Related
I managed to fry my kaisers circuits by plugging a 4 AMP car charger into the USB power port.
It only took one second, i smelled the smoke and instantly unplugged the cable, but it was too late.
Surprisingly the device was still powered and functioning, so i didn't freak out. The battery was already dead. after around 30 seconds it died again, i walked back home and tried charging it with mains adapter with no luck.
Next morning, i took my handset to a local electronics repair shop to check it, and i told them the story. they called me back and said the motherboard needs to be replaced. and it would cost me around $470. (and its not covered by manufacturers warranty. ouch!!)
After hours of cursing and smashing my head into the steering wheel, i thought i'll pick it back and try something my self.
the part where the device stayed on even after the smoke came out led me to believe that the board is still fine. and that only the charging port got fried.
the problem is, I don't have a desk charger to charge my battery and test my theory, a disassembly guide would also be very helpful.
if the main mother board was really fried, is there any place that i can buy it from? i did some goggling around with no luck.Anything cheaper than what these guys are asking for would be great, i have a feeling they are trying to rip me off.
If any of you guys can help me out, id be grateful.
hoaxbox said:
I managed to fry my kaisers circuits by plugging a 4 AMP car charger into the USB power port.
It only took one second, i smelled the smoke and instantly unplugged the cable, but it was too late.
Surprisingly the device was still powered and functioning, so i didn't freak out. The battery was already dead. after around 30 seconds it died again, i walked back home and tried charging it with mains adapter with no luck.
Next morning, i took my handset to a local electronics repair shop to check it, and i told them the story. they called me back and said the motherboard needs to be replaced. and it would cost me around $470. (and its not covered by manufacturers warranty. ouch!!)
After hours of cursing and smashing my head into the steering wheel, i thought i'll pick it back and try something my self.
the part where the device stayed on even after the smoke came out led me to believe that the board is still fine. and that only the charging port got fried.
the problem is, I don't have a desk charger to charge my battery and test my theory, a disassembly guide would also be very helpful.
if the main mother board was really fried, is there any place that i can buy it from? i did some goggling around with no luck.Anything cheaper than what these guys are asking for would be great, i have a feeling they are trying to rip me off.
If any of you guys can help me out, id be grateful.
Click to expand...
Click to collapse
I have a brand new AT&T Tilt ( kaiserII HTC8925) for sale i can sell to you for $375.00 New In the box never been used. PM me if interested.
Sorry I can't help in this matter, but I thought i would post this here rather than start a whole new thread.
I have heard lots of horror stories of in-car chargers frying kaisers. Has anyone got an in-car charger that works?
gary.bannister said:
Sorry I can't help in this matter, but I thought i would post this here rather than start a whole new thread.
I have heard lots of horror stories of in-car chargers frying kaisers. Has anyone got an in-car charger that works?
Click to expand...
Click to collapse
Order one that is made for the Kaiser...a lot of people are trying to use old chargers just cause the tip is the same.
I got my stuff from PocketSolutions.com
Car chargers that work for the 8525 should work fine for the 8925. It just can't do that "boost" charging feature the Tilt supposedly has.
Bellfazar said:
Car chargers that work for the 8525 should work fine for the 8925. It just can't do that "boost" charging feature the Tilt supposedly has.
Click to expand...
Click to collapse
hmmm.. thats got me scared, cuz im using a razr charger for my tilt. ive used it multiple times with no probs so far...hope its not damaging my phone tho
omaralt said:
hmmm.. thats got me scared, cuz im using a razr charger for my tilt. ive used it multiple times with no probs so far...hope its not damaging my phone tho
Click to expand...
Click to collapse
That one won't damage the Kaiser, but it has only half the mA of the proper one. This can sometimes cause problems if the charge level of the battery is very low. For charging from time to time and when battery isn't near empty you will be ok.
Mike
well a quick tip would probably be checking the fuze on your charger, anything below an amp wouldnt do much damage. -.-;
4 amps fried my tilts motherboard, so watch out guys
still looking for a service manual, now that my phone is dead, i want to dissect it,
I'm using a cheapy chinese one made for an Imate Jam if that helps.
Joe
the part of the board responsible for charging is probably what went up in smoke - you probably smelt (smelled?) resistors/capacitors overheating/melting - they said a total mobo replace as that circuitry is probably all on the same board - sure you might be able to replace it yourself but i dunno - might be a bit of a mega mission what with all these micro components around on these sorts of device
fusi said:
the part of the board responsible for charging is probably what went up in smoke - you probably smelt (smelled?) resistors/capacitors overheating/melting - they said a total mobo replace as that circuitry is probably all on the same board - sure you might be able to replace it yourself but i dunno - might be a bit of a mega mission what with all these micro components around on these sorts of device
Click to expand...
Click to collapse
Yep, these devices now have multilayer boards that make it virtually impossible to do a bit of home soldering/component replacement on.
Bring back the days of my youth when we had valves (tubes in US I believe), they were nice - and kept your hands warm as you soldered away in a freezing garage
Mike
Cracked Open
I opened up the case and unscrewed my way to the burnt part of the board.
thanks to mike and the manual he posted on some other fourm
http://www.modaco.com/content/Pocke...58716/HTC-Service-Manuals-Dismantling-Guides/
This is the main board
http://img509.imageshack.us/img509/7447/ks1jj3.jpg
This is the same board from the other side with the burnt IC
http://img261.imageshack.us/img261/2717/ks2wi1.jpg
And a close up
http://img526.imageshack.us/img526/4416/ks3nv1.jpg
Closer
http://img149.imageshack.us/img149/5944/ks4lu6.jpg
Okay now i can at least see where the damage is.
Still stubborn that i am, I did not believe that this IC killed the entire mobo, so i invested in a desk charger for the battery and charged it up fully.
I just tested it now and to my surprise it WORKED!!
http://img211.imageshack.us/img211/5070/ks5vj6.jpg
Of course, my joy ride did not last for long as the device started heating up. I switched it back off once i felt the abnormal amount of heat generated.
I tried it again after it cooled down. This time I kept it for around three mins, and again it heated up, at the end of, it just shut it self off. (still heating up).
After that scary little experiment i learned few things:
1- The device motherboard is alive, there is no need to replace the entire board.
2- The burnt IC is probably meant to control the usb port and the power, therefore my usb port is useless at this stage.
3- charging the battery externally wont help much without resolving the heat issue.
I tried to look up diagrams for the devices board and the only thing i could found is this:
http://www.cdmatech.com/download_library/pdf/diagram_msm7200_cs.pdf
which is useless.
Any help would be much appreciated..
cheers
Can anyone help me with this?
http://img149.imageshack.us/img149/5944/ks4lu6.jpg
the chip burnt shown in the picture above needs to be replaced on my tytnz mobo.
can anyone give me more details about it or where can i find a replacement, all i could read on it is the (QRA) part, if anyone has a tytn II could you have a closer look, grab me a serial number maybe.
hoaxbox said:
Can anyone help me with this?
http://img149.imageshack.us/img149/5944/ks4lu6.jpg
the chip burnt shown in the picture above needs to be replaced on my tytnz mobo.
can anyone give me more details about it or where can i find a replacement, all i could read on it is the (QRA) part, if anyone has a tytn II could you have a closer look, grab me a serial number maybe.
Click to expand...
Click to collapse
anyone? lols still waiting btw
am sure most of the kaiser form viewers have a kaiser.
if any of you do can you please check that chip on your device board, i have lost mine and trying to replace it.
check if theres anything written on it, any information about it would be could be helpful.
thanks
I have plans on doing this mod, but was wondering if anyone also has tried and had either success or failure. Wondering if I should waste my time.
As far as I know the mod is done by using the Palm Pixi coil and connecting the VCC from the phone to the positive terminal on the palm pixi and grounding it somewhere on the phone.
I checked the internal of the phone to see an alternate spot for VCC that would make it easy to route the wire from the phone to the pixi coil terminal and I found a small part that would give me just enough space to run a small wire.
I am not a professional so if anyone sees me saying things that arent gonna work, let me know please.
Thanks
As a test, I am going to cut one end off a micro usb cord and plug the other end to phone.
I will solder the +5v and Ground to the pixi terminals and see if that atleast works.
What do you mean wireless charging?
Sent from my Atrix HD MAXX 4.1
Far as I know we do not have an induction service on this phone to do wireless charging. It would require a different battery and some extra to get that to work.
popfan said:
Far as I know we do not have an induction service on this phone to do wireless charging. It would require a different battery and some extra to get that to work.
Click to expand...
Click to collapse
I am talking about doing a mod, not something natively.
Good luck then. Most likely the average reader will not be able to install something as complex as wireless charging into their phone.
Hate to break it to you, but it wont work. I attempted the mod and it just wouldnt work and I did it perfectly. I work with integrated circuits, so I know what I am doing. See the photo, I used copper tape to go the two positive and negative prongs on the battery to the Palm Pixi coil.
Too bad, I really wanted it to work.
baberswallet said:
Hate to break it to you, but it wont work. I attempted the mod and it just wouldnt work and I did it perfectly. I work with integrated circuits, so I know what I am doing. See the photo, I used copper tape to go the two positive and negative prongs on the battery to the Palm Pixi coil.
Too bad, I really wanted it to work.
Click to expand...
Click to collapse
That is not how you do the mod at all, not sure why you thought it was done that way.
shanghei said:
That is not how you do the mod at all, not sure why you thought it was done that way.
Click to expand...
Click to collapse
No, you are wrong, the way I did the mod is the correct way to do it. You connect the positive and negative terminal of the palm pixi to the battery like my picture shows. The reason why it does not work is because the battery doesn't have the wireless charging chip in it like the Galaxy S3.
The wireless modding chip is called "NFC". They do sell some NFC stickers I saw on ebay, by putting one of those stickers on battery it might work but I dont feel like messing with it anymore.
Before you say I did it wrong , remember who you are talking to, I did 100 PS2 mods back in the day.
baberswallet said:
no, you are wrong, the way i did the mod is the correct way to do it. You connect the positive and negative terminal of the palm pixi to the battery like my picture shows. The reason why it does not work is because the battery doesn't have the wireless charging chip in it like the galaxy s3.
The wireless modding chip is called "nfc". They do sell some nfc stickers i saw on ebay, by putting one of those stickers on battery it might work but i dont feel like messing with it anymore.
Before you say i did it wrong , remember who you are talking to, i did 100 ps2 mods back in the day.
Click to expand...
Click to collapse
……………………………………..________
………………………………,.-’”……………….“~.,
………………………..,.-”……………………………..”-.,
…………………….,/………………………………………..”:,
…………………,?………………………………………………\,
………………./…………………………………………………..,}
……………../………………………………………………,:`^`..}
……………/……………………………………………,:”………/
…………..?…..__…………………………………..:`………../
…………./__.(…..”~-,_…………………………,:`………./
………../(_….”~,_……..”~,_………………..,:`…….._/
……….{.._$;_……”=,_…….”-,_…….,.-~-,},.~”;/….}
………..((…..*~_…….”=-._……”;,,./`…./”…………../
…,,,___.\`~,……”~.,………………..`…..}…………../
…………(….`=-,,…….`……………………(……;_,,-”
…………/.`~,……`-………………………….\……/\
………….\`~.*-,……………………………….|,./…..\,__
,,_……….}.>-._\……………………………..|…………..`=~-,
…..`=~-,_\_……`\,……………………………\
……………….`=~-,,.\,………………………….\
…………………………..`:,,………………………`\…………..__
……………………………….`=-,……………….,%`>–==“
…………………………………._\……….._,-%…….`\
……………………………..,<`.._|_,-&“…………….`
baberswallet said:
No, you are wrong, the way I did the mod is the correct way to do it. You connect the positive and negative terminal of the palm pixi to the battery like my picture shows. The reason why it does not work is because the battery doesn't have the wireless charging chip in it like the Galaxy S3.
The wireless modding chip is called "NFC". They do sell some NFC stickers I saw on ebay, by putting one of those stickers on battery it might work but I dont feel like messing with it anymore.
Before you say I did it wrong , remember who you are talking to, I did 100 PS2 mods back in the day.
Click to expand...
Click to collapse
NFC is not required for wireless charging to work. For the Palm Touchstone charger, all that was replaced on the phone was the battery cover. The Palm did not have NFC.
cajunaggie87 said:
NFC is not required for wireless charging to work. For the Palm Touchstone charger, all that was replaced on the phone was the battery cover. The Palm did not have NFC.
Click to expand...
Click to collapse
I bought the palm pixi phone trying to get this mod to work with the AHD and I remember seeing the NFC
baberswallet said:
I bought the palm pixi phone trying to get this mod to work with the AHD and I remember seeing the NFC
Click to expand...
Click to collapse
No no no.... NFC wasn't in the palm pixi from two years ago.
All the mod is is a little coil that goes on the inside of the battery cover. Our inspire/dhd phones even had the mod and there was most definitely not NFC on board.
That being said is there enough room with the battery in there to do the mod?
Youngunn2008 said:
No no no.... NFC wasn't in the palm pixi from two years ago.
All the mod is is a little coil that goes on the inside of the battery cover. Our inspire/dhd phones even had the mod and there was most definitely not NFC on board.
That being said is there enough room with the battery in there to do the mod?
Click to expand...
Click to collapse
theres definitely enough room if youre using the stock eb20, maybe not with the eb40
Even if it doesnt have NFC, you can buy the NFC stickers on ebay to add function.
baberswallet said:
I bought the palm pixi phone trying to get this mod to work with the AHD and I remember seeing the NFC
Click to expand...
Click to collapse
I had a Palm Pre Plus with the touchstone charger, and it did not have NFC. NFC is not required for this type of wireless charging to work.
Ok guys, I did the mod tonight, and could use some assistance.
I hooked up the positive of the palm pixi coil to a +5 on the Atrix HD board, and when I place the coil on the charger, it does send power to that +5 spot on board but it doesnt actually allow the phone to charge unless the phone detects an actual USB port plugged into phone.
Anyone know some way around this ?
shanghei said:
Ok guys, I did the mod tonight, and could use some assistance.
I hooked up the positive of the palm pixi coil to a +5 on the Atrix HD board, and when I place the coil on the charger, it does send power to that +5 spot on board but it doesnt actually allow the phone to charge unless the phone detects an actual USB port plugged into phone.
Anyone know some way around this ?
Click to expand...
Click to collapse
So, if you try and charge with the touchstone, and then plug in a USB cable to the phone (but the other end of the cable is not plugged into anything), then it will charge?
cajunaggie87 said:
So, if you try and charge with the touchstone, and then plug in a USB cable to the phone (but the other end of the cable is not plugged into anything), then it will charge?
Click to expand...
Click to collapse
Yes, exactly.
shanghei said:
Yes, exactly.
Click to expand...
Click to collapse
It sounds like the process of plugging in a USB cable creates a short across 2 (or more) pins that tells the phone that a USB cable is plugged in. You test for continuity when the usb cable is plugged in to see what pins are connected to each other, and then create a permanent short across these pins so that the phone thinks that a usb cable is always plugged in. But, this could also cause other problems. So, if you were to do this, I would create a short that is temporary (so that it will stay, but can be removed) and test other functions of the phone (see if data on SD card can be used, see if the phone can be turned off, etc)
I reciveved my phone yesterday and after playing with it for a few hours I charged it last night and noticed it became hot to the touch in a few minutes of being plugged in. Like burn your hand hot and there was a bit of a hot plastic smell coming off it. I unplugged it let it rest. Today I have no usb access to it. No adb, no fastboot. Lsusb shows no devices etc.
randomblame said:
I reciveved my phone yesterday and after playing with it for a few hours I charged it last night and noticed it became hot to the touch in a few minutes of being plugged in. Like burn your hand hot and there was a bit of a hot plastic smell coming off it. I unplugged it let it rest. Today I have no usb access to it. No adb, no fastboot. Lsusb shows no devices etc.
Click to expand...
Click to collapse
Xplodwild tweeted out the other day about issue with USB charging similar to this. Does the same happen when AC charging?
Is this problem similar to this guy?
Watch out for overheating!
seems to be a similar issue - it was very hot on the back side just below the camera especially I'm just afraid it got too hot and something was damaged.
This explains why google was pushing their bumpers instead of a full case I can't imagine a case would be good for this things thermal characteristics.
This happened while charging via ac when charging via usb it just seems to hold steady at whatever level the battery was.
Just out of interest, what surface did you leave it on all night?
Manipulas said:
Just out of interest, what surface did you leave it on all night?
Click to expand...
Click to collapse
I left it on a wooden desk for 5 to 10 minutes it didn't take long
It is no longer charging. I can't get it back to stock to rma I'm not happy :crying:
Woah, all other nexus 4 problems aside, this one is quite serious.
Just imagine what would have happened if you'd have left it on a easily flammable surface and wouldn't have noticed the heat. Worst case scenario might have been a fire or something like that.
If this really is a common problem (I've already seen at least two people reporting similar issues), we might see a big recall campaign quite soon.
I guess you don't really want the LiPo battery in your phone burst like this
http://www.youtube.com/watch?v=z3o_2mwRPdw&feature=youtube_gdata_player
Maybe Google should start to sell these bags instead of the bumper
Where you using the provided USB-AC adapter?
I know that my friends GS2 and GS3 got really hot when using my playbook wall charger (rated at 5v ~1.8A) :S
Heard of similiar issues with nexus 7, but the one I'm aware of is still charging.
I haven't experienced this issue yet?
I contacted google play they were quite happy to send me a replacement. Aparently they held back stock in case of a need for returns. HOWEVER they tried to charge an authorization hold on my account in the ammount of $350 I DONT HAVE ANY DAMNED MONEY I JUST SPENT IT on their ****! The only other option they said was to return it for a refund and wait a large number of weeks for orders to open up again or send it directly to LG for the same treatment ?!? I'm PISSED. The guy said that this was not the first case he'd heard of like mine didn't even ask any questions except for the serial number - I'd expect that there are going to be quite a few issues like this.
crachel said:
Is this problem similar to this guy?
Watch out for overheating!
Click to expand...
Click to collapse
Yeah, sounds like my problem. Was your microUSB port also loose/creaky like mine? I got Google to RMA me a new one. It's a shame, I love this phone and this one has no give on the screen whatsoever and no rattle. The port though and the screen flicker are another story...
Sent from my Nexus 4 using xda app-developers app
I don't have screen flicker yet and the port isn't lose I'm thinking somebody cut some corners on the voltage regulation
randomblame said:
HOWEVER they tried to charge an authorization hold on my account in the ammount of $350 I DONT HAVE ANY DAMNED MONEY I JUST SPENT IT on their ****!
Click to expand...
Click to collapse
Damn, I guess this is sorta good news for all the folks (myself included) whose banks dropped the authorization, haven't had Google recharge us, and have the phone in hand.
This phone would have been more perfect with wireless charging built in, anyone agree?
Sent from my GT-N7100 using xda premium
Yes, it would have been better, but you don't have to make a thread about this...
Sent from my Nexus 7 using xda premium
Well even though it doesn't I've found this http://www.mobilefun.co.uk/qi-micro-usb-wireless-charging-adapter-clip-p37404.htm , so technically it could. And appologies.
Sent from my GT-N7100 using xda premium
Why do you need this?
Is less comfort then wire chargh.
Sent from my LT26i
It doesn't have wireless charging but the dock that comes free with the phone in some areas doesn't need to plug into the phone and must do it wirelessly or via pins just beneath the backing I suppose
Roscobigfoot said:
It doesn't have wireless charging but the dock that comes free with the phone in some areas doesn't need to plug into the phone and must do it wirelessly or via pins just beneath the backing I suppose
Click to expand...
Click to collapse
That's sounds ok
Sent from my GT-N7100 using xda premium
Roscobigfoot said:
It doesn't have wireless charging but the dock that comes free with the phone in some areas doesn't need to plug into the phone and must do it wirelessly or via pins just beneath the backing I suppose
Click to expand...
Click to collapse
There are 2 contacts on the left hand side of the phone which get used with the dock. They are power only - not USB or HDMI. There is *no* wireless charging in this phone.
M.
mattman83 said:
There are 2 contacts on the left hand side of the phone which get used with the dock. They are power only - not USB or HDMI. There is *no* wireless charging in this phone.
M.
Click to expand...
Click to collapse
Nokias wireless charger works with all phones that have NFC, looks like i will be buying that then!
From what I've seen wireless charging is presently a bit dodgy anyway, perhaps Sony are just waiting for the tech to settle down a bit before introducing it. I don't think I'll be going for wireless charging with my N4 any time soon.
xiFIL said:
Nokias wireless charger works with all phones that have NFC, looks like i will be buying that then!
Click to expand...
Click to collapse
I don't think so. It has NFC so that you can launch a task when you put your phone to charge, but it's still based on the Qi wireless charging spec which means the phone has to be compatible too.
M.
mattman83 said:
I don't think so. It has NFC so that you can launch a task when you put your phone to charge, but it's still based on the Qi wireless charging spec which means the phone has to be compatible too.
M.
Click to expand...
Click to collapse
just looked in to it, sorry your right, i had read somewere without looking it up. My bad!
@OP: Why would you want wireless charging in the first place? It's just a gimmick it might be nice to have but, when you don't have it you won't miss it either way.
Same with 3d also a gimmick, we can live perfectly without 3d movies etc. Even though 3d movies can be quite nice to see.
Inappropriate thread.
Reported to mod.
Sent from my Droid DNA powered by Senseless DNA
kartiknnn said:
Inappropriate thread.
Reported to mod.
Sent from my Droid DNA powered by Senseless DNA
Click to expand...
Click to collapse
wireless charging is not comfortable for daily uses
I had a Droid DNA and hated the wireless charging. For one you have to pay upwards of $25-$50 for a wireless charging pad, charging takes several times longer, the phone/battery get hot while using it, which will probably lead to shortened battery life, and it's not like you can use your phone while wireless charging since if it moves more than a few millimeters off the pad it stops, versus wired where you are limited only to the length of the wire.
Isnt wireless charging jsut putting the phone on a "dock"? Like my cordless phone? or the old nokia's where u had to put it on a charging dock? Ppl behave as those it is sending microwaves to your phone within a certain radius and the phone magically charges...and if it were like that I would be afraid of nuking my insides lol
SmallsXD said:
Isnt wireless charging jsut putting the phone on a "dock"? Like my cordless phone? or the old nokia's where u had to put it on a charging dock? Ppl behave as those it is sending microwaves to your phone within a certain radius and the phone magically charges...and if it were like that I would be afraid of nuking my insides lol
Click to expand...
Click to collapse
Exactly my thought. It's wireless, but you have to put your phone on a mat... i really prefer putting my phone on a dock, and the one for Xperia Z is very good because there is no "port" that might go loose with time, just two metal pins that are touching the charger pins.
For those in doubt - here is the dock Sony will release to go with this phone - Not quite wireless charging but nearly. Having seen this it has convinced me to get the phone - the thought of fiddling with the port covers in the dark every night to conect the charger was putting me off (my gf goes to bed before me so I can't put the light on).
http://www.sonymobile.com/gb/products/accessories/charging-dock-dk26/
Spewy1 said:
For those in doubt - here is the dock Sony will release to go with this phone - Not quite wireless charging but nearly. Having seen this it has convinced me to get the phone - the thought of fiddling with the port covers in the dark every night to conect the charger was putting me off (my gf goes to bed before me so I can't put the light on).
http://www.sonymobile.com/gb/products/accessories/charging-dock-dk26/
Click to expand...
Click to collapse
Price is supposed to be ~35£. Could be cheaper, but it's not that bad.
So I was using my phone and was running low on battery power. My ended up dying at like 5% as usual with my droid turbo. I was with my friend in his girlfriends car and plugged it into her cheap charger she picked up at a gas station or something. My phone registered the charger and then began the battery symbol like usual although it never got to the battery percentage, it just stayed as a gray battery symbol with the lightning bolt. After a while the phone screen went black and wouldn't respond to anything and figured that the charger just made the phone go dead and that I could plug it into a Verizon charger to make it work again. When I got home I plugged it in and nothing, no response at all not even the green light at the top of the phone. I plugged it into my computer and it shows up on device manager as QHSUSB_BULK. Now to be clear my phone was never rooted or had anything done to it. The phone was completely stock. I need help frantically because I need to get some media off of the phone if at all possible, whatever the cost. Not sure if just letting it charge for a while will help or not. Thanks for the help in advance.
If you plug it into your home charger it should turn on at least and show the battery symbol when charging and it should go up if you haven't tried it already. If it doesn't, sounds like some kind of charging issue.
BlueForce64 said:
If you plug it into your home charger it should turn on at least and show the battery symbol when charging and it should go up if you haven't tried it already. If it doesn't, sounds like some kind of charging issue.
Click to expand...
Click to collapse
The phone doesnt respond at all to any commands. The green light doesn't even pop up as if thebphone was clear dead. Took it to Verizon they thought the battery might be fried which I guess would keep the phone from turning on.
That is entirely possible. When I buy after market chargers, I generally only buy anker stuff. I've never had a problem with their stuff. Get what you pay for. Not that you bought that but yeah.
BlueForce64 said:
That is entirely possible. When I buy after market chargers, I generally only buy anker stuff. I've never had a problem with their stuff. Get what you pay for. Not that you bought that but yeah.
Click to expand...
Click to collapse
Yeah I definitely learned a lesson. Is there any way I can get the data off of it though? Would Motorola recover the data for me or is there some way? The data should all still be there considering there were no deletion processes. Of course maybe im wrong but I just hope I can get everything recovered.
It's possible if it will connect to your computer and you can read it but otherwise I'm not sure
Assuming the charging port is damaged you could try a wireless charger.
Sent from my XT1254 using Tapatalk
Well like I said the computer can read it, but thats all it can do. It recognizes it as being plugged in but cant do anything else.
dnwhome3 said:
Assuming the charging port is damaged you could try a wireless charger.
Sent from my XT1254 using Tapatalk
Click to expand...
Click to collapse
Tyler2265 said:
Well like I said the computer can read it, but thats all it can do. It recognizes it as being plugged in but cant do anything else.
Click to expand...
Click to collapse
If you try a Qi wireless charger, that would give it the chance to actually charge. Maybe some circuitry in the USB port is damaged and it's not receiving a charge. You actually have the phone, so you know better. But wouldn't hurt to go to a store and try putting it on a Qi charger for a few minutes as a test. When my phone is OFF and I put it on a Qi charger, it actually turns it on, boots the phone.
That is definitely a thing to try. If your computer can read it then you can easily save the files off the phone.
I'll have to give that QI a try. People st Verizon probably didn't even think of that.
How would I go about getting the data off of it though? The phone doesnt show up on computer just shows up in device manager under the code I wrote in the first post.
Tyler2265 said:
I'll have to give that QI a try. People st Verizon probably didn't even think of that.
How would I go about getting the data off of it though? The phone doesnt show up on computer just shows up in device manager under the code I wrote in the first post.
Click to expand...
Click to collapse
One step at a time. If it will charge normally with Qi and boot, then it once booted it might show up as device on PC.
BlueForce64 said:
That is definitely a thing to try. If your computer can read it then you can easily save the files off the phone.
Click to expand...
Click to collapse
I tried the QI charger and it did not work. Thr light on the Verizon pad flashed red. Thr battery has got to be fried. So im not exactly sure what to do next.
Well, you can always get a new one through insurance or through swappa. I get that it's the stuff you want to save though. Might not be able to if your computer can't see it as a SD card unfortunately.
BlueForce64 said:
Well, you can always get a new one through insurance or through swappa. I get that it's the stuff you want to save though. Might not be able to if your computer can't see it as a SD card unfortunately.
Click to expand...
Click to collapse
Well the way I look at it there's always other phones but not memories. So if worse comes to worse I'll just tear the phone apart and find the internal storage.
Tyler2265 said:
I tried the QI charger and it did not work. Thr light on the Verizon pad flashed red. Thr battery has got to be fried. So im not exactly sure what to do next.
Click to expand...
Click to collapse
Tyler2265 said:
Well the way I look at it there's always other phones but not memories. So if worse comes to worse I'll just tear the phone apart and find the internal storage.
Click to expand...
Click to collapse
Very sorry you couldn't resuscitate your phone. Hope you can save your data.
ChazzMatt said:
Very sorry you couldn't resuscitate your phone. Hope you can save your data.
Click to expand...
Click to collapse
So there's no way you guys can think of to get this data off? I could use all the help I can get
Even if you tore yours apart and found the memory chip, it's soldered onto the board. I know because I've opened my turbo to do repairs and it's not hard but not easy. Maybe, just maybe, if you had the sophisticated equipment you could apply the proper voltage to be able to read the card, assuming you could find the + and - pins on it and then also the transmit pins on it and solder yourself a usb cable to direct connect to it to the computer, that might work but would be extremely complicated. I'm a professional electronics technician and I test, build, and repair boards but not phones. I do surface mount work though. Anyways, got off topic. So unless you got that going for you, I don't see it happening.
One last thought, do you have Motorola drivers installed on your PC? Could help. Don't know.
Tyler2265 said:
So there's no way you guys can think of to get this data off? I could use all the help I can get
Click to expand...
Click to collapse
There are youtube guides out there on how to replace the battery in this phone. It's not easy, but it's probably easier than finding the storage chip and figuring out a way to build a new physical interface to access it. New battery = resurrected phone = get your data back. Maybe.
https://youtu.be/VHFkTgjWzOo
Yeah that's also probably a lot easier than all that. The battery isn't too hard to replace. I totally over thought that.