Related
Hello all
When I turn on my Tytn 2 it will come to a point were I have to enter my pincode - that's nice so noone can use my phone without the correct code. BUT if I at that point select "cancel" the Tytn 2 will just continue loading (not the phone function) but you will still be able to look in my calender and all the other stuff on my Tytn 2...
Is there a solution to this "problem" - I mean what I want is that it's not possible to start up my Tytn 2 unless you have the correct pincode...
Please help ;-)
Go to [Start]-> Settings -> Lock. Check the box [x]Prompt... and set your password. This is a windows password, separate from your SIM pin. This will prevent someone from using the PDA portion.
Note, they can always hard-reset (wipe) your device and use it afterward, but at least all the data will be gone.
Thank you
hey guys,
im new here and its also my first ppc.
ive got the following problem:
me (or my ppc) is not able to connect with activesync...
wtf can i do??
plz help me, thx,
LuFo
Install AS 4.5
Then connect your phone. Windows will first detect it as a new USB device and then AS will kick in and ask to set up a partnership.
Exactly what is going wrong with yours?
so, here we go:
ive got as 4.5 on my pc and ive recognized also that some other guys (even with older as) could connect to my ppc...
so, what is thie fckn prob??
again: plz help, what should i do?
greetz
PaulusUK said:
Install AS 4.5
Then connect your phone. Windows will first detect it as a new USB device and then AS will kick in and ask to set up a partnership.
Exactly what is going wrong with yours?
Click to expand...
Click to collapse
ok, i connest my ppc to the pc, its asking:
harddrive
or
as,
im typing as and its saying there isnt installed as 4.5
and the pc sais: no connection do u want to start the fixing??
(everythings translated by myself from german, plz ignore the faults)
grtz
i read that if you're using a usb hub it would not connect. you must have the usb cable connect straight to your pc's usb port.
and if nothing works the last solution is to hard reset your pocket pc for a frest start and see if it can connect then.
LuFo Diamond said:
ok, i connest my ppc to the pc, its asking:
harddrive
or
as,
im typing as and its saying there isnt installed as 4.5
and the pc sais: no connection do u want to start the fixing??
(everythings translated by myself from german, plz ignore the faults)
grtz
Click to expand...
Click to collapse
untick the advanced network functionality in the connection settings USB to PC and try again ...
swampy said:
i read that if you're using a usb hub it would not connect. you must have the usb cable connect straight to your pc's usb port.
and if nothing works the last solution is to hard reset your pocket pc for a frest start and see if it can connect then.
Click to expand...
Click to collapse
2nd that. Try another USB port on your PC. Sounds like there's either the driver missing (which should only be the case if you do not have Active Sync installed)
OR
try to disable the "Advanced network functionality". Can be found at 'Settings > Connections > USB to PC'. (Einstellungen, Verbindungen, USB zu PC oder so).
Do you have some sort of firewall software?
like, ZoneAlarm or antivirus with firewall?
disable them or allow the port as trusted and you should be fine
jeah,
thanks for this many posts, but ive got all these probs outa my way, these are all the things ive thought they may disturb the connection... but (im sorry) theyre no solution for my fckn prob, as told, my ppc connects to other pcs(with older as)but not to mine with the newest as ...
so, lets think how to manage it...
try rebooting the host PC or just kill mobsync.exe, wmdc.exe and WmdHost.exe in taskmanger. Then open Sync software again. Works for me.
thats an answer
thx a lot, ill try tomorrow...
all the wa<y, sometimes, when i stay the ppc connected and reboot my pc it works, but dont sync anything, its just "connected"...
ill try and post my answer soon.
LuFo Diamond said:
jeah,
thanks for this many posts, but ive got all these probs outa my way, these are all the things ive thought they may disturb the connection... but (im sorry) theyre no solution for my fckn prob, as told, my ppc connects to other pcs(with older as)but not to mine with the newest as ...
so, lets think how to manage it...
Click to expand...
Click to collapse
what OS do u have on your PC?
Did you download the newest WMDC also,
just checking http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center.mspx
here it is
LuFo Diamond said:
thats an answer
thx a lot, ill try tomorrow...
all the wa<y, sometimes, when i stay the ppc connected and reboot my pc it works, but dont sync anything, its just "connected"...
ill try and post my answer soon.
Click to expand...
Click to collapse
I think i have found a solution for you.
Follow:
Start Menu > Configuration > Connections > Click on the icon called "USB à ordinateur" (my phone is in french so i think it will be for you " USB" or "USB to PC")
It's written: Choose the connection type to PC
Select active Sync and uncheck the case just under (it is " activate the feature advanced networking")
And that is !!
TRY and say me..
Hi the diamond is my first PPC as well. I connected it in my PC and was able to use it as a HD. however i am having doubts of just unplugging it afterwards but i did just unplugged it after use.
On my second attempt. Diamond notified me if i will sync or use the HD i accidentally hit sync. but it required a password. I unplugged it and the problem beginned.
There is no Start Menu. so i did the soft reset on the red button below the stylus. It worked now, however the home screen does not have the Large Digital Clock now.
Can someone help me to display it back i have tried to check it in the Today menu. however it is still not appearing.
Pls.. help a new PPC user. Thank you.
cJosephaq said:
Hi the diamond is my first PPC as well. I connected it in my PC and was able to use it as a HD. however i am having doubts of just unplugging it afterwards but i did just unplugged it after use.
On my second attempt. Diamond notified me if i will sync or use the HD i accidentally hit sync. but it required a password. I unplugged it and the problem beginned.
There is no Start Menu. so i did the soft reset on the red button below the stylus. It worked now, however the home screen does not have the Large Digital Clock now.
Can someone help me to display it back i have tried to check it in the Today menu. however it is still not appearing.
Pls.. help a new PPC user. Thank you.
Click to expand...
Click to collapse
Try the search engine before you post, recently there where alot of topics on ActiveSync not working. Anyway, the way your PPC will act when you connect it to a USB port can be setup in setting, connections, usb to pc. Mark Diskdrive or ActiveSync.
There you should also unmark the advanced network functionality. Check it off and try again.
Rgds,
Thanks, by the way do you know how to display the Large Digital Clock again in Home. It was lost after i tried to soft reset my hanging Diamond.
Do you think it will appear again if i do a Hard Reset? Thanks.
cJosephaq said:
Thanks, by the way do you know how to display the Large Digital Clock again in Home. It was lost after i tried to soft reset my hanging Diamond.
Do you think it will appear again if i do a Hard Reset? Thanks.
Click to expand...
Click to collapse
A Hard Reset should bring it back to it's default value so yes I see no problem there ...
Blazeitup123 said:
try rebooting the host PC or just kill mobsync.exe, wmdc.exe and WmdHost.exe in taskmanger. Then open Sync software again. Works for me.
Click to expand...
Click to collapse
THX a lot, but all these programs are NOT running, ive tryed to run them and its juts possible tu run mobsync.exe mannually...
so this way would not work for me,
im sorry
on6hp said:
what OS do u have on your PC?
Did you download the newest WMDC also,
just checking http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center.mspx
Click to expand...
Click to collapse
my pc works with xp prof sp3
abinan said:
I think i have found a solution for you.
Follow:
Start Menu > Configuration > Connections > Click on the icon called "USB à ordinateur" (my phone is in french so i think it will be for you " USB" or "USB to PC")
It's written: Choose the connection type to PC
Select active Sync and uncheck the case just under (it is " activate the feature advanced networking")
And that is !!
TRY and say me..
Click to expand...
Click to collapse
jeah, this possibility is also told as the first option but , im sad, not the solution...
greetz
Last night i was playing with my gps ( Navigon - Google Maps - Google Nav) I switch the phone off at the comm Manager and left it off like that the whole night.
This morning when i switched it on, the phone refused to receive any signal.
Ive tried the following
Soft Reset
Hard Reset
Different Sims
Switching flight mode on and off aswell as the phone tabs
Ive changed the band from auto to gsm and back and still nothing
Gps, Wifi and everything else still works perfectly.
Before i return it and wait like 50 days for them to fix it, what can i try?
stevh0 said:
Last night i was playing with my gps ( Navigon - Google Maps - Google Nav) I switch the phone off at the comm Manager and left it off like that the whole night.
This morning when i switched it on, the phone refused to receive any signal.
Ive tried the following
Soft Reset
Hard Reset
Different Sims
Switching flight mode on and off aswell as the phone tabs
Ive changed the band from auto to gsm and back and still nothing
Gps, Wifi and everything else still works perfectly.
Before i return it and wait like 50 days for them to fix it, what can i try?
Click to expand...
Click to collapse
More information please. Rom, Radio, SPL?
Also have you tried calling your provider to ask if theres any problems at their end?
Mark.
I have no idea what rom..
lemme check..i have not changed a thing since i took delivery of the phone about 9 11 month ago.
my sim works perfectly in another phone.
rom 1.56.405.5
rom date 08.28.07
radio version 1.27.12.32
Does your sim work perfectly in another phone *in the same location* though? It was suggested you contact your network provider to see if they have any known issues or there are any reasons why your phone shouldn't be working. It may help if you have the IMEI number ready if you are in the UK, in case there is some reason why it has been blacklisted. If your TyTN II wont work with another sim in it (ideally from another network provider) and your usual network provider is unaware of any reason why this should be happening, then as a stock standard TyTN II, I think you'll have a good chance of having it looked at for free under warranty by HTC. Here in the UK I had my ROM reflashed from their WM 6.1 abomination back to the original WM 6.0 version by HTCs repair centre within one day so unless you choose a turtleback express postage option to send it in, there's no way it should take 50 days.
It started working all on its own again? how weird is that?
it had been normal ?
my tytnII had became the same after flight mode had turned on.
when fight mode off, it displayed "no service".
yiwangwuqian020 said:
my tytnII had became the same after flight mode had turned on.
when fight mode off, it displayed "no service".
Click to expand...
Click to collapse
you just use GSM-schen-HTC.Kaiser.CommManager.3G
hi, first thanks a lot,
my tytnII had this commManager software. I just used this commManager to turn on or off this flight mode .
how about no sim detected?
This problem is on my phone ,but this prog is not running perfectly. Error report at cca 95% full "sufficient system permissions"
Sorry for little English!
Please help me
radio:1.65.17.56
rom: through
Gastrocsaba said:
This problem is on my phone ,but this prog is not running perfectly. Error report at cca 95% full "sufficient system permissions"
Sorry for little English!
Please help me
radio:1.65.17.56
rom: through
Click to expand...
Click to collapse
after I reflash this tytn`s rom, it remain no service.
I think it had wrong with its gsm hardware.
Sorry for my english.
I found this problem too.( no service)
My solution is
1. I format rom by use MTTY tool.
(1. How to check and repair bad block
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Download Mtty.exe file in the attachment below and save it to your computer.
c). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
d). Put your divice into Bootloader mode and connect to your PC via USB
e). Run Mtty.exe from your PC
f). Selec "USB" in port box and then click OK
g). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks.
2. Flash Rom again.
3. Now Signal come.
And you turned your Kaiser into a BRICK...
... If your SPL supports "task 2a".
Since a few months I have been experiencing some serious issues with my TyTN II.
After being on for a while, it displays either:
No Service - While the reception in the area is just fine. Switching 'Phone' off and on in the Comm Manager fixes this problem, but then after maybe half an hour the same thing happens
Sim Card Missing - Apparently it can't read the SIM, a soft-reset usually helps in this situation.
I have tried several ROMs and Radios, and I even had the SIM-reader in the phone replaced. The SIM-card itself works fine in several other phones.
Does anyone have any experience with this? Any other suggestions as to what I could do? Any help would be greatly appreciated! Thanks.
tjado said:
Since a few months I have been experiencing some serious issues with my TyTN II.
After being on for a while, it displays either:
No Service - While the reception in the area is just fine. Switching 'Phone' off and on in the Comm Manager fixes this problem, but then after maybe half an hour the same thing happens
Sim Card Missing - Apparently it can't read the SIM, a soft-reset usually helps in this situation.
I have tried several ROMs and Radios, and I even had the SIM-reader in the phone replaced. The SIM-card itself works fine in several other phones.
Does anyone have any experience with this? Any other suggestions as to what I could do? Any help would be greatly appreciated! Thanks.
Click to expand...
Click to collapse
Have you tried other sim card on your phone and see what happens? Have you checked the sim card slot and see if there is nothing that's interfering the phone signal?
this is the same thing that is happening to me and there is no obstruction or anything interfering with the sim card connecting to the phone eventually i gave up on looking for a fix. So now i reverted to using my opal So the TyTn II just became my pocket pc now im going to flash wm6.5 jijijijijijjijiji but if somebody finds a fix please post it cause the tytn II was awesome but now its dead.
Same problem here
I'm having the same problem here. Already changing the sim flex and sim card reader, but still no improvement. Is there anything that I can do for this problem?
does anybody ever changing the upper board? is there any result?
same thing hapened to me..
tried sim in another phone and it works, tried another sim in the kaiser and no sim detected??
almost the same problem with my 8925
I have WM6.1 on it. It some time has a good reception, but in several minutes it says The SIM card is missing. Then it (not always, but sometimes) finds SIM itself. strange thing is, that if I flash WM6.5, it has almost no problems but it looses sound and camera doesn't work either...
Any ideas?
Thanks beforehand!
Tried Sim Card Flex replaced.
tjado said:
Since a few months I have been experiencing some serious issues with my TyTN II.
After being on for a while, it displays either:
No Service - While the reception in the area is just fine. Switching 'Phone' off and on in the Comm Manager fixes this problem, but then after maybe half an hour the same thing happens
Sim Card Missing - Apparently it can't read the SIM, a soft-reset usually helps in this situation.
I have tried several ROMs and Radios, and I even had the SIM-reader in the phone replaced. The SIM-card itself works fine in several other phones.
Does anyone have any experience with this? Any other suggestions as to what I could do? Any help would be greatly appreciated! Thanks.
Click to expand...
Click to collapse
> I did exactly just all that, using a Windows Mobile 6.5 Rom.
> After replacing the Sim Card Flex but Sim card still unreadable.
> Currently using back my Wizard, was thinking of changing the Flex Ribbon Cable but skeptical it will work unless someone have tried it.
> Found it on Ebay, check it out.
> http://cgi.ebay.com.sg/ws/eBayISAPI.dll?ViewItem&item=280555578532&ssPageName=STRK:MEWAX:IT
> Hope this helps abit
Almost the same with my Kaiser. The only difference, it doesn't show "No Service" message, shows network icon and name, but not available for calling. From time to time becomes available, after few seconds no more! After several hours of such unstable working, drops network at all, with no chanse of restoring it unless switching phone off/on. After that, performing as before.
I have installed a numerous versions of Roms and Radios, ranging from WM6.0 to WM6.5, tried Android, tried almost every combination of band, frequency, hsdpa and data setting with no help.
Is it possible hardware failure?
I did notice a micro switch in the sim card slot when I was tearing down my unit.. perhaps you want to play with the switch to see if other position may solve your issue.
same issue here...
tried everything...
Dear All,
Have you tried to connect an GSM external antenna to check if it improves the reception ?
Regards,
Nino
Sorry for my english.
I found this problem too.( no service)
My solution is
1. I format rom by use MTTY tool.
(1. How to check and repair bad block
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Download Mtty.exe file in the attachment below and save it to your computer.
c). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
d). Put your divice into Bootloader mode and connect to your PC via USB
e). Run Mtty.exe from your PC
f). Selec "USB" in port box and then click OK
g). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks.
2. Flash Rom again.
3. Now Signal come.
mtty fix
has anyone tried this? I'm having the same problem where my phone says no service and sim card missing, but i'm afraid to be the first to try this mtty fix as i've never used it before. Can someone confirm that it will fix this problem? Thanks to the guy that put it up ^
aekapolm said:
...My solution is....
Click to expand...
Click to collapse
master aekapolm...
i will try your solution!
aekapolm said:
...
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks...
Click to expand...
Click to collapse
after "info 8" my kaiser formatted... and i can not type "task 2a" ??????
i'm planning to change the flex cable cause mine has a cut in the middle and need to change the lcd due to crack
It's not the SIM card or the switch. That switch you're referring to will shut the phone off in the event that the SIM door is opened.
As for the "no service" issue, I understand that the HSPDA/3G radio part of the phone tends to go bad, especially with certain radio SPLs'. Once it's gone, it's gone for good. The only way to restore functionality is to replace the lower board which contains the radio, which includes the NAND (all your precious data).
I have seen some success with people using the 1.70 series of radio versions but it does not restore 3G/HSPDA, only 2G is functional, and the way networks are changing over to 4G, I don't see much of a future for 2G devices.
My advice... Find a replacement Kaiser with a cracked screen or other problem that doesn't involve the lower board and swap parts.
Out of curiosity, and asking for a mod to help on this:
This post is teaching newbies to KILL their phones, why was this thread revived?
Any newcomer please DON`T DO THE STEPS BELOW!! It will kill your phone.
aekapolm said:
Sorry for my english.
I found this problem too.( no service)
My solution is
1. I format rom by use MTTY tool.
(1. How to check and repair bad block
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Download Mtty.exe file in the attachment below and save it to your computer.
c). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
d). Put your divice into Bootloader mode and connect to your PC via USB
e). Run Mtty.exe from your PC
f). Selec "USB" in port box and then click OK
g). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks.
2. Flash Rom again.
3. Now Signal come.
Click to expand...
Click to collapse
Hi folks
this is the first time for me with WP 7 i am with the Android since the G1 lol.
i got an a focus s from a friend and i said to my self , why you don't try it? its locked to at&t, so the first thing i have to do is unlocking it.
at that point the problems started!!, i checked the unlocking cost via code, the average is 30$ which is expensive for 80$ phone!!, so i choose to unlock it via fastgsm and unlocking via USB cable.
i followed the instructions and everything seems to be OK till the last step when the phone reboots to the download mode, the program shows "FAILED" i had contacted teh customer support for fastgsm and they tried to help me, with o hope, thereafter i didscovered that there is somethign wrong with the connection of teh phone to the PC.
i start to read and read and read again "noting that i am expert in android things" and finally i decieded to use the CAb sender and/or the "sharp7eighter' to update then SIM unlock.
both programs with the same error "Device handshake failed" noting that the phone is connected and shows i937 in my compute but it never ever recognized by Zune, always says "no device connected"
sorry for my bad English, but i am very sure there is something i can do to :
1-go back to stock
2-update my phone
just to connected the fastgsm program to be able to SIM unlock it at acceptabl;e price 15$.
please and thanks
abudraih said:
Hi folks
this is the first time for me with WP 7 i am with the Android since the G1 lol.
i got an a focus s from a friend and i said to my self , why you don't try it? its locked to at&t, so the first thing i have to do is unlocking it.
at that point the problems started!!, i checked the unlocking cost via code, the average is 30$ which is expensive for 80$ phone!!, so i choose to unlock it via fastgsm and unlocking via USB cable.
i followed the instructions and everything seems to be OK till the last step when the phone reboots to the download mode, the program shows "FAILED" i had contacted teh customer support for fastgsm and they tried to help me, with o hope, thereafter i didscovered that there is somethign wrong with the connection of teh phone to the PC.
i start to read and read and read again "noting that i am expert in android things" and finally i decieded to use the CAb sender and/or the "sharp7eighter' to update then SIM unlock.
both programs with the same error "Device handshake failed" noting that the phone is connected and shows i937 in my compute but it never ever recognized by Zune, always says "no device connected"
sorry for my bad English, but i am very sure there is something i can do to :
1-go back to stock
2-update my phone
just to connected the fastgsm program to be able to SIM unlock it at acceptabl;e price 15$.
please and thanks
Click to expand...
Click to collapse
Fastgsm stopped working with the focus s when the newer firmware got updated, I think it was version LE2, I know I had to pay for more expensive unlock although in theory we can achieve unlock without paying anything with gsmtools etc, but this is risky as I don't really know how, it would require some experimental work!
As for connection issues
On keypad of your phone type ##634# and click "Call" button to show Diagnosis screen.
Type *#7284# onto Diagnosis screen, select "Modem, USB Diag." For fastgsm, and "zune" for...well, zune and confirm selection
Restart and let me know how zune sync now works
Sent from my arc 10HD using xda app-developers app
dazza9075 said:
Fastgsm stopped working with the focus s when the newer firmware got updated, I think it was version LE2, I know I had to pay for more expensive unlock although in theory we can achieve unlock without paying anything with gsmtools etc, but this is risky as I don't really know how, it would require some experimental work!
so, the safest way is pay the 30$, correct? noting that the firmware is in the attached pic
As for connection issues
On keypad of your phone type ##634# and click "Call" button to show Diagnosis screen.
Type *#7284# onto Diagnosis screen, select "Modem, USB Diag." For fastgsm, and "zune" for...well, zune and confirm selection.
i know, and i am already on the "Zune, USB Diag." option.
Restart and let me know how zune sync now works.
the zone still not recognize the phone (pic attached)
Sent from my arc 10HD using xda app-developers app
Click to expand...
Click to collapse
please see me comments above
here the Zune is not connected , noting the the PC is recognize the phone
abudraih said:
please see me comments above
Click to expand...
Click to collapse
Its zune, Not zune diag, select the top option and reboot, it should work then
Incidently its modem diag for fastgsm and not zune diag, as far as I could tell zune diag doesn't work with either!
still not working
abudraih said:
still not working
Click to expand...
Click to collapse
OK, there are a bunch of things we are going to try
Firstly are you in a position to hard reset your device from the boot loader?
If so do it, If not turn it off instead
turn your PC off
Plug USB cable in to a different port on the back of your PC, do not use a hub, it has been known that some hubs can affect sync
Turn both pc and phone on, assuming you have used a different USB port windows will install new drivers
Load zune and try again
Sent from my arc 10HD using xda app-developers app
i didn't use the phone yet, so i have no data to lose.
for the hardrest i did it many times, from setting , about, reset your phone then turn it off, press the three buttons together (power+camera+vol down) and format.
i don't know what you mean by headrest via bootloader.
and i changed the USB port and used 3 different types of USB cables, with no hope
and the strange thing is, when i plug the phone, the zune starts automatically and shows no device connected !!!
i am very sure that the previous user for the phone manipulate wit the software, so all i am trying to do is revert to stock, and i have another question regarding the download mode, when i was using the USB method from fastgsm to SIM unlock (screenshot attached), it shows that the PC detect the phone and read all information, but when it restarts to the download mode, it "FAIL".
the screenshot attached
abudraih said:
the screenshot attached
Click to expand...
Click to collapse
any thoughts ???
abudraih said:
any thoughts ???
Click to expand...
Click to collapse
I think its connected as a MTP device, that probably explains it..
OK,
Im going to hazard a guess with drivers being the problem
with the device connected I want you to do in to device manager and uninstall the driver for it, make sure you click delete driver as well.
then Disconnect the device before it can start installing it again
then go to http://www.nirsoft.net/utils/usb_devices_view.html and download the program at the bottom, make sure you choose correctly between x86/x64
this little program will allow you to view and delete all USB devices connected past and present. basically select the device, right click and uninstall it, you will need to run the program as admin
Have a field day and delete anything and everything that might be related to the phone, if you whack something that isn't related all you will have to do is reconnect it and it will install the drivers again so there isn't much to worry about.
try that and see if that removes what I think is a driver conflict. mind it might not be obvious what is and isn't related so best err on the side of caution and keep only those that definitely are not it!
Note it might be Samsung, or i937 or Windows phone or WP7 or more annoyingly USB composite device of which you will have many, just mind one of these will be a keyboard and mouse, if it stops just unplug and plug back in, windows will take care of the rest