by_ansar
RUU_Schubert_TMOUS_2.20.841.02_Radio_5.65.09.11a_22.44.50.15_NoDo_Signed_by_ansar
RUU_Schubert_HTC_Europe_5.10.401.06_Radio_5.71.09.02a_22.51.50.21U_Titan_Mango_7720_by_ansar
RUU_Schubert_S_TMOUS_4.05.531.03_Radio_5.69.09.29a_22.50.50.21_Signed_SCHUBERT_RELEASE
In every occasion I get the 226 FLASH WRITE ERROR. The error appears after 1% in the progress bar. That’s when I hear a beep, as if I had disconnected the phone. Then the error appears.
Any ideas????
Click to expand...
Click to collapse
Can't flash a custom ROM since your SPL is 5.X... you are pretty much stuck with what you have.
only 'hope' with OSPL 5.x, right now, is to Zune restore.
else, wait for XSPL #3 from DFT with hope it includes support for the latest SPL versions...
or jtag to 'repair' the Bootloader so you may flash an older Shipped ROM.
Zune won't recognize the phone. Nothing I can do with Zune..... Thks
---------- Post added at 09:32 AM ---------- Previous post was at 09:27 AM ----------
Ansar has a 5.x ROM which I tried, although it´s a Europe version. Any chance this could work?
RUU_Schubert_HTC_Europe_5.10.401.06_Radio_5.71.09. 02a_22.51.50.21U_Titan_Mango_7720_by_ansar
Hi guys,
I bought a HD7 a while ago, and it had been nice to use, right up to when it decided to randomly restart, and freeze. Saw there was a 7.10 update, and went for it. Half way through the update, my phone restarted, out of the blue, as the updates where installing... Typical, eh? so, before it did restart it had took a back up, Zune saw the backup and I attempted to restore. A few hours later, it had failed and the device doesn't boot past some stupid PC connection screen. Its a black screen with a mobile device, connected to a computer....
So... After a while of research, I decided to downgrade, and then flash a custom rom.
problem being, I wasn't able to get the bootloader info or OS version before the phone decided to brick its self. When I was an android user, I had bricked my phone many times, but this is so much harder.
Heres the info from what I got from the bootloader screen,
PD29*** SS-BC (4K)
SPL-5.11.2250.0(134400) MNG
MicroP(LED) 0x07
TOUCH S1(v1.8,#1624)
Can any one help me with this?
I am on o2 UK.
I have been attempting to use task 29+00. Apon using 00, I use radio 1.16 and 1.69 and both somehow restart the phone from the install percentage bar. Also been pointed to the this website, an archive of xda: http://forum.xda-developers.com/wiki/HTC_HD7/Radios
Can some one give me a helping hand and point me in the right direction?
Thanks!
davalav said:
Hi guys,
I bought a HD7 a while ago, and it had been nice to use, right up to when it decided to randomly restart, and freeze. Saw there was a 7.10 update, and went for it. Half way through the update, my phone restarted, out of the blue, as the updates where installing... Typical, eh? so, before it did restart it had took a back up, Zune saw the backup and I attempted to restore. A few hours later, it had failed and the device doesn't boot past some stupid PC connection screen. Its a black screen with a mobile device, connected to a computer....
So... After a while of research, I decided to downgrade, and then flash a custom rom.
problem being, I wasn't able to get the bootloader info or OS version before the phone decided to brick its self. When I was an android user, I had bricked my phone many times, but this is so much harder.
Heres the info from what I got from the bootloader screen,
PD29*** SS-BC (4K)
SPL-5.11.2250.0(134400) MNG
MicroP(LED) 0x07
TOUCH S1(v1.8,#1624)
Can any one help me with this?
I am on o2 UK.
I have been attempting to use task 29+00. Apon using 00, I use radio 1.16 and 1.69 and both somehow restart the phone from the install percentage bar. Also been pointed to the this website, an archive of xda: http://forum.xda-developers.com/wiki/HTC_HD7/Radios
Can some one give me a helping hand and point me in the right direction?
Thanks!
Click to expand...
Click to collapse
The goldcard/ Ycable method is your best bet and truthfully your only hope without having to use a Jtag or Riff box. The goldcard method can repair a damaged bootloader and is used while in USB host mode... The black screen indicating to connect to a P/C. This is the basic idea of it...use the goldcard method and flash a stock/shipped rom for your devices specific carrier. This should repair the bootloader and should also downgrade your spl and OS version as well, depending on what rom version you flash. At this point you can update through Zune to the current OS version. Then if you wanted to, you could use your goldcard to downgrade the spl and install rspl/hspl and flash a custom rom! Here's Shadows tutorial on how to downgrade spl, this will give you a background on how the process work and links to all the shipped/stock roms:
http://forum.xda-developers.com/showthread.php?t=1295068
This gives a good view and idea on how to make the cable:
http://forum.xda-developers.com/showthread.php?t=1676794
If you need anymore help just let us know!
Hi, i have an half bricked HD7
Hi, i have an half bricked HD7 :when i used goldcard it stayd in enter usb mod ...would u help me?
asadasad11 said:
Hi, i have an half bricked HD7 :when i used goldcard it stayd in enter usb mod ...would u help me?
Click to expand...
Click to collapse
Hi,
When it gets stuck on "Enter USB host mode" it means that it can't read the file from the SD card.
Try this -
1. Try switching around the connections of the Y cable.
2. Try a different SD card reader. This is usually the problem.
3. Make sure you renamed the .nbh file to SCHUIMG.nbh (has to be capitalized)
4. Sometimes the camera button will get stuck in and prevent the device from reading the file.
Also when the device gets stuck on "Enter USB host mode" you have to reset the device to get an active connection again... Disconnect the Y cable from the device, pull the battery and reinstall, then re-enter USB host mode and try the flash process again.
Try those and let me know if you have any success!
hi
do u know anyone with this problem, how i can contact with him/her?
hi
got the phone has a fault and unfortunately
it goes on and that's it, it stays with the white display with the HTC logo and it vibrates like 4 or 5 times in a row ....
manschmal it goes to the menu and I'll come too, and sometime it goes out again and starts all over again
Hard Reset has been made but without success ...
Now I wanted to do a firmware update or a play on but unfortunately I do not know how so if you think what you have to consider everything here ...
According bootloader I volgende data
PD29100 SS-BC (4k)
SPL-5.11.2250.0 (134400) MNG
MicroP (LED) 0x07
Touch S1 (v1.8, # 1624)
Firmware with the extension 207
I really have read here or google a lot but I did not hear it with my boot loader ...
I hope you can help me quickly on ...
love greetings
Lazyness wom't get you very far...
Use the search function before posting...