Dopod 595 - HTC Breeze

Dear all,
I have tried to upgrade the ROM for my Breeze (Dopod 595) with Futureshock's firmware but was not able to do so. The device would not go into boot loader mode. Basically the device will reboot/restart when I press the camera and power button combination. I do see that my device CID = DOPOD001 via the mtty. The IPL=0.9 and SPL=2.05 Has anyone successfully upgrade a dopod device? Thanks.
Regards,
Kueh

Dear all,
I have found the answer to my own question. For what ever reason, I was not able to get camera and power button combination to work. However after 4 hours of trying, I have manage to get working. Here is how?.
1) Make sure that the ActiveSync is working and the device is connected and synchronized.
2) run the runme.bat
3) The step where the batch program ask for you the do press the camera and power button and press Enter. Do the following.
a) Press any key on the computer.
b) Wait for a moment.
c) A prompt will appear on the device to ask for permission to run the program.
d) Now hold down the power button (continue pressing until step f).
e) Press the Left soft key (the key nearest the screen on the left).
f) As soon as you do the step e, press the camera button down.
( For step from d to f, I have to get help from another person as it happen very fast especially from step e to f. If you miss it by half a second the machine will be rebooting.)
4) Now you should see the three colour screen.
5) Release the buttons that you are pressing
6) Continue with the instructions as per normal.
Hope this helps.
Regards,
Kueh.

when you are upgrade your device you must may sure that you have to do it fast !!!or you will be fail !!!i have try it over 10 times, the first time i upgrade my breeze!

Related

is possible to came back in wm2003?

i try to upgrade my pda2k with wm6...but screen remain with 4 stripes coloured...so i would to know if is possible to came back in wm2003.
thank you.
Yes, you can back to wm2003. By same as you upgrade to wm6. First of all, you might be have lastest official wm2003 or what ever you want. Then make your BA into boot loader mode (Power, REC and Reset at the same time), display will shown you "USB Serial. Put it to cradle or cable that connect to PC. Run your official rom and following the instruction.
thank you!
and where i can take this 2003 rom for my pda2k?
thank you
before you do... try to "Hard Reset" your WM6 first....
Steps:
1. Stick the reset button.
2. Quickly press and hold the two side buttons
(record + camera) simultaneously before the hardware display.
3. Select No Yes Yes in the given option
(press record to navigate on the three option)
(press camera to toggle Yes/No)
4. Press your mail button....
or second button from the left of your four button shortcut keys.
5. (optional) Cross your fingers and kiss your phone.
i've had that problem when i flashed mine with Xplode's ROM and that solved the problem.

How can I verify Hard-SPL is installed?

I need to verify that its installed before I proceed to flash my rom.
Also, what is a .nbh file used for?
BorrowADolla said:
I need to verify that its installed before I proceed to flash my rom.
Also, what is a .nbh file used for?
Click to expand...
Click to collapse
Hold down the power button & camera button at the same time then press the reset button with your stylus and keep holding the power & camera button...you should see the following
KAISXXX MFG
SPL-1.0.Olipof
CPLD-8
XXX is your model number, IE 130 120 100
I just learned this myself yesterday....
You need to press only the camera button (a deep press) together with the SR slot, and hold until you get the tricolor screen.
No need to press the power button as well.
thanks, i have it

Lost Password - Need Help ASAP - Touch HD

Hi Good people of XDA,
Having some spare time this evening, i thought i could indulge myself with some old flashing habit - thus i tried the wm 6.5 version from http://forum.xda-developers.com/showpost.php?p=3350560&postcount=265
And i am 100% sure i did put in the right password - and unfortunately for me i can't seem to remember the right password anymore, so i cannot get into the phone aat all. Could some one advice me on how to reset the phone or install a new rom, becasue i tried installing at fresh but active sync can't connect as expected.
Therefore i will be really greatful if some one can advice on how to get out of this nightmare.
...Please make my week end
Thanks for any advice in advance
Follow this method for installing a new rom.
------------------------------------------------------------------
You must flash HardSPL first to be able to flash this ROM!
* More info and instruction about HardSPL!
An alternative is USPL, it doesn't change your original SPL!
* More info and instruction about USPL!
SAFEST WAY TO FLASH YOUR ROM IS THROUGH STORAGE CARD METHOD:
* Copy BLACIMG.NBH into the root dir of your Storage Card.
* Be sure to have at least 30% of charge.
* Turn off your device by using the Power Button
* Go to Boot loader mode. Push and hold Vol. Down + press Power button.
* As soon as presented the message, push Power button to start flashing or Volume Down button to cancel.
* The whole procedure will take about 3 minutes. After you finish and see the relative message, soft reset your device, you are ready.
I figured it out Thanks - did a hard reset
To perform a HTC Touch HD hard reset
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:
3. Release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
jpmalum said:
Hi Good people of XDA,
Having some spare time this evening, i thought i could indulge myself with some old flashing habit - thus i tried the wm 6.5 version from http://forum.xda-developers.com/showpost.php?p=3350560&postcount=265
And i am 100% sure i did put in the right password - and unfortunately for me i can't seem to remember the right password anymore, so i cannot get into the phone aat all. Could some one advice me on how to reset the phone or install a new rom, becasue i tried installing at fresh but active sync can't connect as expected.
Therefore i will be really greatful if some one can advice on how to get out of this nightmare.
...Please make my week end
Thanks for any advice in advance
Click to expand...
Click to collapse
Well, did you solve your problem?

please help, my diamond won't boot up at all

Dear friends,
I was trying to flash my diamond with mtty, where i guess i messed up with commands, I formatted it, then tried to restart with "task 8" then my phone turned off and never on again no matter what i did or key pushed.
Any help will be much appreciated...
me too
but i don't know how to use Jtag recover BL for Diamond
Update ROM by using the BootLoader
Hello there,
even though you can't boot into your OS in the Diamond, there's a way to enter "BootLoader" mode. I'm not sure it works, but you can give it a try.
Here's how:
- Connect the Diamond to your PC
- Enter bootloader mode on your Diamond: with the device turned on, press and hold the volume down button along with the power button, then press the reset button with the stylus tip, then release the volume down and power buttons when bootloader tricolour screen appears.
- Use the ROM Update Utility. If the previous step worked and your connection is working, then with some luck you will be able to Flash the Device with the ROM update utility.
I've tried to find the thread that discussed this with pictures and such but couldn't. You might want to look for similar instructions
Good luck
Shane
JTAG
does anyone managed to JTAG diamond?

please i need serious help .....

hi ...
i have HTC opal and from while i have install a new ROM and it's work ok
then after two week .. my phone does'nt work he hang at boot screen
is there any way to format it with out it working .... please any help .
try a hard rest
Don't worry, your device is not damaged. Follow the guide here to fix your problem:
http://forum.xda-developers.com/showthread.php?t=685025
Note that you'll lose all data on your device when performing this fix. Hope you have a backup at hand!
Essential thing to be known:-
1. Bootloader mode Knowing how to enter into Bootloader mode is one of the most essential thing to be known for a opal user (windows mobile users).
How to enter?
There are two way to enter into bootloader mode.
1. If you device is on, open your device's back cover. Press the soft reset button ( red button ) using stylus. As soon as you press it, immediately press the volume down button and keep holding it until you see a tri-color screen on your device's screen.
2. If your device is off, press the power button as soon as the device vibrates immediately press volume down button and keep holding it until you see a tri-color screen on your device's screen.
Uses?
If you flashed a damaged rom, you would be no longer able to use your device. In that case enter into bootloader mode. And flash a different rom.
Click to expand...
Click to collapse
Good luck..
thnx .... i will try it ....

Categories

Resources