Database Develop

DIY GUIDE TO REPLACING THE 19$ BROKEN GLASS on the galaxy note

hi folks. i managed to replace my galaxy note front glass with a new one i got from ebay for 19$ and i want to make a step by step guide on how it can be done.
i did it using common tools and a s load of pacience and attention.
the tools i used are: heat gun with hi and low settings, exacto knife set,small phillips and flat screwdrivers, goo gone, and optional a screen protector.
first take the phone apart as it's describet in countless of threads and youtube videos. you should end up with the screen assembly shown in the first picture.
now we have to separate the glassscreen from the frame it sits on. for this we fire up the heat gun.
a few words about using the heat gun.
-my gun had 2 settings: low and high. during all this process i used it on low.
-don't put the gun directly and/or close to the thinn plastic wires that hold the two connectors.
- dont hold the gun in the same place more than 3 seconds, instead swipe the gun around the spot and the screen like u would do with a paint brush when painting.
- dont hold the gun too close, that is closer than 3 inch
-concentrate on the spot u working at but try to heat up the whole screen assembly, as it has to give away from all the points kind of at the same time, and not just the point u working at.
- dont overheat the screen as this will damage the amoled. thats how i got the two yellow spots on my screen. first one by accident and second one intentionaly to see if indeed the overheating is what caused it.
A very good rule for this is dont heat the phone more than you can bear to touch it cause afterall you have to hold the phone while working on it...
the way i did it is :
-i heated up the whole screen assembly, back and front, for a minute or two
- than i started to stick the tip of the exacto knife between the glass and the metal edge that sorrounds it. i started from the upper right corner, the side where the front camera is. see photo 2.
the goal is to unstick the glass from the frame. in photo 3 the frame and the screen is shown without the upper glass. this photo was taken after i finished everything, thats why the screen can be seen inside the frame. but i posted it to show the black sticky tape that its used to hold the glass to the frame. i think is the same kind of sticky tape thats used in all the touchphones including iphone to hold the front glass to the rest of the phone. in photo 4 i unsticked some of the tape to show it better. this tape is the main thing that holds the the glass to the frame. the other thing that hold the screen to the frame is some sticky glue on the back of the screen. but this is much softer and thiner glue. this is the reason why i say to heat up the whole screen assemby including the backside, to make it easyer to unstuck the glass and scren thats glued to it.
- once you get a bit of a foothold in the upper corner between and the glassand the frame you continue the folowing procedure again and again until the glass and screen detaches from the frame:
-every 2 minutes or so , when i feel the asemby cooled down, i'd heat up the whole assembly for 5 seconds or so, than concentrate on the spot i worked on for another 5 seconds, than move/push the exacto knife a bit. dont force it. after a while youl get a feel of it. if the exacto knife happend to be out, i would heat up the blade after heating up everything else, and than put the blade in.
prevent the freed parts from sticking back to the frame by using the rest of the exacto knife blades as shims.
once it detaches it should look like photo 5- the glass glued to the screen.
- now we have to detach or unglue the glass from the screen.
procedure is the same: start somewhere, heat, put knife in, etc... i used a second knife as shim folowing the first knife, and after avery couple moves i would get the knife out and wipe off the epoxy glue. heat the blade and put it back in.
when finished you should have something like photo 6 and 7: free screen covered in glue epoxy residue.
- now we have to get rid of the glue residue. i took the bulk of it usinga flat exacto knife blades like the one in photo 8 and 10. just warm the place a bit with the air gun and scrape it off with the blade. to clean what was left i used a bit of goo gone on a pice of cloth or napkin photo 9.
cleaned screen can be seen in photo 11 - sadly out of focus.
if u are like me and r impatient to test the screen you can just connect with just the side connector like in photo 12 and 13. the upper connector is for the s pen digitizer. side connector is for the screen and touch digitizer.
now all that's left is to put the phone back together except leave the new glass for last.
-first thing is to put the screen(without the glass) back on the frame. try to center it just right, so that ther's a little bit of space between the sides of the screen and the frame.
at this point all that will hold the screen to the frameis the thin layer of glue on the back of the screen. after centering and lowering the screen in the frame procede to put the phone back together folowing in reverse order the same steps used to disasambe it. when finished you should end up with the whole functioning phone except the front glass -as seen in photo 14.
now you can chose to trim and put a screen protector on the scree so as to fill the empty space between the screen and the glass - the space where the glue was, or you can just leave it empty. you can put a screen protector anytime after by removing the glass. which should be much easier to remove now that its held in place only by the blach sticky tape on the edges. just use some suction cap to remove it, starting at an age, and remove it like fliping a page. see photo 16. i used the note for 2 weeks without the screen protector in the empty space and it worked without a problem onlt thing was that when i pushed hard the glass would touch the screen and leave a bit of dirt in that place. thats why i decided to put the screen protector to fill the void. in photo 15 i raised the screen protector to make it visible in the photo.
if you are like me and worry that somehow the glass might fall off the phone you can always get a hard plastic case for the phone, like the one in the pics. it's made of 2 parts. one goes on the back one on the front and they snap togeter around the phone. this will hold the glass in place no matter what while it will also protect the phone.the case is in photos 17 and 18. i got this one of ebay for 8$ and free shipping.
the last thing to be done is:
for some reaseon the touch screen became much more sensitive after removing the glue so you need to lover the touch sensitivity. for this get the touchscreentune app from the market. it works with galaxy note and galaxy s2. put the sensitivity from the recomended 25 to 50.
the best thing about this procedure is that i dont have to worry about the f ing glass anymore. if it brakes again i'l just order another one and in under 2 minutes i can replace it. all i have to do is get the phone case off, put a suction cap on , , remove the old glass , and put the new glass. that's it.
because it takes 4 to 8 hours i would recommend the process to be done in 3-4 sessions as people would get tired after 2 hours of work and tend to lose focus, attention, patience and start to push to get it faster done, and that's when bad stuff happens like yellow spot burn on the screen or small scratches. another thing about scratches, even if u manage to scrach the screen dont worry to much as the scratches are almost invisible when the screen turns on. youl see what i mean ....
i do have one question: WHY DID SAMSUNG DECIDE TO GLUE THE SCREEN TO THE GLASS INSTEAD OF HAVING THEM SEPARATE LIKE ALL THE OTHER TOUCHPHONES?

I do the same for Galaxy S. I removed broken pieces of glass from device using guitar pick and carefully glued a new glass on each side. 9$ (free delivery) on ebay.

blank for future use
blank for future use

anonymous572 said:
I do the same for Galaxy S. I removed broken pieces of glass from device using guitar pick and carefully glued a new glass on each side. 9$ (free delivery) on ebay.
Click to expand...
Click to collapse
what kind of glue did you use? where did u get the glue from? how did u do it?
i didnt glue the glass back to the screen. i just put the glass on the frame. to fill the void where the glue was i trimed a regular screen protector and put it inbetween the glass and the screen. but it works same without it.

Very interesting, I didn't think it was possible because the glass is glued to the SAMOLED panel. I'm very glad that I am wrong.
As much as I hate to think about it, a guide like that would probably come in handy for many of us at some point.
*knocks on wood*

pboesboes said:
Very interesting, I didn't think it was possible because the glass is glued to the SAMOLED panel. I'm very glad that I am wrong.
As much as I hate to think about it, a guide like that would probably come in handy for many of us at some point.
*knocks on wood*
Click to expand...
Click to collapse
Nothing is impossible with the right tool and know-how . The glue could probably be uncured with a heat gun, just like ipad. The challenge is not damage the panel and make sure it is dust free after put back the replacement.
It is said impossible because of the difficulty involved. If you can't manage to install a screen protector with perfect alignment and zero dust spike, this task is not for you.
@drevilatwork Thank you for writing this step by step guide!

I dropped my phone last night and it landed face down, cracking the glass.
I'm so upset, but I don't think I have the skills or the tools to do this job myself. I am relieved to learn that the glass can be replaced, but do you know whether the Samsung agents are likely to be able to do this?

they probably wont do it. but you can try showing this thread to some technician or phone repair shop and they might do it for you. they also might charge you a lot to the point where it might be more convenient to just buy a new 260$ screen.

looks scary dude

all im going to say is good luck separating the 2 screens without breaking the lcd or scratching the crap out of it ... this is a 90% epic fail method but thumbs up to the few that may succeed or dont mind their screen looking like its been belt sanded...

Its worth a try, since screen replacement costs 230 euros.

kawgirlval69 said:
all im going to say is good luck separating the 2 screens without breaking the lcd or scratching the crap out of it ... this is a 90% epic fail method but thumbs up to the few that may succeed or dont mind their screen looking like its been belt sanded...
Click to expand...
Click to collapse
actually .. the funny thing is that even if u manage to screch the screen and / or leave dirt behind it doesn't show while the phone is on. it might show when is off but not when is on. i was suprised about that too. and secondly, having to do it again knowing what i know now i would do it without leaving a mark. and in the end is certenly worth a shot before ordering the 260$ screen assembly. the special thing that it requires is pacience and attention.

Why different prices for all the same lenses in this shop ?

drevilatwork said:
actually .. the funny thing is that even if u manage to screch the screen and / or leave dirt behind it doesn't show while the phone is on. it might show when is off but not when is on. i was suprised about that too. and secondly, having to do it again knowing what i know now i would do it without leaving a mark. and in the end is certenly worth a shot before ordering the 260$ screen assembly. the special thing that it requires is pacience and attention.
Click to expand...
Click to collapse
as i said good luck with it and hope you make some money doing it..... ive successfully done the same thing myself but other than it will never look good like a factory screen (not even close), the amount of time it takes to make it look anywhere near acceptable (not like a 10 dollar repair) is big and that makes the repair not really worthwhile doing it for anyone but yourself and even then who spends 700-800 dollars on something and does a repair that makes it look cheap... then theres the whole ordeal of the membrane youre taking the adhesive off of along with the HUGE chance of damaging it.. it is placed with precision and adhered for a reason along with being dust and scratch free... this is a repair that just wont last because things will start functioning improperly for multiple reasons...
im not knocking you or anyone who tries this..im just trying to emphasize the dangers, downfalls and the probability of it being a legit solid repair. also the resale value when the next greatest thing comes along... just beware....

Hmmmm
Well chaps I hate to disagree here, but after speaking to the technical bods at Samsung it appears that the OLED is NOT glued to the glass, but the glass is laminated and bonded in, much like a car windscreen. My screen got broken the other day and I have read the 2 posts on XDA regarding this. Now if you go and have a look at the pics of the other post
http://forum.xda-developers.com/showthread.php?t=1487716
you can clearly see the OLED, although broken, seperated from the glass with no sign of any glue. The reason it broke is that upon heating the glass you will melt the glue, which will then stick to the edges of the OLED and if you pry it at the wrong place/time/too hard/whatever you will break the OLED as it is glued to the bezel itself. So when my glass arrives I am going to attempt to remove the glass using fishing line and pulling it between the glass and the bezel and OLED to release it, the same way as I used to remove car windscreens, and post the results here. I have also been told that the reason for the sticky "epoxy" mess that you encountered in this postis from melting the plastic on the back of the glass (which is the lamination!) by using too much heat.....I mean come on, a heat gun is a bit excessive!! Prying the screen out a bit at a time might work, but will surely end in tears, where as cutting the cold adhesive with a fine nylon cable, which wont scratch the OLED, might just work. I'll keep you posted on my results.

Just throwing an idea out there: maybe the adhesive would be easier to defeat when it's really cold, rather than really hot. I know a lot of adhesives become quite brittle when you put them in the freezer, superglue and epoxy for example. And the electronics/plastics of the display could be relatively fine with the low temps.

pboesboes said:
Just throwing an idea out there: maybe the adhesive would be easier to defeat when it's really cold, rather than really hot. I know a lot of adhesives become quite brittle when you put them in the freezer, superglue and epoxy for example. And the electronics/plastics of the display could be relatively fine with the low temps.
Click to expand...
Click to collapse
this is not one of them...i can guarantee this 100%
learn how a digitizer is made then you might see the light, and not just the light of white trash repair and failure...
ive explained it in great detail many times... and btw just because im a girl doesnt mean what im saying is wrong... 20+ years in the industry gives me sort of a clue as to what im saying..
im trying to help people avoid a long drawn out disaster and to waste $20(which is NOT gorilla glass) plus all of the other things they buy to try to make this a success which will never happen...
and fyi freezers, superglue and epoxys are big no no's...they are not used by any factory so there is another myth busted... they will just add to the destruction... 100% guarantee

kawgirlval69 said:
this is not one of them...i can guarantee this 100%
Click to expand...
Click to collapse
What do you mean? One of what?
learn how a digitizer is made then you might see the light, and not just the light of white trash repair and failure...
Click to expand...
Click to collapse
I know how a digitizer is made.
ive explained it in great detail many times... and btw just because im a girl doesnt mean what im saying is wrong... 20+ years in the industry gives me sort of a clue as to what im saying..
Click to expand...
Click to collapse
I had no idea you were a girl and I don't see why that matters. Experience is the industry is of course relevant, if your particular field in the industry was related to repairs. But I don't know if it is?
im trying to help people avoid a long drawn out disaster and to waste $20(which is NOT gorilla glass) plus all of the other things they buy to try to make this a success which will never happen...
Click to expand...
Click to collapse
The glass on the Note is Gorilla glass: http://www.corninggorillaglass.com/products-with-gorilla/full-products-list
and fyi freezers, superglue and epoxys are big no no's...they are not used by any factory so there is another myth busted... they will just add to the destruction... 100% guarantee
Click to expand...
Click to collapse
I didn't say factories use superglue or epoxy, or freezers for that matter. But the fact that factories don't use them doesn't mean it can't work for DIY repairs. Low temperature brittleness isn't exclusive to epoxy or superglue. Many, many glues (and other materials) have that property.

pboesboes said:
What do you mean? One of what?
I know how a digitizer is made.
I had no idea you were a girl and I don't see why that matters. Experience is the industry is of course relevant, if your particular field in the industry was related to repairs. But I don't know if it is?
The glass on the Note is Gorilla glass: http://www.corninggorillaglass.com/products-with-gorilla/full-products-list
I didn't say factories use superglue or epoxy, or freezers for that matter. But the fact that factories don't use them doesn't mean it can't work for DIY repairs. Low temperature brittleness isn't exclusive to epoxy or superglue. Many, many glues (and other materials) have that property.
Click to expand...
Click to collapse
i mean exactly what i wrote... as per your idea... this wasnt one that would work... my god man do i have to spell everything out for you???
obviously you dont know how a digitizer is made or you wouldnt have spouted the crap you have... bottom line
the girl part..well some dont think women know anything..its a culture thing.. but as for you not knowing if my particular field in the industry was related to repairs my god ive only said it multiple times in multiple posts... but since you dont like to read i'll say it again..20+ years board level factory trained.. motorola, audiovox, nokia, samsung... and this is a samsung forum so i think i have my tech qualifications covered here... again READING IS GOOD... work on that...
again you just dont read or have horrible comprehension because i never said the notes screen wasnt gorilla glass i said the $19 one wasnt... seriously every time you type something you dig yourself a deeper hole...
your superglue and epoxy blather just shows you dont have a clue and dont read... really they dont have any place in the screen/lcd part of diy.. its just trouble looking for a place to happen... now if the plastic housing needs repaired maybe but still not a top ten choice... if you had a clue you would know the proper adhesive to use... and its easily found... you are just too much...
seriously...just give it a rest... i wasnt bashing on you and have said it ive also said all im trying to do is help people not make a bad decision... and THIS IS A BAD DECISION...
you want me to play nice (which i really am..most other forums here would have totally lowered the boom on you for spouting crap... ive been really nice.. to keep it that way just go post somewhere where you can be productive... here youre not... im sure you have some great ideas but nothing you have said in this thread is remotely good.. sorry but it is what it is...
beep beep

kawgirlval69 said:
i mean exactly what i wrote... as per your idea... this wasnt one that would work... my god man do i have to spell everything out for you???
Click to expand...
Click to collapse
The sentence made no sense considering what it was replying to. Not my fault you were unclear/ambiguous.
obviously you dont know how a digitizer is made or you wouldnt have spouted the crap you have... bottom line
Click to expand...
Click to collapse
Ok?
the girl part..well some dont think women know anything..its a culture thing.. but as for you not knowing if my particular field in the industry was related to repairs my god ive only said it multiple times in multiple posts... but since you dont like to read i'll say it again..20+ years board level factory trained.. motorola, audiovox, nokia, samsung... and this is a samsung forum so i think i have my tech qualifications covered here... again READING IS GOOD... work on that...
Click to expand...
Click to collapse
Reading is very good, but you can't assume everyone in a public forum has read every single post of yours and remembers every detail. What isn't helping is the lack of proper punctuation and formatting which make your posts unpleasant to read.
again you just dont read or have horrible comprehension because i never said the notes screen wasnt gorilla glass i said the $19 one wasnt... seriously every time you type something you dig yourself a deeper hole...
Click to expand...
Click to collapse
Replacement screens are generally OEM parts.
It might appear I'm in a hole, but that's only because I live in Holland and am below sea level. I assure you I haven't done any digging.
your superglue and epoxy blather just shows you dont have a clue and dont read... really they dont have any place in the screen/lcd part of diy.. its just trouble looking for a place to happen... now if the plastic housing needs repaired maybe but still not a top ten choice... if you had a clue you would know the proper adhesive to use... and its easily found... you are just too much...
Click to expand...
Click to collapse
I wasn't suggesting to use superglue or epoxy, read it again.
seriously...just give it a rest... i wasnt bashing on you and have said it ive also said all im trying to do is help people not make a bad decision... and THIS IS A BAD DECISION
Click to expand...
Click to collapse
I get that, and appreciate your concern. However, you should understand that some people like to try things even when the chance of success is not very high. You seem to be one of us in that regard (you attempted repairs yourself too, right?), so I don't see why it upsets you so much.
you want me to play nice (which i really am..most other forums here would have totally lowered the boom on you for spouting crap... ive been really nice.. to keep it that way just go post somewhere where you can be productive... here youre not... im sure you have some great ideas but nothing you have said in this thread is remotely good.. sorry but it is what it is...
beep beep
Click to expand...
Click to collapse
I don't care if you play nice or not. I appreciate honesty. Now for some honesty in return: you're not helping in this thread.
All you do is say people's ideas are stupid without giving arguments that aren't arguments from authority. And I would very much appreciate it if you would stop misrepresenting my posts (intentional or not).

Dropped my N7 in the toilet

Kinda embarrassing, but I had the tablet on the water take and when I flushed it just slipped right into the bowl...
Power button isn't really working.. took the back off of it and have it laying glass up hoping the water drains out of it. Not like there is alot of water in it or anything just want to be sure. Hopefully their isn't significant damage, but if there is I hope I can RMA it..
ugh.

The lesson here is to take a newspaper or magazine with you when you need to poop, instead of expensive gadgets.
/or bring some action figures if you are really young at heart

moinster said:
Kinda embarrassing, but I had the tablet on the water take and when I flushed it just slipped right into the bowl...
Power button isn't really working.. took the back off of it and have it laying glass up hoping the water drains out of it. Not like there is alot of water in it or anything just want to be sure. Hopefully their isn't significant damage, but if there is I hope I can RMA it..
ugh.
Click to expand...
Click to collapse
put it inside a bag of rice overnight. hope that helps.
---------- Post added at 09:52 AM ---------- Previous post was at 09:51 AM ----------
Cryingmoose said:
The lesson here is to take a newspaper or magazine with you when you need to poop, instead of expensive gadgets.
/or bring some action figures if you are really young at heart
Click to expand...
Click to collapse
aye.
the issue is, i lose count how many times my GI Joes had a little "cyclone adventure".

moinster said:
Kinda embarrassing, but I had the tablet on the water take and when I flushed it just slipped right into the bowl...
Power button isn't really working.. took the back off of it and have it laying glass up hoping the water drains out of it. Not like there is alot of water in it or anything just want to be sure. Hopefully their isn't significant damage, but if there is I hope I can RMA it..
ugh.
Click to expand...
Click to collapse
RMA is for warranty repair only.
In your case, it's accidental damage which would/should not be covered by warranty.

Disconnect the battery immediately and let it sit in a dry area for at least a day. I'd even recommend hitting it with a hair dryer for 5-10 minutes. My daughter left her phone out in the rain, and when we found it, water literally poured out of the case. I took the battery out, disassembled it as much as I could and let to dry for a day. It survived and it working fine now. Keep in mind that most manufacturers place "moisture indicators" inside their devices. It's just a small paper sticker with tiny drops of red dye on it. As soon as water hits it, the dye runs and the sticker turns pink... and your warranty is void.

Sorry dude. Be more careful next time. Not sure what else to say.

ED2O9 said:
Disconnect the battery immediately and let it sit in a dry area for at least a day. I'd even recommend hitting it with a hair dryer for 5-10 minutes. My daughter left her phone out in the rain, and when we found it, water literally poured out of the case. I took the battery out, disassembled it as much as I could and let to dry for a day. It survived and it working fine now. Keep in mind that most manufacturers place "moisture indicators" inside their devices. It's just a small paper sticker with tiny drops of red dye on it. As soon as water hits it, the dye runs and the sticker turns pink... and your warranty is void.
Click to expand...
Click to collapse
Yeah it's powered off. Looking online right now how to disconnect the battery, also looking for the water detection sticker.

ED2O9 said:
I'd even recommend hitting it with a hair dryer for 5-10 minutes.
Click to expand...
Click to collapse
If his warranty wasn't void before...

sinhumane said:
ok, as a professional repair tech i can tell you that rice has a VERY low chance of success... it isnt as marvelous as everyone thinks it is. it wont absorb much of the moisture in the phone. i have seen numerous phones come through my shop after sitting in rice for days... STILL have standing water in them.
your best bet: if you have tools to take it apart, remove the board, and immediately put it in alcohol. if you have any residual corrosion on the board, take a VERY soft bristled brush and gently wipe the corrosion away.
if you dont have tools/a brush... take the battery out, and submerge the entire thing in 91% (nothing less) rubbing alcohol. you may ruin the lcd, but trust me, a new lcd is a far cry cheaper than a new phone.
also, your battery is likely toasted, buy a new one.
just as a caveat to all, unless you drop your phone in clean city tap water, or distilled water... its going to have contaminants in it, and will corrode your phone, rice or no rice. alcohol displaces the moisture, and removes chemicals/minerals on your board.
Click to expand...
Click to collapse
Try these tips. This guys a pro and he recently helped someone that dropped his phone in the pool.

Po1soNNN said:
Try these tips. This guys a pro and he recently helped someone that dropped his phone in the pool.
Click to expand...
Click to collapse
Thank you. I've disconnected the battery and it is sitting in the server room, Dry and Moisture free, yes? I've try some of the tips when I find the alcohol.

putting it in a sealed bag full of silicon gel sachets will also help.

That's a crappy situation.
If you're in the US and paid the full amount on your credit card (not debit card), see if the card offers any buyer's protection. American Express and the higher tier Visa cards offer a 90-day theft and breakage protection.

moinster said:
Thank you. I've disconnected the battery and it is sitting in the server room, Dry and Moisture free, yes? I've try some of the tips when I find the alcohol.
Click to expand...
Click to collapse
Is the battery dry? If it's wet you'll need a new one and remember this isn't guaranteed to work.

moinster said:
Thank you. I've disconnected the battery and it is sitting in the server room, Dry and Moisture free, yes? I've try some of the tips when I find the alcohol.
Click to expand...
Click to collapse
A server room should dry it out good.
This is going to sound pretty gross, was the toilet flushed? I recently repaired my HTC Hero that I had loaned to a friend, who then proceeded to drop it down an unflushed toilet
I dried it out, only to find it would not power up, not until I remove the pubic hair that was shorting it out
Just Something to look out for.

Just because the battery got wet doesn't mean that it's trashed. Tap water isn't that great of a conductor, so as long as the battery didn't discharge at too high of a rate from a short, it might be okay. If the battery felt very hot when you removed back cover, it's not a good sign.
As for the alcohol, I'd use it to clean the board but I'd hold off on submerging the whole unit. The openings on the Nexis's case are pretty thin, so I doubt much water got inside. I'd just let it dry and see if it works before doing anything drastic.

moinster said:
Kinda embarrassing, but I had the tablet on the water take and when I flushed it just slipped right into the bowl... Power button isn't really working.. took the back off of it and have it laying glass up hoping the water drains out of it. Not like there is alot of water in it or anything just want to be sure. Hopefully their isn't significant damage, but if there is I hope I can RMA it..
ugh.
Click to expand...
Click to collapse
If it was on when you dropped (probably was) it might have shortened something in the circuit board, and that is why is not turning on, however there is always hope and I would follow the previous advices to disconnect the battery, hair dryer and rice of bag overnight before trying turn on again.
Good luck!!

trevd said:
A server room should dry it out good.
This is going to sound pretty gross, was the toilet flushed? I recently repaired my HTC Hero that I had loaned to a friend, who then proceeded to drop it down an unflushed toilet
I dried it out, only to find it would not power up, not until I remove the pubic hair that was shorting it out
Just Something to look out for.
Click to expand...
Click to collapse
Hahaha, It was at the end of its flush when it slipped it. When it hit the bowl the case opened a little bit but I grabbed it as fast as I could.
ED2O9 said:
Just because the battery got wet doesn't mean that it's trashed. Tap water isn't that great of a conductor, so as long as the battery didn't discharge at too high of a rate from a short, it might be okay. If the battery felt very hot when you removed back cover, it's not a good sign.
As for the alcohol, I'd use it to clean the board but I'd hold off on submerging the whole unit. The openings on the Nexis's case are pretty thin, so I doubt much water got inside. I'd just let it dry and see if it works before doing anything drastic.
Click to expand...
Click to collapse
The battery was quite cool actually.
It was clean tap water, btw.

Another sad story: I dropped mine 4 feet to a concrete floor about 24 hours after it was delivered, breaking the screen. The display still works, but the digitizer won't respond to touches any more. I found a link to a place that claims to have the screen-digitizer assembly for $130, but haven't pulled the trigger.
No luck with the VISA purchase protection...

UnusualSuspect said:
Another sad story: I dropped mine 4 feet to a concrete floor about 24 hours after it was delivered, breaking the screen. The display still works, but the digitizer won't respond to touches any more. I found a link to a place that claims to have the screen-digitizer assembly for $130, but haven't pulled the trigger.
No luck with the VISA purchase protection...
Click to expand...
Click to collapse
Yeah, I'm pretty damn clumsy :/ and I bought it with a debit card.
If the digitize is $130 I would just spend the extra $70 and sell the unusable one as parts.

trevd said:
A server room should dry it out good.
This is going to sound pretty gross, was the toilet flushed? I recently repaired my HTC Hero that I had loaned to a friend, who then proceeded to drop it down an unflushed toilet
I dried it out, only to find it would not power up, not until I remove the pubic hair that was shorting it out Just Something to look out for.
Click to expand...
Click to collapse
This had me giggling in my little cubicle.

Oem glass used as screen protector

I recently crack my screen on my OP3t... Save the first couple incidents, I found that ordering the parts and doing the labor myself saved a lot of money, It also was kind of fun (yea I am one of those guys). Anyway, Before doing any research what so ever on the tear down and repair I ordered an OEM original piece of glass considering that both the digitializer and LCD were both working well. My confidence rapidly depleted when I started the research and came to the conclusion that this particular repair was beyond my pay grade. I reached out to OnePlus and astonishingly they only charged around $65 USD for the parts, labor and shipping. Which is very reasonable considering that I couldn't find a display assembly for less the a hundred dollars. While my phone was still being repaired the glass I ordered arrived and I was blown away about the quality of glass. So my question is... would I be able to use the replacement glass in place of a tempered glass screen protector? With the glass they send both UV Loca Glue and Mini tools and an UV flashlight to activate the glue that from what I've read dries completely clear.. My fears about this are would it decrease the touch sensitivity of my phone and if no how would I apply the glue. IE. All over the glass or around the corners.... I obviously have no idea but I do know that if this is possible I would be ecstatic! thank you for your time and look forward to hearing the response.. Randy

I would not recommend using the LOCA for this at least. It'll be a true pain in the ass to remove if/when that time comes. If anything I'd try using an OCA film, if you can get your hands on one that fits.

Well, that could actually make some sense
As for the glue, that could actually be the trickiest bit.
Most of the bi adhesive strips would actually be too thick. And permanent glue could be a pain in the arse to remove.
Not sure the LOCA glue would actually work, as you'd need to only glue the two white/black bands on above and below the screen area so the UV wouldn't really get there.
Maybe a few drops of Loctite? That could be enough to keep it in place.
If you fancy giving it a try let us know how it works, finding a proper tempered glass screen protector proved to be quite "challenging"

i2andog said:
I recently crack my screen on my OP3t... Save the first couple incidents, I found that ordering the parts and doing the labor myself saved a lot of money, It also was kind of fun (yea I am one of those guys). Anyway, Before doing any research what so ever on the tear down and repair I ordered an OEM original piece of glass considering that both the digitializer and LCD were both working well. My confidence rapidly depleted when I started the research and came to the conclusion that this particular repair was beyond my pay grade. I reached out to OnePlus and astonishingly they only charged around $65 USD for the parts, labor and shipping. Which is very reasonable considering that I couldn't find a display assembly for less the a hundred dollars. While my phone was still being repaired the glass I ordered arrived and I was blown away about the quality of glass. So my question is... would I be able to use the replacement glass in place of a tempered glass screen protector? With the glass they send both UV Loca Glue and Mini tools and an UV flashlight to activate the glue that from what I've read dries completely clear.. My fears about this are would it decrease the touch sensitivity of my phone and if no how would I apply the glue. IE. All over the glass or around the corners.... I obviously have no idea but I do know that if this is possible I would be ecstatic! thank you for your time and look forward to hearing the response.. Randy
Click to expand...
Click to collapse
Use ALTECO or Super Glue on top and bottom plus a bit on both sides. :silly:

Mission OEM GLASS ABORT
Quick update... The day after I made this thread my 3 year old daughter was running to me estaticly because she took a sh!t in the potty... (fyi: Potty Training sucks) Anyways during her excitement she accidentally knocked my op3 off of the table next to the chair I lounge in most of the time. Its not a high table by an means maybe 3ft (1 meter).. Ruffly.. Anyways it landed and on very soft carpet.. (You know the spots on the carpet that are still brand new because they never experience being walked all over.. Like the high traffic areas of the same piece of carpet... Its Like if you're going to drop your phone on the carpet... That's the spot you aim for..{ADHD BAD}).. to be honest I didn't even know it fell until I went to look for it like a hour later... When I picked it up... I was the one sh!tt!ng my pants..

i2andog said:
Quick update... The day after I made this thread my 3 year old daughter was running to me estaticly because she took a sh!t in the potty... (fyi: Potty Training sucks) Anyways during her excitement she accidentally knocked my op3 off of the table next to the chair I lounge in most of the time. Its not a high table by an means maybe 3ft (1 meter).. Ruffly.. Anyways it landed and on very soft carpet.. (You know the spots on the carpet that are still brand new because they never experience being walked all over.. Like the high traffic areas of the same piece of carpet... Its Like if you're going to drop your phone on the carpet... That's the spot you aim for..{ADHD BAD}).. to be honest I didn't even know it fell until I went to look for it like a hour later... When I picked it up... I was the one sh!tt!ng my pants..
Click to expand...
Click to collapse
That sucks man and that happened from hitting the carpet ?

don't use any glue on top of cracked glass. remove screen from plastic frame, separate with cutting wire, clean old oca film, apply loca and new glass, and leave under uv lamp for 30-90mins. don't be lame with such waste of time and glass on top of cracked.

That damage seems excessive for falling a few feet onto carpet... Perhaps it's time to invest in a case

genuine55 said:
That sucks man and that happened from hitting the carpet ?
Click to expand...
Click to collapse
Yes... It is the reason for my indecisiveness on how to proceed forward... Because I honestly just received the phone from the repair center from the first broken screen... and for it to fall... on Charmin soft carpet and break like that is beyond my understanding... I absolutely love this phone because in my opinion it is the closet phone that would be comparable to the nexus line... but if this bullsh!t keeps up I might as well just buy a friggin' Pixel.. For perspective I purchased the 3t to replace my LG G5 which is not broken... but it is very limited on the software side.. not my cup of tea... but the thing is a tank. I have dropped that phone at times where I just knew before I picked it up that the screen was shattered... but that was never the case. The thing is still 100 percent OEM... I am starting to get hesitant about throwing anymore money at it.. I guess ill wait for a response from OnePlus support to see which pill I should take.. red or blue?? f*ck it.. ill take both
acmerw said:
don't use any glue on top of cracked glass. remove screen from plastic frame, separate with cutting wire, clean old oca film, apply loca and new glass, and leave under uv lamp for 30-90mins. don't be lame with such waste of time and glass on top of cracked.
Click to expand...
Click to collapse
That you for the tutorial my friend but I am assuming you misunderstood the content of this post. I broke my phone, purchased glass, sent phone to OnePlus Service, Glass arrived while phone was being repaired, received phone back, was curious if I could use glass as screen protection, broke phone again, $h!t my pants..

Anova's Origin said:
That damage seems excessive for falling a few feet onto carpet... Perhaps it's time to invest in a case
Click to expand...
Click to collapse
You're [email protected] right it is... That honestly crossed my mind. They f'ed up somehow.. skipped a step... who knows.. Or, maybe, just maybe the glass they used was defective.. Long shot but at least it would make sense.. Anyways imma get a joint venture on their a$$ like the ppl are doing to LG over the bootloops... Whos with me??

Anova's Origin said:
That damage seems excessive for falling a few feet onto carpet... Perhaps it's time to invest in a case
Click to expand...
Click to collapse
OOOOhh... My bad broski... I thought you meant a court case... Not something that was attached to the phone like pictured below

Ali will always be there for us.
Get the whole packages(Screen, LCD and Frame), No need Loca Loca Boca Boca.

Chainwater said:
Ali will always be there for us.
Get the whole packages(Screen, LCD and Frame), No need Loca Loca Boca Boca.
Click to expand...
Click to collapse
believe it or not.... it is much cheaper then buying the parts and doing the work myself compared to sending it to the repair center without worries of more damage.
I just realized that the way I wrote this is confusing af
It is cheaper to send my phone to the repair shop then to purchase the part off the internet... that is if you purchase the display assembly.. the glass runs around $5 usd the assemblies are well over $100 usd. If you know of anywhere I can get the assembly cheaper please let me know

I dropped my M20P..and guess what happened

No screen protector, only Huawei silicone case.
I had wire connected phone to laptop, heard doorbell, grabbed the fone and jumped off the bed, cable snapped out, phone slipped off my hand, flew two feet away from the bed and at a hight of around 2-3 feet, and fell flat on ceramic tile floor.
Thud! It sounded plastic-like, screen was facing upwards. I thought at least a shatter, picked it up and guess what.... nothing happened, screen is absolutely fine, not even a single scratch (also given that I have keys and phone in the same pocket most of the time).
Strike one

Wtf?

Strike one because your phone didn't break?

I get it, it's concerning/annoying to get such unexpected results when something like this happens. But don't worry, maybe "better luck" next time!
Btw, I wonder how much it would cost to replace the display as I assume it's not covered by the warranty?

jhs39 said:
Strike one because your phone didn't break?
Click to expand...
Click to collapse
For my carelessness since this is the first drop after purchasing the phone.

charliebigpot said:
I get it, it's concerning/annoying to get such unexpected results when something like this happens. But don't worry, maybe "better luck" next time!
Btw, I wonder how much it would cost to replace the display as I assume it's not covered by the warranty?
Click to expand...
Click to collapse
I need to get serious about going for a good casing, screen replacement will burn pocket really bad. M20Ps repairability score is 4/10 and that's not good.

rakesh2002 said:
I need to get serious about going for a good casing, screen replacement will burn pocket really bad. M20Ps repairability score is 4/10 and that's not good.
Click to expand...
Click to collapse
I just ordered this case (mentioned in the cases thread)
https://www.amazon.com/Spigen-Hybrid-Designed-Huawei-Mate/dp/B07K2H1CN8

We carpeted most of our rooms with a thick soft carpeting. Saved a lot phones, tablets and other objects since.
Sent from my LYA-L29 using Tapatalk

If you are seriously concerned about damaging your M20Pro in a fall/drop the 2 available UAG cases might be worth considering. I bought one but to me it was too bulky and made the phone uncomfortable to hold. Some people seem to love those cases.

Question Dropped/broken screen? Testing/options?

Greetings,
Dropped my phone a full foot. Now the screen flickers green. I'm guessing the screen is broken. Any way to test that other than replacing it?
How do screen replacements go with this device? I'm pretty handy myself and might even attempt it if I could confirm it's the screen that's broken. I've done my own screen replacements before, but it's been some time.
Any chance the screen ribbon cable could be loose? There is no visible damage.
Thanks.
PS: of course, I have no insurance/protection. Oii.

Don't feel too bad, one time I dropped a pro cam on a ESD padded work bench top from about 6 inches and did more damage to that $7G cam than your smartphone retails for
$hit happens even in controlled environments... get a good case moving forward.
It could be a loose connector.
Or a fractured solder joint. The BGA chipsets don't like it when the mobo flexes.
You could replace the display only to learn it was actually a mobo failure. I lean more towards a mobo failure if there's no visible damage to the display.
Pull the cover and inspect it... an easy fix is always a great fix.

blackhawk said:
...Or a fractured solder joint. The BGA chipsets don't like it when the mobo flexes.
Click to expand...
Click to collapse
Oii... Thanks for this thought; I was afraid of something like this.
Makes me wonder if metal/glass phones hold up better?

ToryEarly said:
Oii... Thanks for this thought; I was afraid of something like this.
Makes me wonder if metal/glass phones hold up better?
Click to expand...
Click to collapse
May not be as bad as it seems...
On my Note 10+'s I use the Zizo Bolt case. Without it my first one would be history by now, if it doesn't corner hit on a drop it face plants. I've dropped it close to a dozen times from 1-4 feet onto concrete with zero damage. I don't like handling it without a case as it's a slippery fish
A good case reduces/lengthens the G loading spike making impacts survivable as well as protecting the exterior.
A 2 layer design like the Bolt provides excellent drop protection. It's important that the out shell or whatever holds the case together doesn't come loose on impact...
For those memorable flying end over end multiple impact events. Even with a small drop though I inspect for damage.

I'm actually in a similar situation. Dropped my phone from about 1 or 2 feet and I have the green screen flickering as well. The phone works. I can get call and talk via headphones. But my question that I'm trying to figure out is if there is a way to put the phone into file transfer mode from a connected computer since I can't do it from the phone.

GrandAdmiral said:
I'm actually in a similar situation. Dropped my phone from about 1 or 2 feet and I have the green screen flickering as well. The phone works. I can get call and talk via headphones. But my question that I'm trying to figure out is if there is a way to put the phone into file transfer mode from a connected computer since I can't do it from the phone.
Click to expand...
Click to collapse
Developer options>usb settings.
You need to load the driver on the PC maybe too.

blackhawk said:
Developer options>usb settings.
You need to load the driver on the PC maybe too.
Click to expand...
Click to collapse
That's not the issue (already rooted). The screen is non-responsive.

GrandAdmiral said:
That's not the issue (already rooted). The screen is non-responsive.
Click to expand...
Click to collapse
Uh-oh. If it was working before the plunge you likely either had a connector dislodge or suffer a mobo failure from the impact.

It's happened to me twice both from barely 1 feet. The screen itself was not cracked. Ifixit luckily submitted it as a manufacturers defect since the screen wasn't broken. The first time they were nice enough to not wipe my phone. The second time they did wipe my phone without telling me. Something about their policy uh.
Ended up going with the poetic revolution case. And it's handled a 2ft drop without issue. Had the Spigen tough amor prior.
They said just replacing the screen resolved the issue.

Sorry to hear this OP.
$hit does happen.
I was using an old htc 10 for about 4 years, I finally upgraded to the Pixel 5 on release day.
About a month late, on my birthday I had it on my laptop and it drops flat faced down on the screen.
by some act of God I actually had a glass screen protector on it and had no damage!
I now don't use a scren protector, but oh well.
Somehow the back glass camera is cracked though, even though it wasn't ever dropped after this..
I think I'll look into the 5a instead of fixing it. It's not much more.

andybones said:
Sorry to hear this OP.
$hit does happen.
I was using an old htc 10 for about 4 years, I finally upgraded to the Pixel 5 on release day.
About a month late, on my birthday I had it on my laptop and it drops flat faced down on the screen.
by some act of God I actually had a glass screen protector on it and had no damage!
I now don't use a scren protector, but oh well.
Somehow the back glass camera is cracked though, even though it wasn't ever dropped after this..
I think I'll look into the 5a instead of fixing it. It's not much more.
Click to expand...
Click to collapse
The screen protector will transmit a lot of the G loading directly to the phone. Something is going to absorb that energy one way or another. Not always obvious either.
Ideally if you have a good case with raised display guards it will soak up enough of the energy so that nothing is stressed to the breaking point.
Mobos and cams are intolerant of high G loading and flexing. A monetary G spike of 2000Gs* can be generated by a fall from bench height to a hard floor. Hard materials absorb little energy unless they bend or break; they can readily conduct it though to internal assemblies... or the other side of the phone.
*how to destroy an IC by dropping it on the floor.

blackhawk said:
*how to destroy an IC by dropping it on the floor.
Click to expand...
Click to collapse
So you're saying I should probably be really gentle with these ceramic TD8749s and MD8755s then?

V0latyle said:
So you're saying I should probably be really gentle with these ceramic TD8749s and MD8755s then?
Click to expand...
Click to collapse
If they land on a hard floor on the body rather than leads they can pull enormous G's. As I got more experienced I was more careful not to drop IC's and to use ESD protocols with the more sensitive chips.
There are a couple of issues with dropped phones The internal bonds to the chip can be broken. Even more fragile is the mobo's solder flowed on components especially the BGA chipsets. No way to inspect those for damage. Internal mobo traces may also be opened. With bent frames and broken glass the odds the mobo or display will be damage increases.
Some of the cams have moving parts as well as their sensor's mounting points. More recently that became more of a concern to me as they aren't cheap and a pain to replace.
If the manufacturer uses lead free solder it's a death wish for the device. No lead solder is much more brittle and has poor flow characteristics making the bond is less secure.
Cell phones are exempt from the lead ban but who knows if they use it? No lead solder becomes even more brittle in cold temperatures. Conformal coating is also needed for fine pitch traces to prevent silver dendrites for forming with the no lead solder over time.

blackhawk said:
If they land on a hard floor on the body rather than leads they can pull enormous G's. As I got more experienced I was more careful not to drop IC's and to use ESD protocols with the more sensitive chips.
Click to expand...
Click to collapse
I was being sarcastic can't be too careful with 50 year old IC's

V0latyle said:
I was being sarcastic can't be too careful with 50 year old IC's
Click to expand...
Click to collapse
Didn't recognize the numbers. LM3914, I still be careful with that cool IC