rained on my galaxy note. - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Yesterday my galaxy note got rained on now it says its charging all the time.mtp connected also shows up on notification. if turn the phone off I can't turn out back on again just shows battery charging. The only way to turn back on is hold home power and up boot into cwm then select reboot.If I plug USB in PC it doesn't register so no mounting sdcard.The phone works perfectly but says its charging with nothing plugged in.Is there away to unroot without connecting to PC.

As you say it yesterday I believe you have some light short circuit in the hardware or simply in the usb pins. There light acid in the rain (depending on where you leave) and that makes it a conductor.
Back in the old days what we did was take the phone apart and hair dry. But those where the big-a$s Nokias from late 90-s. This system is more fragile.
Actually you are doing the worst thing that you can do to it right now. That is turning it on and keeping it on. All you should do in my opinion is turn it off, remove battery and leave it in a dry place to dry up (~2 day). And only start using it after that. Every thing should be fine.
P.S: The Galaxy Note is not IP rated, so dont leave it out in the rain and dont take it with you to the shower

The phone only had acouple of spots of rain on it but was enough to cause problems.
However its has now recovered and working fine but be aware that the slightest bit of rain may brake it.

if ever you get an electronic device wet... put it in a container with rice... for at least 48hrs...
it has always worked for me... especially when I buy devices off CList that are water damaged, put them in rice for a week (swap out rice 3x), after i have SIMPLEGREEN'd them, then sell the mobo's for PROFIT on eBay...

thats a more Desi style

Related

[Q] Broken Cappy (Water Damage?)

Hello XDA, I'm hoping you guys can save my Cappy.
I had a rather big Saturday night of which I have no memory, and upon regaining consciousness Sunday morning my phone wouldn't turn on. I though no worries, its probably just flat, so I plugged it in and went back to sleep, when I tried to turn it on after waking, I got the Download screen, but it was red. I immediately took out the power and pulled the battery, and fearing water damage, placed it in a bag of rice, where it has remained since then.
TL;DR
1. I think my Cappy got wet, its in rice, is there anything else I can do.
2. If its not water damage, any other ideas?
Thanks in advance.
Not really.. if you've damaged your hardware, then you've damaged your hardware.. not much anyone can do about that.
You can try leaving it with one of those moisture absorbing silicon packets you occasionally find in new shoes or electronics, if you have any laying around.
I dropped my Cappy in a sink full of water and saved it by leaving it in a container full of rice for about 24 hours. Worked great. However, if the phone was exposed to water and it wasn't completely dry when you plugged it in to charge, you may be S.O.L. The last thing you want to do is run an electric current through wet circuitry. At this point you've done all you can. You just have to wait and see what happens.

[Q] Drunk G1 turns itself off

Hi fellas, long time no see!
So, first of all, yes, I've used the search, but what I've found is threads about wet phones, mine I believe is already dry.
Situation: I'm in the club, glass of absolut and redbull in my hand, phone in my jeans pocket, extra glass of absolut w/redbull on the bar next to me. Fat drunk aproaches the bar and tips my glass with his elbow, all my drink spilled over my clothes. After a brief discussion I realized the guy was too drunk and was a worthless douche so I let it go. I reach for my phone and realize my pocket is soaked wet, when I take it out, phone is out, red light dim. So I turn it off, take it apart and forget about it til the next day. Next day, it began to turn on, but shut itslef off after a few secs, so I take it apart again (that is back cover, battery, SIM and sd, I dont have the screwdrivers to go further), cleaned what I could with alcohol, let it vent in front of a fan for a few hours, then in a bowl of rice for 2 days, no good.
So I got an extra phone and let it sit for more than a month. The other day I decided to give it another try and voila! it worked, had to be dry by now! used it for a day, left it charging, when I came back, it was off again, unresponsive. I have an extra battery, so I got one of those universal battery chargers, because I though the problem could be the phone not charging the battery. It was (even when the light turns on red and it says charging and all). So, first weird thing, light turns on red, screen says charging, but USB wont wont actually charge the battery if it is somewhere below.. 70% maybe, it does charge if it is lets say about 80% or above.
I used it like this for a week or so, and now, when I turn it on, after the bootscreen and the initial loop, the phone now powers itself off (with the text "turning off" -or whatever it says- and vibrating and all), even with the battery full. Tried with both batteries full, plugged in the usb (the light is green when full, and will even charge), erased battery stats (recovery works fine) but the damn thing wont load android properly!
Any ideas what might be causing this? it should be dry by now (its been like 2 months already and I let it vent and used the rice method), it doesnt smell funny (you know, like burnt, like when sth short circuits).
btw, also tried flashing the ROM again (i always have a couple in the sd just in case) and didn't work neither, does exactly the same.
i know it is a bit long to read but i wanted to give you the most insight i could. i know that it works! it did a couple days ago, but something got screwed with the startup and i dont know what it is!
i see that u tried flashing the ROM again, but just to be sure u did do a super wipe correct?
this is very strange though, and yeah it should be dried by now.
Thanks for the reply, and yes, I did! I'm sure that is not the problem :/

[Q] Hardbricked handset whilst charging overnight

I've recently been experiencing some charging issues with the handset taking forever to charge, the latest charge was taking well over 15 minutes increase 1%. I tried various chargers, including a brand new original one (the one in the box).
Well, last night I put the phone on charge with the handset turned off around 2am, woke up around midday today and the handset was showing the green LED, so it was almost, or fully, charged. Went downstairs to have a cup of coffee and came back ten minutes later to find the LED off. Tried turning the phone on and nothing happened. Tried the reset combination and the red button under the SIM flap, nothing, tried connecting to SEUS, nothing. Tried connecting to Flashtool, nothing. I left the phone on charge for another hour and tried the same things again, nothing.
No lights, no vibrations, no screen activity. The phone isn't even getting warm like it normally does on charge (confirmed that with another charger)
My girlfriend said that whilst I was downstairs she did take it off charge and put it back on charge straight away when it wouldn't wake up BUT she wasn't sure if she put the charger back on the right way (the magnetic one) however the pins don't actually touch if the plug is the wrong way round as the pin towards the bottom of the phone is offset slightly so I don't believe it has shorted.
So great, my almost new Z1 is now a paperweight. Sony won't touch the handset as the back glass has a small crack in so they just spout off about water damage. The phone has never been near water, let alone in it.
C6903 on 757 firmware, bootloader relocked and non rooted. No nasty apps installed and basically running stock,
Anyone have any ideas? I'm resurrecting my old BB for the time being.
I bet its been shorted
Leave it on mains charger for 24 hours
gregbradley said:
I bet its been shorted
Leave it on mains charger for 24 hours
Click to expand...
Click to collapse
That's what I'm thinking. The design of the dosk pins should prevent that, but apparently it doesn't!
As probably there is stripes to check if water was inside I will exclude that. Also the magnetic connector have his way to plug so is close to impossible to revert it, hardly if you try maybe it will, but I did many time and nothing happened. At last I think you girlfriend mess up with you phone and now she now don't remember because she knows you will be furious...LOL...
BTW, I will press Sony to take look at it. They don't have to replace the cracked glass, they have to check where is the problem.
eclyptos said:
As probably there is stripes to check if water was inside I will exclude that. Also the magnetic connector have his way to plug so is close to impossible to revert it, hardly if you try maybe it will, but I did many time and nothing happened. At last I think you girlfriend mess up with you phone and now she now don't remember because she knows you will be furious...LOL...
BTW, I will press Sony to take look at it. They don't have to replace the cracked glass, they have to check where is the problem.
Click to expand...
Click to collapse
As you say, none of the water indicators (if I'm actually looking in the right place) are a different colour to normal. The dock pin is offset to one side slightly, it can be seen if you look closely so you are right, it really shouldn't have damaged the handset.
She isn't even sure if she did plug it back in! She was half asleep so I don't know lol
Sony will be getting some nasty words in a letter if they fail to do anything. I don't care about the glass, it doesn't bother me, as long as the phone works,

Moto G with Water Problem

Hi there. I had moto g 2 non lte this year. Sometime around spring of this year, i was on a vacation. While on vacation, I dropped my moto g and my bag into a river and thought i would never see it again.
A few days ago, the authorities said they had found my bag with all my possesions and my moto g. they shipped them to me.
I would like to know if there is any chance of recovering my device? So far, I've opened the back cover and saw it was covered in water. Some parts were also rusted. The display has weird purple blotches around the edge. I have tried to power on or charge the device. I have put the device in a bag of rice and put it in a warm area of my house.
Will I need to swap out any parts? Where could I find parts? I'm willing to replace parts. Also, where could I find instructions for replacing parts?
Thanks.
After sitting in water that long I'd be surprised it it ever came back from the dead. Also the worst thing you can do is to power on a wet phone. I would guess that you have some rust on the board, plus in the usb and earphone holes. I personally think the parts would exceed the value of the phone.
Hi there. I've opened up the main board, and I have not tried power it on. I've removed the battery, sim card, and buttons. The main bored appears corroded and I dried it off. If I dip it in 91% isoploryl alcohol, would it remove corrosion? I also saw corrosion in the ports. If I remove all the corrosion and water, logically the device would work again, right?
Anything is possible, you can also put a wet device in a bag of uncooked rice if no type of desiccant or silica powder is available. That will absorb moisture from places you can't see. As for alcohol, alcohol is a solvent and can dissolve the internal adhesives. If it was salt water, that's even worse since it dries and leaves crystals behind. I'll be shocked if you get it working completely after soaking in water. I'm surprised the sim card didn't get ruined.
Sent from my SM-T530NU using Tapatalk
At this point in time, I really don't care if the son card works or not. I just want to get to the point where I can power the device on and charge. I be read online in many places people suggested to dip your device in 91% isopropyl alcohol. Where can I get this alcohol and how much would it be? I have placed the device in a paper towel and put on top of a heating vent in my house. I'll see if that does anything.
That's regular alcohol that's sold at any drugstore or store that sells first aid stuff. You can buy it in different percentages of strength.
Sent from my SM-T530NU using Tapatalk
OH MY GOD. I CLEANED OUT THE INTERNALS, REMOVED ALL THE CORROSION I COULD WITH A TOOTHBRUSH, THEN SCREWED THE THING BACK TOGETHER. THEN I PLUGGED IT IN, AND GUESS WHAT, THERE ARE SIGNS OF LIFE!!!! The boot screen blinks for one second and goes away. There is a white led that constantly flashes. The device shows 0% charging. I have tried to boot it into recovery but the device keeps bootlooping. It turns on by itself, blinks white led, shows motorola screen, shuts off then repeats the process. I'll leave it to charge and see what happens.
Okay so maybe I reacted too quickly. I'm trying to get the device working. So far, I can boot it into fast boot mode and no further. My computer recognizes the device and can perform fast boot operations. I have tried to flash the stock firmware but the device reports error low battery remote failure on some operations. The device still does not boot. I plugged in the device for about an hour, but the second I take it off the charger, it cannot function. The device still is boot looping when it's plugged in. What should I do now?
Make absolutely sure there is no corrosion in the USB plug. After that, I don't have any ideas, something in the charge circuit has a problem or something between the battery and board.
Sent from my SM-T530NU using Tapatalk
I can't seem to remove the corrosion in the USB plug. Besides, I can plug my device into the wall or the computer and at least has limited function, however removing the plug will cause the device to loose power. The device shows up on my pc and I tried writing the factory image but the device is still in it's weird bootloop. My computer just keeps playing the USB disconnected and connected sound everytime the device does the bootloop. If I boot into fastvoor I can moto device manager to show and it says fastboot falcon s
That may be part of your problem. The corrosion in the plug could cause most of your problem. That port only costs 50 cents US, but I believe its tightly soldered in and if that's the case it would be very hard to replace without a special soldering gun.
Sent from my SM-T530NU using Tapatalk
Probabily your battery is dead

[Q] Can re-soaking fix water damage?

I know it seems like a stupid question but I've got nothing to loose at the moment so I'll explain my situation.
About 3 months ago I took my Xperia Z1 for a swim in the pool to see how the camera performed underwater. The screen started to go black when I took it out and then it completely shut off. I took it inside and turned it on again. It lasted a minute before shutting off so I plugged it in to the charger and got the boot logo before shutting off again with nothing: Screen was off, no led, no vibrations, nothing.
I opened the flaps and they were still white and still are today and there was no moisture or anything. I tried plugging the phone in a few days ago to see if it still works and the led turned on and it just stays like that with no action. Left it for a few hours but still nothing.
I don't really need this phone anymore because I have a Z5 now but a second handset is always nice to have. The pool water would have had a very small amount of salt in it and I think that might be causing issues. Either that or there is still water in there (unlikely) or parts have rusted or even the phone might have got shocked when I plugged it in to charge. What I was thinking was opening the ports and soaking it in water for a minute or less and then taking it out and putting it in a bag of dry rice to drain the water out of it. I'm not sure if it will work but I haven't got anything to loose so I was wondering if it is even worth giving a shot or even some tips would be nice.
tommylittle02 said:
I know it seems like a stupid question but I've got nothing to loose at the moment so I'll explain my situation.
About 3 months ago I took my Xperia Z1 for a swim in the pool to see how the camera performed underwater. The screen started to go black when I took it out and then it completely shut off. I took it inside and turned it on again. It lasted a minute before shutting off so I plugged it in to the charger and got the boot logo before shutting off again with nothing: Screen was off, no led, no vibrations, nothing.
I opened the flaps and they were still white and still are today and there was no moisture or anything. I tried plugging the phone in a few days ago to see if it still works and the led turned on and it just stays like that with no action. Left it for a few hours but still nothing.
I don't really need this phone anymore because I have a Z5 now but a second handset is always nice to have. The pool water would have had a very small amount of salt in it and I think that might be causing issues. Either that or there is still water in there (unlikely) or parts have rusted or even the phone might have got shocked when I plugged it in to charge. What I was thinking was opening the ports and soaking it in water for a minute or less and then taking it out and putting it in a bag of dry rice to drain the water out of it. I'm not sure if it will work but I haven't got anything to loose so I was wondering if it is even worth giving a shot or even some tips would be nice.
Click to expand...
Click to collapse
Resoaking your phone will help as much as trying to jump from a cruise ship in the middle of the ocean for the second time and you can't swim...
optimumpro said:
Resoaking your phone will help as much as trying to jump from a cruise ship in the middle of the ocean for the second time and you can't swim...
Click to expand...
Click to collapse
Haha yeah that's what I thought
tommylittle02 said:
Haha yeah that's what I thought
Click to expand...
Click to collapse
To clarify, the Xperia Z1 relies on closed ports to ensure waterproofing. So soaking it a second time would destroy it further.
there is a easy way you can try.
buy some electrical contact cleaner from a computer shop or maplins etc, spray that all over the circuitry and contacts and scrub it off with a paint brush, there is a good chance it will work again as it will remove any corrosion casued by water, ive repaired hundreds of water damaged phones this way and it doesnt need any special things.....

Categories

Resources