We are 3 friends with Qtek 2020i (Fans? ) and we face the same problem. The wifi connection will not be enabled unless i do a soft reset on the Qtek 2020i.
1.11.00 wwe
1.02.00
Is it that common? Anyone has an idea?
thanks
T,
Mine did it too, but after a hard reset, it was fine.
It must have been something that I had installed at some point.
Mine used to do it too but as soon as i upgraded it was fine.
Upgrade to the latest ROM version (if pos)
Tried to upgrade ROM for Xda IIs from O2 website and something went terribly wrong. Now all I have on my black screen is " USB - V2.07"
Can't get ActiveSync (4.0) to recgognize device, can't reset, nothing, I'm dead in the water. PLEASE, PLEASE HELP
My ROM version is:
English ROM
ROM: 1.31.00 WWE
Date: 12/13/04
Radio: 1.02.00
Protocol: 1337.32
ExtROM: 1.31.920 WWE
Was Upgrading to:
English ROM
ROM: 1.40.00 WWE
Date: 03/10/05
Radio: 1.12.00
Protocol: 1337.42
ExtROM: 1.40.923 WWE
MMS: 2.0.0.21
BT: 1.0.0 Build 3900
you're just stuck in bootloader mode...to get out of this simply press the power button + soft reset + record button at the same time
Tried, but nothing is happening
u must'nt be doing it properly..
just keep the power button and record button pressed..and then press the soft reset..or just reflash ur device once..
the worst case could be the hardware record button isnt workin properly
Thanks for your help, Beleive me I want it to work.
I keep pushing & holding the buttons while pushing reset, but nothing, I've even held all buttons & reset for over a minute, but still nothing. It looks like it wants to do something, the screen view "Serial - v2.07" starts to go dim but comes right back after I release the buttons/reset (It says "Serial" instead of USB when out of the cradle).
I'm open for any suggestions!
same thing happened to me with my xda 2s. I spoke to 02 technical services and apparently the unit is stuck between roms. The power button + soft reset + record button or camera button trick didn't work for me. I had to send it off to 02 to be repaired - it seems it can be reset but by 02. Sorry but I'm not that technically apt to explain anymore!
Know that it isn't good news at all but I hope that helps.And stops the panic a little...
Thanks, that does stop the panic of thinking I now have a dead Xda, but I sure wish I didn't have to send it in though.
How much did they charge you, about how long was the turn around, and did they at least install the new update for you?
Thanks everybody, got it fixed, someone on another post said it happen to him, just put back in the cradle and start the update all over again. I did just that and IT WORKED!!!!!!
Now I think I'm going to try to upgrade from 2003se to WM5, hope this goed more smothly, any suggestions out there?
Wouldnt that be the first thing you tried..?
Yea, if fact the instructions say to do exactly that but for some reason it didn't work the first time, don't know why.
Boot loder screen is all I see
I had the same problem with the latest (Nov 05) T-Mobile update. Tried to soft and hard reset, take battery out, change to new computer with active sync - nothing. After the Hard reset with record button depressed - nothing. Still Serial screen - replaced into cradel started the update and it worked. PHEW!!!!!
Thanks for the posts - really helped.
Tim
After a reset, my qtek 9090 displays "NO GSM" and "D 5.60.00 WWE". At device Information, shows:
Rom version: 5.60.00 WWE,
ROM date: 03/02/05.
RADIO version: (EMPTY)
PROTOCOL versionEMPTY)
and ExtROM versionEMPTY).
When i run an upgrade with "MaUpgradeUt_noID.exe" and nt.nbf, it works. But it dont accept radio_.nbf (ERROR 114).
Any idea? ty.
first try a soft reset (power botton + reset)
if u get still no radio
http://wiki.xda-developers.com/index.php?pagename=BA_Radio_1.15_Upgrade
follow this great tutorial and u'll get radio back
I followed the wiki tutorial.
Still no radio rom...
Could it be more than a software problem?
Try to press reset once, and then before the R: NONE G: NONE and D: (something) appears press reset again.
This should normally happen when removing battery and it is a common problem.
Is that what's happening to you ?
JP
i bought my wing off ebay and it came with the following specs:
ROM version: OpenTouch6L WWE
ROM date: 06/20/07
Radio version: 03.07.90
Protocol version: 4.1.13.51
i wanted to put it to the factory rom which is at 4.26.531.4 when i check at t-mobile's support site
during the rom flash, at 1% the phone resets on its own disconnects itself from the PC and shuts down activesync which then crashes the rom flash.
it resets normal and the phone still works under the opentouch rom.
is there anything else i can try?
what is the SPL of the device? It should be hardSPL'd, so you need to remove it first.
http://forum.xda-developers.com/archive/index.php/t-378735.html
welcome to xda-devs
i was able to reset it to the factory rom. i've read that when it appears to crash, during the splash screen do a soft reset and press the camera button for the flash to complete.
i bought my TyTN II yesterday, but it alwasy hang, i install nothing.. when hang at first time was after i used camera, then i remove the battery(i forgot that i can use soft reset) and then i try to personalize my device, then it hang again, so i soft reset, but after booting, it show notice that shell32.exe error, i try to hard reset but still hang sometimes, never go well, every times i'm using it, sometimes it stuck, i cant click it, so i have to soft reset it. i dont know what should i do... >_<
i bought it and already installed with
WM 6.1 pro
CE OS 5.2.19212 (build 19212.1.0.3)
ROM ver. : 3.29.707.0 WWE
ROM date : 05/07/08
Radio ver. : 1.65.16.25
Protocol ver : 25.83.40.02H
please help me, do i have to return the phone or i can repair itu by myself, but not void the warranty.. thanks..