Hi,
Anyone out there knows if we can remove hardspl from bootloader of Wing. Problem is my mobile displays splash screen, then switch offs by itself. Its been quite some time that I have hardspled it and have been using it. But recently I am facing this issue, so I am trying to move to original RUU and try if it works.
So for that anyone knows if we can remove hardspl from bootloader, because I am only able to enter bootloader. Moreover I tried several original roms from Flash Center as well as through SD card as well, but still be SPL version is 4.70.yang. Anyone knows any other alternative.
Also, if anyone has faced similar problem then kindly advice how you resolved.
Thanks in advance!
Regards,
Pankaj
Related
Hello. I was flashed my Wizard,but I have a general problem. When I try to start Windows, always start Align Screen, but Windows didn't start. I reflash my pocket, but the situation is a same. I think that I'm lost my BootLoader on PDA and the Wizard is unrepaired. I want somebody to help me, please?
bootloader
you can go into bootloader by soft reseting and holding the camera button down at the same time it will the show a multi colour screen that is bootloader mode
download your network providers official rom re flash it then is hsould bo ok
otherwise use a rom called wizard love i have seen use on many threads and it usually get people out of trouble search for it on goole
or if you have onshare i have the rom you can download my id is easymob same as the forum
http://www.onshare.com/en_gb/download/
What ROM did you flash with?
mordo said:
Hello. I was flashed my Wizard,but I have a general problem. When I try to start Windows, always start Align Screen, but Windows didn't start. I reflash my pocket, but the situation is a same. I think that I'm lost my BootLoader on PDA and the Wizard is unrepaired. I want somebody to help me, please?
Click to expand...
Click to collapse
You need to provide more details if you want help... what ROM version were you flashing? What provider? What was your IPL/SPL?
This is a beginner's mis conception. I was having the same problem. Eventually I found out that I need to keep holding the stylus on the screen for at least 6-8 seconds. Then the pointer will start moving. So it was not "tapping".
I was trying to flash my trinity but i am having problems,
I can get the phone into the bootloader mode without any problems
and the software see the phone ok but the update only gets 1% before it fails with "error 270 image is corrupt" i have tried many different image but the same occurs with them all.
My phone now only goes to the splash screen
is there any think i can do?
take a look at this thread, it may help you unbrick your Trinity...
thanks but no , my phone is not stuck in the bootloader just will not flash
Go HERE they might have a solution there!
Please don't double post! It will not give you a solution twice as fast
Hi. I had the same issue and solved it. feel free to send a MP if you still need help
Thanks still can not get working.. sent a pm to tonio94 thanks mate
Error 270
Hi m8,
Your error 270 is because your phone is still locked and the ROM(s) you are trying to flash are not natively signed for use on your particular phone!
You can either...
1. Pay to get your phone unlocked
2. Set your phone with Hard-SPL (see the related sticky on this very Forum)
3. Extract the .nbh file from the ROM you are trying to flash and flash it using the SoftSPL (SSPL) - again see the sticky on this very Forum.
Not being funny, but you really must do a bit of background reading before you start messing with these new ROM's on your phone.
I hope this helps - PM me if you need more detail.
Moz.
Same problem
Hello,
I've followed the thread to unlock cid/sim my 3600, but I can't upgrade nothing. I can't upgrade hardspl to.
With all roms, the phone stay on tricolor screen after "Yes" to allow enterbootloader.exe, and the rom tell me that the device is not connected.
Active sync was ok, the phone battery to.
Help?
I've 1.23.406 rom actually, and spl 1.07 ds.
EDIT: I've the soluce. I use the SSPL-TRIN for each upgrade, before the hard spl, before passing in 1.41, et now before the ROM, and it runs!!
I had not understood the thread about sspl-trin to bypass, so I didn't use properly.
Now it's ok...
Hi all,
Wondering if anyone had experience such problem before, and would know any solution to this problem, as per the title?
About two weeks ago, my Diamond could not load into the wm, and remains stuck on the screen.
I thought about doing a Rom Ugrade Utility, but since it cannot load into the windows for active sync, I wonder what else may I do?
If anyone has the answer to this, greatly appreciate if you may post your solution up.
Thank you!!
Hi,
If you haven't done it already, do a hard reset, maybe that works!
If not, try this:
When you're in bootloader screen,
plug in your diamond.
THere should appear the word 'USB' on your bootloader instead of 'serial'.
Then flash new HardSPL (I recommend 1.40 olinex http://forum.xda-developers.com/showthread.php?t=400950) via your pc.
After that it should be done!
I had the same problem as you, this worked for me!
Help help help...i just finished intalling duttys new leo 7 rom,now after restart my phone freezes on the 'smart mobility screen' i cant do anything more...i tried reset nothing.How do i get it to work please?
Have you followed the proper flashing procedure as explained here ?
Follow that guide and flash your phone again, it should be OK.
sounds like a bad flash, don't be scared it's quite simple.
if you are using the SD Card method, copy the file blacimg.nbh again to your card and flash again. or use anyother method.
i suggest that the safest way is the SD Card but make sure you have enough battery charge before you start
Has this been resolved?
Looks like it. He's posting in the radio rom thread today. http://forum.xda-developers.com/showpost.php?p=4862959&postcount=749
Lock plz.
it is specific to R7
I had the same problem with this R7.
To solve this i put the device in BootLoader mode and flash again.
But few times after the phone froze again and stuck. No way to make it boot cause it didn't go further than SmartMobility screen.
So i flashed a new rom to move from this scaring malfunction.
that is annoying cause this rom is very very pleasant and well optimized
Thread closed as query resolved
Hi I have an AT&T Tilt2. Ive been trying to flash it for about a month now. I was able to flash my pure without a single issue. I have loaded SSPL ran it on my phone then started manual flash. It Jumps from 0% to 100% then shows Error [266] Flash Write and says IU434 in the bottom corner of HardSPl. I have searched and searched and cannot figure out what im doing wrong. Any help would be greatly appreciated. If this has already been brought up and solved please point me to it. Thanks in Advance.
Why not just let the pros unlock your Tilt2?
Im not wanting to unlock it i just want to flash a different rom to it.
Problem solved i finally got it.