I've a i9000 and i9300 which I don't really use so I thought I'd do some updating.
A while back I put CM11 on the i9000, and put it on the i9300 yesterday, then I thought I'd root them, that's when the problems started!
Booted into download mode and used Odin to put the firmware on, it reports successful but the phone doesn't boot past the first screen.
I used the CF-Root file -XX_OXA_JVT-v4.3-CWM3RFS.tar but I've also tried JVR, JVS, JVU, JVZ and JW4 out of desperation....with the same results.
I'm glad I started with the i9000, and I'd like to try to recover it, but I'm at a loss now :crying:
That CF kernel is for stock JVT. Hopefully you didn't try it for CM11?
It would last to flash a full firmware, reboot once, and after that you can flash compatible custom kernel (same image contains also custom recovery).
We have quite good sticky threads in this section that can guide you. Which Odin version did you use? 1.83 and 1.82 are the last ones with full compactibility for the i9000.
tetakpatalked from Nexus 7 flo
tetakpatak said:
That CF kernel is for JVT. We have quite good sticky threads in this section that can guide you. Which Odin version did you use? 1.83 and 1.82 are the last ones with full compactibility for the i9000.
tetakpatalked from Nexus 7 flo
Click to expand...
Click to collapse
Ah! I was using V3! And yes I tried it with CM11!
I found this post and have got it back, now to try again!!
eusty said:
Ah! I was using V3! And yes I tried it with CM11!
I found this post and have got it back, now to try again!!
Click to expand...
Click to collapse
But I'm unable to install a ROM!
Recovering the phone as above also puts ClockworkMod on, but it fails to install the ROM with file signature errors, trying both the CM and Gapps gives the same error.
Also trying to install ClockworkMod using heimdall as I did previously also give an error
Code:
Session begun.
Downloading device's PIT file...
PIT file download successful.
ERROR: Partition "kernel" does not exist in the specified PIT.
Ending session...
Releasing device interface...
All I want is CMmod back on again!
After quite a few attempts at different ways and a few 'black screens of death' I've managed to get it completely back to stock using heimdall following this. My head is spinning!
Now I've just got to start with CWmod and CMmod again. Now it's stock I'm tempted to try and root it.....but that was the start of the problems last time!
After trying to root again and another bricking I decided to give up with the root!
The issue is when trying to install CWmod I get the same error as in post #4, which means I'm completely lost now as the phone was back to stock.
[email protected] Ok coming from a Windows background I forget about case, and the CMmod wiki is incorrect. The issue is as I've had my head spinning so much I forgot I did this last time!
eusty said:
After trying to root again and another bricking I decided to give up with the root!
The issue is when trying to install CWmod I get the same error as in post #4, which means I'm completely lost now as the phone was back to stock.
Click to expand...
Click to collapse
EDIT: Ok coming from a Windows background I forget about case, and the CMmod wiki is incorrect. The issue is as I've had my head spinning so much I forgot I did this last time!
EDIT AGAIN: Now it doesn't boot again!
eusty said:
But I'm unable to install a ROM!
Recovering the phone as above also puts ClockworkMod on, but it fails to install the ROM with file signature errors, trying both the CM and Gapps gives the same error.
Also trying to install ClockworkMod using heimdall as I did previously also give an error
Code:
Session begun.
Downloading device's PIT file...
PIT file download successful.
ERROR: Partition "kernel" does not exist in the specified PIT.
Ending session...
Releasing device interface...
All I want is CMmod back on again!
Click to expand...
Click to collapse
This was totally wrong way to install. Who adviced you to flash CyanogenMod with Heimdall? Are you not reading install instructions at all?
I adviced you yesterday to go with sticky threads here.
tetakpatalked from Nexus 7 flo
tetakpatak said:
This is totally wrong. Who told you to flash CyanogenMod with Heimdall? Are you not reading install instructions at all?
tetakpatalked from Nexus 7 flo
Click to expand...
Click to collapse
I'm not! I'm trying to install ClockworkMod using heimdall, I install Cyanogen from the SD after entering recovery mode.
http://wiki.cyanogenmod.org/w/Install_CM_for_galaxysmtd
eusty said:
I'm not! I'm trying to install ClockworkMod using heimdall, I install Cyanogen from the SD after entering recovery mode.
http://wiki.cyanogenmod.org/w/Install_CM_for_galaxysmtd
Click to expand...
Click to collapse
You have to flash a stock firmware and after that compatible kernel for it, as kernel and recovery share the same image on the i9000. So unlike other devices, the recovery can not be flashed separately. That's why the kernel must be compatible with the ROM.
If you have flashed once ROM based on Android 4.3 or higher, your partitions sizes have been modified and you must flash also PIT file together with stock firmware and enable re-partition.
tetakpatalked from Nexus 7 flo
Yes I've also flashed the PIT, I used the instructions from http://forum.xda-developers.com/showthread.php?t=1196179
which included it.
I will try to recover it using the sticky at the top of the forum then try CWmod again.
Thanks for the help [emoji3]
Sent Using Tapatalk
eusty said:
Yes I've also flashed the PIT, I used the instructions from http://forum.xda-developers.com/showthread.php?t=1196179
which included it.
I will try to recover it using the sticky at the top of the forum then try CWmod again.
Thanks for the help [emoji3]
Sent Using Tapatalk
Click to expand...
Click to collapse
If you're using Heimdall, be sure to use v1.31 as the later versions aren't working so good on the i9000 anymore.
Do you use Linux or Windows as your PC's OS?
tetakpatalked from N7100
I'll grab an older version of Heimdall as I think I downloaded the latest.
I'm using Windows (7 64 bit).... along with it's USB driver idiosyncrasies
Sent Using Tapatalk
I restored the phone to stock from your instructions at the top of the forum, then tried a rooted ROM.
Everything went fine, although I'm not sure if I had root access (as it worked I didn't bother to check). Then I tried CWmod but it still failed to install, so went back to stock again.....it still wouldn't install
From the ClockworkMOD website..
Download recovery -- you can directly download a recovery image using the link below, or visit clockworkmod.com/rommanager to check for the latest version of ClockworkMod recovery for your device (if your device can be found there).
Recovery: Semaphore_2.7.4.tar
Click to expand...
Click to collapse
If you use their link (me being lazy did) then it fails, but go to the website and find the image then it works!! It's a slightly different filesize, so maybe a different version?
The ironic thing it that on the CyanogenMOD site it mentions that the phone hasn't got to be rooted to install it, but what I didn't realise was CyanogenMOD it also installs a different firmware...which is rooted!!
At least through all this I'm a bit wiser as to flashing the phone etc :good:
@eusty Rom Manager app is useless for i9000, except for reading the names of nandroid backups.
tetakpatalked from N7100
Related
I was going through the below tutorial everything seem to go find until i restarted. Then it froze and has been frozen for a while im trying to wait an hour its been about 20 minutes.
Any thoughts ideas on where to start to get my device rolling or is it done for. thanks for any device you can provide.
the unlockr .com/
2010/11/29/how-to-flash-a-custom-recovery-image-on-the-samsung-galaxy-tab]
did you use CWM from Rom Manager?
This is NOT optimized for the SGT.. nor is it encouraged.
Anyhow, have you tried to check if your computer can detect your tab, through Kies or Odin?
Sef_P1000 said:
did you use CWM from Rom Manager?
This is NOT optimized for the SGT.. nor is it encouraged.
Anyhow, have you tried to check if your computer can detect your tab, through Kies or Odin?
Click to expand...
Click to collapse
Yes I did use CWM from Rom Manager
Kies says connecting but doesn't ever connect
Odin3 says 0:[COM6]
so what can I do?
what you can do , is go grab the stock gingerbread and flash it via odin and then take the root file and u'll have both gingerbread and also the cwm ...
follow chainfire steps and u'll do it in 4mins
k0sh said:
what you can do , is go grab the stock gingerbread and flash it via odin and then take the root file and u'll have both gingerbread and also the cwm ...
follow chainfire steps and u'll do it in 4mins
Click to expand...
Click to collapse
t
What do you mean do you have instructions somewhere? please post thanks for your help
iamahero said:
t
What do you mean do you have instructions somewhere? please post thanks for your help
Click to expand...
Click to collapse
he was pertaining to this thread..
http://forum.xda-developers.com/showthread.php?t=1073854
noxxious said:
he was pertaining to this thread..
http://forum.xda-developers.com/showthread.php?t=1073854
Click to expand...
Click to collapse
You the dude
Sent From (I'm In Luv With My Tab)
similar problem....also stuck on boot
but I got there a different way. (FIXED)
Let me start off by saying I am stupid I have a tmobile tab and it was running awesome on overcome 2.0.0 rc1 with ext4 conversion and OC kernel and then I saw the honeycomb alpha had been released for cdma, which of course I dont have (gsm), and decided to try the rom with the oc gsm kernel, which didnt work.
then I dun goofed. Instead of going back to overcome in cwm, I flashed the damn experimental honeycomb package again, kernel and all and then loaded the tab.....dumb...weird colors and then nothing....screen just goes black and no matter what I cannot see cwm screen. And now odin no longer recognizes the tab.
heimdall works and I flashed back kernal from :[OC/UV][7th Jun][Kernel] koxudaxi kernel [GSM][2.2&2.3][KernelPatch]
which gives me cwm, but it keeps giving me an error that i cant mount sd card
I have tried flashing the safe gingerbread stock with pit file (still stuck on boot logo)
then tried flashing rotostock tmobile rom ( but no pit file and when it boots it still shows the gingerbread bootlogo)....do i flash with P1_add_hidden.pit added?
Any and all help will be much appreciated. please don't be too mean. I know i shouldn't have done what i did
[UPDATE]
So I figured it out. I reinstalled samsung usb driver from within odin folder, and odin suddenly started working. went back to stock GB and then on to Overcome 2.0.0 Gold w/ ext4 and oc'd to 1.4
I had to reinstall the hiemdall driver too after reinstalling samsung driver, but now they both work again....... so stoked
Hello,
I have a problem where with downgrading, it just bricks my phone. Can somebody step-by-step (and maybe help with links) post how to fix my phone? I'm considering just getting an iPhone now... I'm mostly fed-up with Android.
Captivate sig link/ Mikes safe kf1/ 3 file odin
^Go on the link that he posted. And dude don't get an Iphone, you're going to regret it! Trust me!
U have to do a two step flash. Flash a miui/cm7 rom..then get back to recovery using three button combo and flash rhe miui/cm7 rom
Sent from my I897 in the LION filled territory called Kenya using XDA App
Second problem,
I tried to do a flash of the newest Cyanogen update (7.10) from the stock Odin, which worked quite well, and it didn't complete. Odin then decided to crash. After that, my phone is now stuck in "Firmware Upgrade Fail! Try using recovery mode". I can't get into Download mode, and I can't get into recovery mode. Any ideas?
I saw on the Rogers website that an iPhone 4 (8gb) is $0 on a 3 year contract
Use that screen as dl mode.
mrhaley30705 said:
Use that screen as dl mode.
Click to expand...
Click to collapse
Tried that, and it didn't show up in Odin...
EDIT: When I try to use Heimdall, it says that it passes in the Heimdall frontend, but when I look at my phone on the screen, the progress bar never finishes. It just stops at about 90% (estimated)...
If you've installed Heimdall drivers, you will need reinstall Samsung drivers to get Odin to work.
mrhaley30705 said:
If you've installed Heimdall drivers, you will need reinstall Samsung drivers to get Odin to work.
Click to expand...
Click to collapse
Thanks! I'll try that as soon as it finishes installing. What would the way to install the new Cyanogen mod without bricking my phone be?
After flashing to stock, follow the install instructions in the first post of the CM thread. If you have questions about the installation, ask in the q&a thread for that rom (it's stickied in the q&a sub forum)
Downgrade to android 3.0 or 3.2
I have the same issue but i'm using samsung glaxy tab 10.1 and i want to downgrade to android 3.0 or 3.2, i'm on android 4.0.3 ICS, i used CM9 to root my tablet. I would be very thankful with any help!!
Hello,
I will start with saying that Ive already checked every tutorial in every android website.
here is what I did.
I had Miui (Not the ICS one) I have tried to flash CM9 with the existing recovery. than something somewhere on the flash procedure go wrong and the phone just rebooted and putted in loop with no recovery option but download option. so I tried to flash the stock rom using odin 1.85, and the phone just looping on the image of the mobile operator. I did this procedure with the odin for more stock roms I found.
thanks in advance really I need your help...
http://www.theandroidsoul.com/xxjvu/
maybe you forget ‘Re-Partition’checkbox, it's important.
Hmmm.. perhaps, you have to make sure all the files are properly placed (depending on the ROM you are installing). Also, I'd recommend using a pit file (and don't forget to click on "Re-Partition".. So far, it worked for me. ^.~
Hi all,
i bought a galaxy tab last month, and i installed cyanogenmod 9 nightlies. i was using without problem. but after 23.07 nightlies i got play store error. it wouldnt open. i saw that google account was removed. than i wanted full factory reset and wipe sd card and than clean cyanogenmod install...
Off course clockwork recoverymod was also deleted (i know i am stupid!)
Than i found some p1000 stock roms and tried install with odin. And i did it, installed rom without problem but when i turn my tablet on its waiting on boot screen. it doesnt turn on. stays on boot.
I found this when i was on recovery mod (tablets stock recovery) SEE ATTACHMENT PLEASE.
Now i have a tablet and i cant do anything. I think if i have a 3 files stock rom i can flash it with odin.
Do you know what do i have to do now? Please help me guys
You have gone this far for nothing.
No Play or Gmail means you just need to flash gapps.
I know people say nightlies no need to flash gapps.
But if gapps is missing, just flash gapps again.
Now you are at this stage,
use Overcome method:
Go to overcome site
Http://www.teamovercome.net
Read the guide,
Missing pictures can be seen here.
http://forum.xda-developers.com/showthread.php?p=20974872
Follow the picture step by step.
Basically to restock:
Download GB-stock-safe-v5.zip, unzip it and and flash with ODIN according to the guide.
Once done, continue to flash overcome kernel tar using Odin
and then boot to CWM recovery and flash CM9 twice
then flash gapps.
Hopefully that solve your problem.
yes, i found it here in xda, and it worked. but thanks for your reply, if someone has same problem they can read your message. it works
erhangulsum said:
yes, i found it here in xda, and it worked. but thanks for your reply, if someone has same problem they can read your message. it works
Click to expand...
Click to collapse
priyana said:
You have gone this far for nothing.
No Play or Gmail means you just need to flash gapps.
I know people say nightlies no need to flash gapps.
But if gapps is missing, just flash gapps again.
Now you are at this stage,
use Overcome method:
Go to overcome site
Http://www.teamovercome.net
Read the guide,
Missing pictures can be seen here.
http://forum.xda-developers.com/showthread.php?p=20974872
Follow the picture step by step.
Basically to restock:
Download GB-stock-safe-v5.zip, unzip it and and flash with ODIN according to the guide.
Once done, continue to flash overcome kernel tar using Odin
and then boot to CWM recovery and flash CM9 twice
then flash gapps.
Hopefully that solve your problem.
Click to expand...
Click to collapse
erhangulsum said:
Hi all,
i bought a galaxy tab last month, and i installed cyanogenmod 9 nightlies. i was using without problem. but after 23.07 nightlies i got play store error. it wouldnt open. i saw that google account was removed. than i wanted full factory reset and wipe sd card and than clean cyanogenmod install...
Off course clockwork recoverymod was also deleted (i know i am stupid!)
Than i found some p1000 stock roms and tried install with odin. And i did it, installed rom without problem but when i turn my tablet on its waiting on boot screen. it doesnt turn on. stays on boot.
I found this when i was on recovery mod (tablets stock recovery) SEE ATTACHMENT PLEASE.
Now i have a tablet and i cant do anything. I think if i have a 3 files stock rom i can flash it with odin.
Do you know what do i have to do now? Please help me guys
Click to expand...
Click to collapse
I have the same problem, but I have the P1000N and the overcome is not compatible. I am on stock GB with superoneclick root. Any suggestions?
You can restock using GB stock safe v5 once, then flash your N stock GB again.
Or if your stock has pit file, you don't need GB stock safe v5.
Sent from my GT-P1000 using xda app-developers app
priyana said:
You can restock using GB stock safe v5 once, then flash your N stock GB again.
Or if your stock has pit file, you don't need GB stock safe v5.
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
I restocked with Froyo that has pit, then flashed GB. Not sure if GB had pit though. Does it matter or should I flash stock safe v5 anyway first ?
priyana said:
You can restock using GB stock safe v5 once, then flash your N stock GB again.
Or if your stock has pit file, you don't need GB stock safe v5.
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
Thanks priyana.
Could you please post the steps as I am afraid to hard brick my tab again.
If you follow my signature, that will take you to overcome files.
The PDF guide is quite clear.
Anyway it doesn't need to be GB. You want pit file so Odin can repartition the storage.
There is a chance your internal chip is failing.
Sent from my GT-P1000 using xda app-developers app
I don't need to worry that the Overcome will brick my tab? Everything i have found says it will, or am I missing something?
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
well, I don't know for sure.
But the P1000N/L has different touch screen driver in their kernel.
You can flash it using Odin and you can even use the recovery, since CWM isn't touch screen based.
But that is not what I am saying above.
You asked for guide, I said Overcome guide is clear.
Have you even download the PDF and read?
Page 7/8 has picture of what to put in Odin fields. You can put GB stock safe v4, v5, or whatever, a Panama or Trinidad based GB, or even Froyo, the picture is still going to be the same (or similar).
So, use your froyo, use the guide. (or not) up to you.
priyana said:
well, I don't know for sure.
But the P1000N/L has different touch screen driver in their kernel.
You can flash it using Odin and you can even use the recovery, since CWM isn't touch screen based.
But that is not what I am saying above.
You asked for guide, I said Overcome guide is clear.
Have you even download the PDF and read?
Page 7/8 has picture of what to put in Odin fields. You can put GB stock safe v4, v5, or whatever, a Panama or Trinidad based GB, or even Froyo, the picture is still going to be the same (or similar).
So, use your froyo, use the guide. (or not) up to you.
Click to expand...
Click to collapse
Ok I will try it. Thank you very much!
This error regularly happens when flashing stock ROMs. Then you will have to download and flash dbdata.tar as PDA in Odin (Google "P1000 dbdata.tar"; it's about 1.25MB or so). This solves it for me and a few others.
geno93n0 said:
This error regularly happens when flashing stock ROMs. Then you will have to download and flash dbdata.tar as PDA in Odin (Google "P1000 dbdata.tar"; it's about 1.25MB or so). This solves it for me and a few others.
Click to expand...
Click to collapse
Did that twice. Didn't help
scorpionhd2 said:
Did that twice. Didn't help
Click to expand...
Click to collapse
I just restocked less than an hour ago and ran into the same thing. Are you using the right PIT for your model?
geno93n0 said:
I just restocked less than an hour ago and ran into the same thing. Are you using the right PIT for your model?
Click to expand...
Click to collapse
I assume so. I got it from HumberOS (i think). I will double check later as I am at work right now. I wouldn't mind it if you could post it if you have it.
geno93n0 said:
I just restocked less than an hour ago and ran into the same thing. Are you using the right PIT for your model?
Click to expand...
Click to collapse
OK so I am using the correct PIT, or so I understand. I even tried reflashing the dbdata.tar as PDA in Odin. Still no change.
Could this have an affect on the modem of the tab as well and cause it not to read the sim?
scorpionhd2 said:
OK so I am using the correct PIT, or so I understand. I even tried reflashing the dbdata.tar as PDA in Odin. Still no change.
Could this have an affect on the modem of the tab as well and cause it not to read the sim?
Click to expand...
Click to collapse
No clue, never had to reflash my modem. That may have introduced a wild variable into the equation, because usually the dbdata trick fixes that problem.
I advise starting the whole Overcome restock process from the beginning. Try to ignore the modem part.
YAY! Fully rooted with SU and BusyBox Installed. I restocked to Froyo with PIT and Re-partition, then reflashed Froyo again (no PIT). Then flashed the dbdata.rfs.tar file. Then I was able to use Superoneclick to root and install SU & BB.
Thanks to each one of you for your help!
Deleted
I tried upgrading my international N7000 to CM10.3 following the instructions in
http://wiki.cyanogenmod.org/w/Install_CM_for_n7000
but now the phone won't even boot into the recovery, all it shows is
Samsung
GALAXY Note
GT-N7000
/ \
/ | \
/--*-\
When i tried flashin from my Mac iusing Heimdall,
the download finished on the mac, but on the N7000
it still showed the blue line etc. I waited a lng time and tried
rebooting, but got the above.
Re-flashing in Heimdall had no effect.
I then tried flashing
hardcore-speedmod-ics-recovery-n7000.tar
using Odin 3.185 from my VMwars Fusion XP install,
and that seemed to finish ok, but no luck either.
I looked for the latest CWM 6.0.4.3 recovery, but I cannot find any
odin-flashable format for it, and of course I cannot use the sdcard
as I cannot even boot into any recovery as is.
Can anyone suggest next steps?
sejtam said:
I tried upgrading my international N7000 to CM10.3 following the instructions in
http://wiki.cyanogenmod.org/w/Install_CM_for_n7000
but now the phone won't even boot into the recovery, all it shows is
Samsung
GALAXY Note
GT-N7000
/ \
/ | \
/--*-\
When i tried flashin from my Mac iusing Heimdall,
the download finished on the mac, but on the N7000
it still showed the blue line etc. I waited a lng time and tried
rebooting, but got the above.
Re-flashing in Heimdall had no effect.
I then tried flashing
hardcore-speedmod-ics-recovery-n7000.tar
using Odin 3.185 from my VMwars Fusion XP install,
and that seemed to finish ok, but no luck either.
I looked for the latest CWM 6.0.4.3 recovery, but I cannot find any
odin-flashable format for it, and of course I cannot use the sdcard
as I cannot even boot into any recovery as is.
Can anyone suggest next steps?
Click to expand...
Click to collapse
1st things 1st. Why would u use heimdall or odin? And what is your current ROM before trying to flash CM 10.3, was it stock? You should have looked for CWM recovery or Philz safe kernels as base when doing ROM flashing ESPECIALLY custom roms. From what you said, then can you still boot into download mode? I have no knowledge of heimdall so just download Stock Firmware, flash it with odin and see if you can boot your N7000 first.
The worst case scenarios is you are experiencing emmc bug-brick. go to the thread and read carefully to deduce your type of 'brick' and find solutions there. Good Luck.
I was on a stock 4.0.4 (but rooted). I originally tried flashing the cwm from the sd card, but after starting to load it it also just hung,
so I looked for an alternative..
I found a post on stockroms (http://forum.xda-developers.com/showthread.php?t=1424997) but the links all point to hotfile.com. which my browser says it cannot find. is hotfile dead? Is there an alternative?
sejtam said:
I was on a stock 4.0.4 (but rooted). I originally tried flashing the cwm from the sd card, but after starting to load it it also just hung,
so I looked for an alternative..
I found a post on stockroms (http://forum.xda-developers.com/showthread.php?t=1424997) but the links all point to hotfile.com. which my browser says it cannot find. is hotfile dead? Is there an alternative?
Click to expand...
Click to collapse
Go to sammymobile.com if I'm not wrong. Download the stock firmware there. Rooted but do u have cwm installed? Rooted doesn't mean you have cwm installed.
Sent from my GT-N7000 using XDA Free mobile app
same problem
Jackwu696 said:
Go to sammymobile.com if I'm not wrong. Download the stock firmware there. Rooted but do u have cwm installed? Rooted doesn't mean you have cwm installed.
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
i have the same problem , only mine loads into the recovery menu , ive tried finding a working odin to nstall it back to factory.
when i had this problem last night , i wasnt sure what i done but i managed to install a custom rom and that worked but now i seem to be getting status 7 error ,
my computer wont recognise my phone so i cant do anything that way . any ideas or links to solutions will be appreciated
i have the same problem
conanbrapp said:
i have the same problem , only mine loads into the recovery menu , ive tried finding a working odin to nstall it back to factory.
when i had this problem last night , i wasnt sure what i done but i managed to install a custom rom and that worked but now i seem to be getting status 7 error ,
my computer wont recognise my phone so i cant do anything that way . any ideas or links to solutions will be appreciated
Click to expand...
Click to collapse
I'm sorry so did u succeed or did you not succeed in installing the custom rom? If your custom rom boots fine then all u need is to search for solving status 7 error thread. My advice to all noobs is to always try n avoid installimg anything except stock rom in odin. Always read and re read before flashing anything that's beyond your knowledge. Basic knowledge of flashing cusroms is :
1. ALWAYS make sure you're on SAFE and COMPATIBLE KERNEL. Most rom threads ALWAYS Include threads/links to a specific recovery/kernel to use. Read n RE READ that.
2. Wipe everything IN RECOVERY mode before flashing a rom.
Sent from my GT-N7000 using XDA Free mobile app
fixed miine
Jackwu696 said:
Go to sammymobile.com if I'm not wrong. Download the stock firmware there. Rooted but do u have cwm installed? Rooted doesn't mean you have cwm installed.
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
Jackwu696 said:
I'm sorry so did u succeed or did you not succeed in installing the custom rom? If your custom rom boots fine then all u need is to search for solving status 7 error thread. My advice to all noobs is to always try n avoid installimg anything except stock rom in odin. Always read and re read before flashing anything that's beyond your knowledge. Basic knowledge of flashing cusroms is :
1. ALWAYS make sure you're on SAFE and COMPATIBLE KERNEL. Most rom threads ALWAYS Include threads/links to a specific recovery/kernel to use. Read n RE READ that.
2. Wipe everything IN RECOVERY mode before flashing a rom.
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
im not Sure what i did , i unbricked (soft) and successfully installed kitkat not sure exactly how but it worked.... still have root too ... had and error about needing to wipe data for suib i think but thats the only fallback i fell into
conanbrapp said:
im not Sure what i did , i unbricked (soft) and successfully installed kitkat not sure exactly how but it worked.... still have root too ... had and error about needing to wipe data for suib i think but thats the only fallback i fell into
Click to expand...
Click to collapse
If you're able to boot up properly n prompted to wipe, then do it. But do it in recovery not on device.
Ok, I downloaded one of the stock kernels for my internatinal N7000, but flashing that with Odin 3.185 hangs about 3/4 through (has now been
sitting there for >60 mins).
Looks like I am screwed?
The file I found is KIES_HOME_N7000XXLT4_N7000OXALT4_1103517_REV02_user_low_ship.tar.md5
I f I wanted to try flashing this with Heimdall, I'd need to know partition numbers I think
Where can I get those?
Or should I get another file?
sejtam said:
Ok, I downloaded one of the stock kernels for my internatinal N7000, but flashing that with Odin 3.185 hangs about 3/4 through (has now been
sitting there for >60 mins).
Looks like I am screwed?
The file I found is KIES_HOME_N7000XXLT4_N7000OXALT4_1103517_REV02_user_low_ship.tar.md5
I f I wanted to try flashing this with Heimdall, I'd need to know partition numbers I think
Where can I get those?
Or should I get another file?
Click to expand...
Click to collapse
Before that, do u have KIES installed? KIES is NOT compatible with odin and will cause potential trouble. So is some firewall and antivirus apps. You need to disable all of them before using odin. Please search the thread http://www.sammobile.com/firmwares/ for stock rom site.
Sent from my GT-N7000 using XDA Free mobile app
Ok. I downloaded two stock roms from sammobile:
[email protected] 1 mathias staff 808649674 May 9 10:53 N7000XXLT5_N7000MBCLT1_MBC.zip
[email protected] 1 mathias staff 750466356 May 9 10:50 N7000XXLRL_N7000OXELR5_MBC.zip
but both fail with some (unreadable, apparently character set issue) error under ODIN.
I found this:
http://droidangel.blogspot.sg/2012/01/samsung-galaxy-note-gt-n7000-all.html
which shows how to do a full flash , including PIT file, but the links again go to hotfile which seems to be down.
http://hotfile.com/dl/140099962/b9e0d63/Q1-20110914_16GB.pit.rar.html
Where can I get a) separate
CODE_N7000xxxxx_CLxxxxxxx_REVxx_user_low_ship.tar.md5
MODEM_N7000xxxxxx_REV_00_CLxxxxxx.tar.md5
GT-N7000-CSC-MULTI-xxxxxx.tar.md5
and the PIT file?
sejtam said:
Ok. I downloaded two stock roms from sammobile:
[email protected] 1 mathias staff 808649674 May 9 10:53 N7000XXLT5_N7000MBCLT1_MBC.zip
[email protected] 1 mathias staff 750466356 May 9 10:50 N7000XXLRL_N7000OXELR5_MBC.zip
but both fail with some (unreadable, apparently character set issue) error under ODIN.
I found this:
http://droidangel.blogspot.sg/2012/01/samsung-galaxy-note-gt-n7000-all.html
which shows how to do a full flash , including PIT file, but the links again go to hotfile which seems to be down.
http://hotfile.com/dl/140099962/b9e0d63/Q1-20110914_16GB.pit.rar.html
Where can I get a) separate
CODE_N7000xxxxx_CLxxxxxxx_REVxx_user_low_ship.tar.md5
MODEM_N7000xxxxxx_REV_00_CLxxxxxx.tar.md5
GT-N7000-CSC-MULTI-xxxxxx.tar.md5
and the PIT file?
Click to expand...
Click to collapse
Of course you fail... When using ODIN, U should have downloaded the .tar. if you downloaded a zip. then unzip it first to get the tar file, then you flash it with odin. All requests are included in the stock.tar And PLEASE DO NOT Play with PIT files if you don't know what you are doing.
So now what you need to do is. :
1. DISABLE KIES (Uninstall it better), Your firewall, antivirus.
2. Install CORRECT Samsung USB driver. (Search keyword "download samsung N7000 usb drivers")
3. Unzip your zip file and extract the tar.file.
4. Run ODIN as Administrator (Right click/run as)
5. Go to download mode. connect your device to Pc/laptop.
6. Wait until Odin detects your device, click AP/PDA and choose the tar file you extracted.
7. DO NOT tick partition.
8. Let it run
Of course I unzipped the zip to get a SINGLE .tar.md5, but flashing that fails on factoryfs about 3/4 through. consistently.
sejtam said:
Of course I unzipped the zip to get a SINGLE .tar.md5, but flashing that fails on factoryfs about 3/4 through. consistently.
Click to expand...
Click to collapse
Try updating your odin. Use the newest vers. And try and read this https://www.google.com/url?q=http:/...ds-cse&usg=AFQjCNGd2e3iG5hkDeo0KyAjGuCSfQSLUw . If All fails then it's a confirmed SUPER-BRICK and there's nothing except samsung service centre can help you now... Sorry for not being able to help more..
Thanks. That led me to
http://forum.xda-developers.com/showthread.php?t=1656635
where I found the PIT file, but for ROMs pointed to http://forum.xda-developers.com/showthread.php?t=1530501
which again points to hotfile and fileserve.com , which (besides being under maintenance) says
FileServe can only be used to download and retrieve files that you have uploaded personally.
which makes it useless for finding ROMs...
sejtam said:
Thanks. That led me to
http://forum.xda-developers.com/showthread.php?t=1656635
where I found the PIT file, but for ROMs pointed to http://forum.xda-developers.com/showthread.php?t=1530501
which again points to hotfile and fileserve.com , which (besides being under maintenance) says
FileServe can only be used to download and retrieve files that you have uploaded personally.
which makes it useless for finding ROMs...
Click to expand...
Click to collapse
His link to ROMS were basically the same ones you can download at sammobile.